OGAM - PO-340, ...Dip Chain Gang Rip Saw Specifications: -- 75 HP TEFC Motor, dip chain feed with overhead arbor. -- 4.3"; x 13.3"; Cut capacity. -- 16" Max. blade diameter. -- Power rise and fall. -- 70 mm dia. arbor. -- 2 HP Variable feed speed up to 115 FPM.Equipped with & Features: -- Automatic chain oiler. -- (3) Sets antikickback fingers. -- Adjustable infeed fence. -- Motor load meter. -- Many new saw blades.

OGAM MODEL PO-340 DIP CHAIN GANG RIPSAW ( THis is a Parts machine only )Specifications: -- 60 HP arbor motor, dip chain feed with overhead arbor, 13-3/8" (340 mm) max. rip cap. (between saw blades), 12-5/8" chain width. -- 9-13/16" Mn. to 13-7/8" max. blade dia., 4-3/4" max. depth of cut (manual raise and lower of the spindle), 70 mm dia. arbor runs @ 4,200 RPM; min. board length 19-3/4" (without short stock feed plate-see photo). -- Variable speed belted feed motor 20 to 100 FPM (approximate).Note From Seller: Ogam Gang Rip Saw. 60 HP motor 230/460. I don’t know much about this machine. Bought it used but haven’t been able to hook it up due to our current electrical service. The person I bought it from says it ran well when taken out of service. Can load on a truck.

OGAM - PO-340, ...Dip Chain Gang Rip Saw Specifications: -- 75 HP TEFC Motor, dip chain feed with overhead arbor. -- 4.3"; x 13.3"; Cut capacity. -- 16" Max. blade diameter. -- Power rise and fall. -- 70 mm dia. arbor. -- 2 HP Variable feed speed up to 115 FPM.Equipped with & Features: -- Automatic chain oiler. -- Magnetic Starters -- (3) Sets antikickback fingers. -- Adjustable infeed fence. -- Motor load meter. -- Many new saw blades. -- (3) Arbor sleeves & Spacers

OLIVER 4045 12" PROFESSIONAL TABLE SAW, with 36" FenceHeavy-duty cast iron table precision ground for accuracy; rugged machine frame construction provides maximum stability and reduced vibration.Specifications: -- 12" Blade capacity and 0° - 45° tilting arbor with digital read-out. -- 7.5 HP Motor at 3,450 RPM. -- Complete with: 52" rip fence capacity that will handle most of your work. -- 48" x 52" Cast iron table. -- Blade guard, miter gauge, push-button controls. -- Parts list & operation manual.

OLIVER 232 Table Saw w/BIESEMEYER FenceSpecifications: -- 12" Blade, 1" dia. tilting arbor 0° - 45°, 2 HP - 3,600 RPM belt driven arbor, 22" max. rip cap., 2-3/8" max. depth @ 90°, 1-7/8" max. depth @ 45°, max. dado width 13/16", 34-3/4" x 33-3/4" cast iron table, 34" table height. -- Complete with: -- BIESEMEYER Fence; 1-piece cast iron 25" square base; electric disconnect box & magnetic push button starter and small selection of saw blades.

OLIVER 4016 10" Table Saw, 5 HP, 3-Ph w/36" Rail Specifications: -- 5 HP motor; poly V-belt drive system with belts that run smoother and with less vibration, giving you the highest quality cut available. -- Top it all off with with OLIVER'S Optimus square tube fence and a digital blade angle readout system and you've got a saw that tears it up with accuracy and in style! -- Model 4016.004 5 HP, 220V. 3-Phase.

OMGA RADIAL 600 P3S Radial Arm Saw - 24" Crosscut Solid saw carriage with replaceable tempered steel sliding tracks. -- Carriage travels on (8) bearings with dust scrapers for smooth travel & extended track life. -- 180° Swivel of entire saw carriage for mitered crosscuts. -- 45° Saw head tilt for compound miter cuts. -- Spring loaded return for safe return of saw head after completion of the cut. -- Oversized replaceable wooden tabletop with full length back fence. -- Fabricated open steel base. -- Electromagnetic brake to stop the blade within (2) Seconds. -- Magnetic controls, push button controls & thermal overload switch. -- Options: Single-phase motor, Blade, Dado head guard, Dust collection system, and Roller tables for infeed & outfeed.

OMGA RADIAL ARM SAW 900-7 -- Specifications: -- 7 HP Saw motor, 35-1/2" crosscut cap. at 90°; 24-15/16" @ 45°; 5-7/8" max. thickness cap. at 90°, 4-3/16" at 45°; 43-5/16" rip cap.; 18" dia. blade with 1" bore; 2" max. dado cap.; 3,400 RPM arbor speed. -- Features: -- Solid saw carriage with replaceable tempered steel sliding tracks; carriages that travel on (8) bearings with dust scrapers for smooth travel & extended track life; 180° swivel of entire saw carriage for mitered crosscuts; 45° saw head tilt for compound miter cuts. -- Complete with: -- Spring loaded return for safe return of saw head after completion of the cut; oversized replaceable wooden tabletop with full length back fence; fabricated open steel base; electro-magnetic brake to stop the blade within (2) seconds. -- Includes: -- Magnetic controls, push button controls & thermal overload switch. -- Options: Blade, Dado head guard, Dust collection system, & roller tables for infeed & outfeed.

OMGA RN 450 Radial Arm SawSpecifications: -- 3 HP Saw motor; 12" blade; 17-3/4" crosscut cap.; 26-3/4" rip cap.; 3-1/2" @ 90° thickness cap., 2-1/2" at 45°; 1-1/2" dado cap.; solid saw carriage with replaceable tempered steel sliding tracks. Equipped with: -- Carriage that travels on (8) bearings with dust scrapers for smooth travel & extended track life.180° Swivel of entire saw carriage for making mitered crosscuts; 45° saw head tilt for compound miter cuts; spring-loaded return for safe return of saw head after completion of the cut. Complete with: -- Oversized replaceable wooden table top with full-length back fence; fabricated open steel base; electro-magnetic brake to stop the blade within (2) seconds. Includes: -- Magnetic controls, push button controls & thermal overload switch. -- Single-phase 2 HP motor available.

OMGA RADIAL ARM SAW MODEL 900 Series RN Solid saw carriage with replaceable tempered steel sliding tracks. -- Carriage travels on (8) bearings with dust scrapers for smooth travel & extended track life. -- 180° Swivel of entire saw carriage for making mitered crosscuts. -- 45° Saw head tilt for compound miter cuts. -- Spring loaded return for safe return of saw head after completion of the cut. -- Oversized replaceable wooden tabletop with full length back fence. -- Fabricated open steel base. -- Electromagnetic brake to stop the blade within (2) Sec. -- Magnetic controls, push button controls & thermal overload switch. -- Options: Single-phase motor, Blade, Dado head guard, Dust collection system, and Roller tables for infeed & outfeed.

OMGA Radial 1250-7 Radial Arm Saw -- Specifications: 7 HP Saw motor, 43.897" crosscut cap. at 90°; 6-7/8" thickness cap. at 90°, 4-7/8" at 45°; 59" rip cap.; 20" dia. blade with 1" bore; 1-3/4" max. dado cap.; 3,400 RPM Arbor Speed. -- Features: Solid saw carriage with replaceable tempered steel sliding tracks. -- Carriage travels on (8) bearings with dust scrapers for smooth travel & extended track life. -- 180° Swivel of entire saw carriage for mitered crosscuts. -- 45° Saw head tilt for compound miter cuts. -- Complete with: Spring loaded return for safe return of saw head after completion of the cut; 58" x 44" replaceable wooden tabletop with full length back fence; fabricated open steel base; electromagnetic brake to stop the blade within (2) Seconds. -- Includes: Magnetic controls, push button controls & thermal overload switch. -- OPTIONAL EQUIPMENT WHEN ORDERED WITH MACHINE: -- Automatic Air-Over-Oil Head Feed System, foot pedal activated, add $4,379.00 -- Vertical Pneumatic Clamp, add $ 675 -- Horizontal Pneumatic Clamp, add $929 -- RH or LH Roller Table, 6'-7" X 24", add $1,687 -- 3' Aluminum Fence Extension, add $410 -- 6' Aluminum Fence Extension, add $580

OMGA RN 450 Radial Arm SawSpecifications: 3 HP Saw motor; 12" blade; 17-3/4" crosscut cap.; 26-3/4" rip cap.; 3-1/2" @ 90° thickness cap., 2-1/2" at 45°; 1-1/2" dado cap.; solid saw carriage with replaceable tempered steel sliding tracks. -- Equipped with: -- Carriage that travels on (8) bearings with dust scrapers for smooth travel & extended track life.180° Swivel of entire saw carriage for making mitered crosscuts; 45° saw head tilt for compound miter cuts; spring-loaded return for safe return of saw head after completion of the cut. -- Complete with: -- Oversized replaceable wooden table top with full length back fence; fabricated open steel base; electro-magnetic brake to stop the blade within (2) seconds. -- Includes: -- Magnetic controls, push button controls & thermal overload switch.

OMGA 900/7 FM RADIAL ARM SAW Specifications: -- 7 HP Saw motor, 35-1/2" crosscut cap. at 90°; 24-15/16" @ 45°; 5-7/8" max. thickness cap. at 90°, 4-3/16" at 45°; 43-5/16" rip cap.; 18" dia. blade with 1" bore; 2" max. dado cap.; 3,400 RPM arbor speed.Features: -- Solid saw carriage with replaceable tempered steel sliding tracks; carriages that travel on (8) bearings with dust scrapers for smooth travel & extended track life; -- 180° Swivel of entire saw carriage for mitered crosscuts; 45° saw head tilt for compound miter cuts.Complete with: -- Spring loaded return for safe return of saw head after completion of the cut; -- Oversized replaceable wooden tabletop with full length back fence; fabricated open steel base; -- Electro-magnetic brake to stop the blade within (2) seconds.Includes: -- Magnetic controls, push button controls & thermal overload switch.

OMGA RN-700 RADIAL ARM SAW Specifications & features: -- 5 HP, 27-1/2" Crosscut cap. @ 90°; 19-7/16" @ 45°. -- Solid saw carriage with replaceable tempered steel sliding tracks. -- Carriage travels on (8) bearings with dust scrapers for smooth travel & extended track life. -- Self-centering locking in the positions of the main angles in (3) places, the saw arm (1), the motor & blade assembly swivel (2), and the motor carriage tilt (3); additionally manual locking at all intermediate angles. -- Easy and extremely practical unlocking of the arm for left/right swing on the front of the beam. -- Swiveling of the saw blade assembly and tilting of the blade on the vertical and horizontal axes. -- Standard overload protection with no-volt coil and motor brake. -- Spring-loaded return for safe return of saw head after completion of the cut. -- Oversized replaceable wooden tabletop with a full-length back fence. -- Fabricated open steel base. -- Magnetic controls, push-button controls & thermal overload switch. -- Options: Single-phase motors, Blade, Dado head guard, Dust collection system, & Roller tables for infeed & outfeed.

(2) OMGA RADIAL 900-7 FM Radial Arm SawsSpecifications: -- Max. crosscut cap: 27-1/2" wide x 5-3/4" deep (at 90°); 7 HP - 3,200 RPM motor, 16" saw blade cap. with a 30 mm x 70 mm saw arbor (see photo); the saw heads swivel & tilt both in the horizontal & vertical axis consistent with a standard compound miter saw. -- Saw heads can also be turned 90 degrees to the crosscut and cut parallel to the length of table utilizing as a rip saw. -- Table size is 35-1/2" x 144"; max. height adjustment from center of arbor to the top of table is 13-3/4; the max. adjustment between blades is 100-3/4". -- Equipped with: -- Auto feed selection for either single or double after simply locking or unlocking heads from the feed and utilizing the foot pedal for cycling; also has totally enclosed upper blade guards, missing gravity-type lower blade guards, 8-bearing saw carriages, automatic head return, self-braking motors with electromagnetic brakes (stops blade within 2 Sec. approx.), magnetic controls, and control panel. -- The added 7" mini-Safe light curtain, if broken returns the saws to their home position if they are lock in for auto feed.This saw comes with three used 1-1/2" wide dado sets, dado overhead guards, 2 pneumatic hold down clamps and 1 wide push clamp.

ONEIDA AIR SYSTEMS XXK050346 Cyclone 'High Vacuum' Cartridge Filter Dust Collector w/ One Drum: Cyclone & Cartridge Fabric Filtration Dust Collection System for High Pressure CNC applications (need more static pressure for effective cleaning of cutter heads). -- Performance: 2,120 CFM @ 2" SP with Filter. 5 HP US Made BALDOR , Class F, TEFC motor. Magnetic Starter w/ on-off switch and overload protection. -- Fan/Wheel housing: Extremely strong cast aluminum, non-sparking (per NFPA fire code). Efficient Backward Inclined high performance and low noise. No rivets or welds. Fully welded fan housing 11 ga. Motor Housing plate. -- Cyclone: (8") solid welded inlet with Neutral Vane. Technology reduces filter maintenance. 16-gage cyclone barrel with solid welded construction. Rectangular outlet cam be rotated independent of inlet - 8-bolt patterns. Outlet is 10.03" x 7.64" inside dimensions. Square to round adaptor available. Approx. 26" dia. cyclone housing. -- Efficient Filter Cartridge For 155 sq. ft. of filter media. Filters 99.9% efficient of 0.2 - 2.0 microns @ 11 FPM , wide pleated spacing and teflon-like interior coating for easy dust release. Filter size: (1) 18" x 39" & (1) 18: x 19.5". Filter Grounding Wire. -- Includes: Filter Efficiency Gauge. Built-in Silencer reduces sound to 75-81dBA @10' . One 55 Gallon Steel Drum. Top seal cover and flexible connection to cyclone discharge. Angle iron support stand w/leg extensions. -- Dimensions: 31" x 59" x 109.5".Available Options;Bag Gripper, Plastic Bag Hold-Down SystemHoppers / Multiple DrumsBin Level IndicatorRotary AirlockRemote Starter - Radio Frequency - 1 Phase onlyGE HEPA (H-12) Filter Media)Available with 600 Volt motor.

WEIMA TH 514 Briquette Press (Cylindrical). Produces 2" (50 mm) dia. x 4" (100 mm) long compacted logs. -- Specifications: -- Approx. 1.4 m³ vertical hopper, 12 HP (9 kW) motor; vertical hydraulic ram compacts the material in the extrusion chamber to produce uniform material, extrusion chamber is continually filled via rotary screw type auger. -- Approx. hourly output between 80 - 120 Lbs/Hr. ("quoted output is an average and can be influenced by density, material size, screen size, feeding form, and other factors"). -- Equipped with: -- Centralized control panel for easy operation, PLC Logic control & solid German engineering. -- Complete with: -- Auto on/off switch, auto length adjustment, & oil level sensor. -- Optional: -- Hydraulic oil heater, hydraulic oil cooler, transfer piping and customization to customer material handling.

WEIMA WLK 15 Vertical Hopper-fed Low Noise Grinder Specifications: -- Single shaft Shredder/Grinder, 59" x 59" rear-flared hopper opening; 3 cu. yds. cap.; 368 mm (14.5") rotor dia.; 150 HP motor; hydraulic ram with 4-sided serrated ram. -- Equipped with: -- Patented "V-ROTOR" design utilizes a V-groove rotor closely matched to grooves in the counter-knife to ensure uniform discharge free of splinters; reduce friction, and dedicate more horsepower to grinding. -- (82) Welded knives, (4) broaching cutters & (4) counter-knives, recessed concave cutters with low clearance over the rotor to extend cutter life, protect the bolts, and reduce machine wear. -- Features: -- Drop out discharge, hydraulically actuated lift up door for easy purge cleaning; extended screen basket; cut-out for conveyor (not included). -- Hydraulic serrated ram optimizes feed pressure by monitoring rotor motor amperage, lateral force on the ram is minimized by a unique "U-Joint" mounting system, Hydraulic clutch enables motor to start with the hopper full. -- Complete with: -- Heavy Duty structural steel frame, welded construction; integrated "plug-and-play" electrical control system with UL approved components. -- Recommended for plastic, paper or wood applications.

WEIMA C 150 Briquette PressSpecifications & Features: -- Produces 2" (50 mm) dia. Briquettes; -- Hopper opening of 41" x 41" (1,040 x 1,040 mm); hopper volume 1.43 cu/yd (1.1 cbm). Equipped with: -- 9 HP Hydraulic motor; 0.75 HP auger motor; hydraulic oil volume of 26.4 gallons (100 liters). -- Vertical hydraulic ram compacts the material in the extrusion chamber to produce uniform material; extrusion chamber is continually filled via rotary screw type auger. -- Volume reduction from chip/dust to block up to 10:1 ratio at 2,600 PSI; hourly output up to 80 - 120 Lbs/Hr ("quoted output is an average and can be influenced by density, material size, screen size, feeding form, and other factors").Features: -- Briquette length control, chrome plated clamp, oil level switch, control panel side-mounted to hopper, and overheating protection for hydraulic oil. Solid German engineering. - Freight, start-up, discharge pipes, etc. not included.

WEIMA TH 814 Briquetter A volume reduction of 90% is possible through the briquetting of wood, paper, aluminum and biomass or synthetics, providing significant savings in labor, disposal and storage costs.Material is hand fed or by dust system into the hopper, where an agitator pulls it into the auger and pressing chamber. Specifications: -- Produces 80 mm (approx. 3.1") dia. compacted logs; approx. 2.4 cu. yd. (55.1 x 55.1 x 37") square vertical hopper, 18 HP motor. -- Hydraulic ram compacts the material in the extrusion chamber to produce uniform material, extrusion chamber is continually filled via rotary screw type auger. -- Volume reduction from chip/dust to block up to 10:1 ratio; approx. hourly output between 300 - 400 Lbs/Hr.Features: -- Auto on/off integrated into feeding hopper; automatic briquette length adjustment; conical-shaped agitator; dust connection at pressing unit.Options: -- Hydraulic cooling for 24-hour operation, heating for cold weather start-ups; plastic tubing discharge into Gaylord or carousel bagging system. .