Photos coming! System includes: 24” in-line sander- Single head with buffing roller and clean up brush $340024” Double roll coaters 3ea-24” 2 bulb UV ovens 4ea24” Reverse rollcoaters 2ea24” 3 head brush denibber with double cleanup brushes 53” 2006 Heeseman sander- head 1 is a drum, head 2 is a cross belt, head 3 is a pad and has a clean up brush

There are (4) machines at this facility. Two are used in production and the other two are in storage. 87" Capacity

Fisher Ruckle 12' veneer Gilloutine. Very good condition.

Forestor 900 Resaw 4" Blades Powered Infeed

- End Matcher for the Continuous Feeding of Random Length Work Pieces - Minimum Working Length: 160mm (6.3") - Working Width: 30-250mm (1.18"-9.84") - Working Thickness: 10-30mm (0.39"-1.18") - Two 7-1/2 HP, 3ph Profiling Motors - Spindle Speeds: 6,800 RPM - Spindle Diameters: 40mm - Cutterhead Feed Motor: 1 HP - Two 1-1/2 HP Motors for Infeed/Outfeed Conveyors - Infeed/Outfeed Conveyor Sizes: 123" x 11" - Sound/Safety Enclosure - New in 2004 - Current Voltage: 460V

The Friulmac Randomat/SQ End Matcher has a Length Capacity 14" to 120" Width Capacity 2" to 10" Thickness Capacity .32" to 1" Feed speed 4 to 30 M/min Feed motor 15HP Scoring motors 4HP with 30mm diameter shaft, 7600 RPM Trim/Hogging motor 7.5HP with 40mm diameter shaft, 6000 RPM Profiling unit J-33 - 7.5HP with 40mm shaft, 6000 RPM Profiling unit J32 - 10HP with 40mm diameter shaft, 6000 RPM

Gabbiani Double End Tenoner Available approx August 1, 2023 Can also be paired with a direct transfer to a [Homag DET](https://www.carolinamachinerysales.com/listings/4073344-used-2006-homag-fl20-double-end-tenoner) at the same site.

Gannomat Pro-Line 50 • Row of holes as well as line drilling in the SYSTEM 32 mm • 50 (2 x 25) holes in one drilling cycle

25 Spindles 10 Dowel inserters 2 Dowel hoppers Glue tank Water tank Left and right adjustable fences 4 Pneumatic clamps foot pedal controlControl Panel

Laminating Rolls: 61" (155 cm) roll face with thermally conductive high release silicone surface; upper and lower main rolls internally heated; temperature controlled by state-of-the-art infrared sensors and digital PID controllers Laminating Opening: 1.5" (3.8 cm) maximum opening controlled with dual air cylinders. Laminating Material Uses heat activated and pressure-sensitive materials 0 - 55" (0 - 140 cm) wide on a 3" (7.6 cm) ID core Laminating Speeds 0 to 14.5 fmp (0 to 4.5 mpm) Post Lamination: Fanless cooling system provides uniform, filtered air for thermal shock without exposure to dangerous fan blades. Vinyl Transfer Complete roll to roll transfer, lamination, and edge trimming in one pass Safety Features • Two emitter-receiver photoelectric systems protect rolls from damage. • Emergency kick cables front and rear. • All electrical and moving mechanical parts are located in bolted cabinets • Four emergency stop buttons Installation Requirement 220 to 240 VAC, 50/60 Hz, 55A. 32 A per phase. Air: 2 cfm at 100 psi, minimum(0.5 m3 at 700 vPa)

Generac 200 HP Genset

Giben K305 Edgebander Manufacturer specs (to be confirmed): Standard Configuration Panel Thickness: 10~60mm Edge Thickness: 0.4~3mm Motor Power: 2.35Kw Maximum Curve Radius: 20mm Cutter Maximum Range: 50mm Working Pressure: 0.6 MPa Outline Dimension: 960 x 950 x 1000mm Gross Weight: 280Kg Voltage: 220-480V

Go Fast Single Head Resaw

Go Fast 5-Head Resaw Unit was cut into two pieces and can be put back together with a weld in the middle. Approx layout is 31' x 8'

Go Fast Resaw 15 HP Motor Put under power to test, never put into production.

3" - 41" length capacity 1" - 3" square or round diameter capacity 15 HP spindle motor Spindle speeds 2250, 3200, 3525, 4625 rpm hopper feed

Approximately 27" width capacity 1/2" - 3.9" diameter capacity 10 HP spindle motor 1800-3200 spindle speed 3 HP hydraulic feed PLC sequence controller

Gorbel 500 Lbs Ceiling Hoist

12' Arm 250 Lbs Capacity 4 HP Pump Per owner: head only turns horizonally

Griggio C250 Rip Saw 250 mm Wide belt (10")