BRANDT AMBITION 1680 EDGEBANDER (W/PRE-MILL & CORNER ROUNDING) -- Specifications: Edge thickness: 0.4 - 12 mm (0.02" - 1/2"); incl. 3 mm (0.12") PVC banding. -- Workpiece: Thickness 8 - 60 mm (0.314" - 2.375"). -- Min. workpiece width: 70 mm (2.76"); min. workpiece length: 160 mm (6.37"). -- Working height: 950 mm (37.8"). Equipped with: -- 3 HP (2.2 kW) Feed motor; variable feed speeds from 26 - 59 FPM (8 - 18 MPM); applying solid or using corner rounding units. -- Heated Infeed Fence. -- Infeed panel support with: Roller guide extends out to 800 mm (31.4"). -- Motorized top pressure beam adjustment with 0.16 HP (0.12 kW) Motor. -- 80 mm (3.15") Wide Heavy-Duty feed chain with: Rubber pads, automatic chain track lubrication. -- Top pressure section with: Double-wide compound V-belt to prevent panel movement. -- All cutting & trimming workstations are HF (High Frequency motors); line control (no limit switches) for workstation functions. -- Top & Bottom spraying device: Located in front of pre-milling station for easy residual glue cleaning. -- Manual adjustment in case of modified panel overhang. -- Automatic edge infeed. -- Reinforced guillotine for coiled edgebanding material; 0.3 - 3 mm (0.01 - 0.12") thickness & 8 - 45 mm (0.314" - 1.78") height. -- Centralized Lubrication system.Pre-milling Station: -- (2) 3 HP (2.2 kW) - 12,000 RPM Vertical milling/jointing heads; electro pneumatic jump control on 1st motor; electronic frequency inverter for control of motor speed & braking; SIKO digital units for vertical & horizontal adjustments.Glue Preheat Unit: -- 2.5 kW, 3 kG (6.61 Lbs.) cap.; glue viscosities: 25,000 - 80,000 mPa; temperature range: 120° - 245° C (248° - 473° F); max. melting capacity 6 kG/Hr.EVA Hot Melt Glue Application System: -- Quick change glue tank with Premelter for easy maintenance & glue color change; melting capacity: Approx. 6 - 10 kG/Hr; glue reactivating infrared heating unit positioned between glue roller & pressure zone to improved edge quality.Pressure Zone: -- Program controlled positioning of the pressure zone; (1) large driven & (3) secondary pneumatically controlled idle rollers.Workstations: -- Front & Rear End Trimming Unit with: Gap optimization, (2) 0.5 HP (0.35 kW) - 12,000 RPM motors, electro-pneumatic reset for straight or chamfer trimming. -- Top & Bottom Multi-stage Trimming Unit: (2) 0.73 HP (0.55 kW) - 12,000 RPM Motors with vertical & horizontal tracing; 2-position programmed controlled indexing. Position #1 with slight projection of 0.2 mm & Position #2 with flush trimming without projecting edge; Servo motor, controlled positioning of the work units and side copy for multiple edge thickness. -- Multifunction Profile Trimming Unit (Corner Rounding) with: Magnetic drive technology, (4) 0.54 HP (0.4 kW) - 12,000 RPM motors, 18 MPM (59 FPM) max. feed speed; 3 mm (0.12") max. edge thickness, 12 - 60 mm (0.50 - 2.375") workpiece thickness, quick-change motor system for different ra

BRANDT AMBITION 1440 FC (KDF-440 FC) EDGEBANDER (W/PRE-MILL & CORNER ROUNDING): -- Specifications: Edge & workpiece capacity: 0.4 - 8 mm (0.016" - 0.31") Edgebanding thickness, 8 - 60 mm (0.31" - 2.36") panel thickness, 160 mm (6.30") min. panel length, 70 mm (2.76") min. panel width.Equipped with: -- Heated Adjustable Infeed Fence: Radiant Heated with Manual adjustment. -- Joint Trimming/Pre-milling Station: (2) 2.2 kW (3 HP) 12,000 RPM Motors, left-hand & right-hand rotation with Pneumatic jump control for chip-free & clean panel edges. -- Roller Separating Device: 3 mm x 45 mm (0.12" x 1.77") or 1 mm x 55 mm (0.04" x 2.17") Max. roll cutting; 0.4 - 8 mm (0.016" - 0.31") strip thickness; 3 mm (0.12") PVC max. coil thickness. -- Hot Melt Glue Application Unit: 6 - 10 kG/Hr (13 - 22 Lbs/Hr) Melting capacity (depending on glue type). -- Pressure Zone: (1) Driven & (2) idle rollers; timed pneumatic pressure controlled; Servo motor positioning for programmable edge thickness changeover. -- Feed Speeds: 8 - 14 MPM (27 - 45 FPM); 11 MPM (36 FPM) when contour trimming. -- BRANDT "POWERTOUCH" Control with: 21" HD LCD Touch Screen Monitor.Workstations: -- Front & Rear End Trimming Unit: (2) 0.18 kW (1/4 HP) 12,000 RPM Motors with 0° - 15° automatic chamfer, pneumatic adjustment & activation/deactivation of edging material overhang using "POWERTOUCH" control. -- Top & Bottom Flush/Chamfer/Radius Trimming Unit: (2) 0.55 kW (3/4 HP) 12,000 RPM Motors, 0° - 25° Automatic tilt with Horizontal & Vertical Tracing wheels, Brushless multi-axis Servo motors for positioning of work unit & horizontal copy wheels for quick changeover with (3) Positioning options: Profile 1, Profile 2 & Flush Trimming. -- Multifunctional Trimming Unit: (2) 0.4 kW (1/2 HP) - 12,000 RPM Motors for Top & Bottom, Leading & Trailing edges & Corner Rounding of panels, Servo motors for positioning of work unit & horizontal copy wheels. Either radius or chamfer cutters can be mounted, 3 mm (0.12") max. edge thickness. -- Top & Bottom Multi-Profile (PVC) Scraping Unit: (2) Profiles: 1 mm (0.04") & 2 mm (0.08") or 3 mm (0.12") instead of 2 mm (0.08"); Servo control positioning of vertical & horizontal copy wheels; PVC scrape collection box, pneumatic adjustment using "POWERTOUCH" control, pneumatic disengagement. -- Top & Bottom Buffing Unit: (2) 0.09 kW (0.12 HP) - 2,750 RPM Motors.Complete with: -- Rubber padded feed chain w/top idle hold-down rollers; 1.5 kW (2 HP) feed motor; 32" diameter coil table; padded sound enclosure. -- Actual Model is BRANDT AMBITION 1440 FC (KDF 440 FC).

BRANDT KDF 110 (AMBITION 1110) Edgebander with Pre-Mill0.4 - 3 mm (1/8") Edge thickness cap., 8 - 40 mm (0.3" - 1.57") panel thickness, 60 mm (2.3") min. panel width and 140 mm (5-1/2") min. length.Equipped with: -- In-Feed Fence, adjustable, manual with digital indicator. -- Pre-Milling Unit, (2) motor, (1) jump, counter-rotating for the best possible glue joint. -- Gluing System, hot-melt, quick heat-up time and easy maintenance. -- Edge Magazine, automatic for strip & coil stock, 3 mm PVC guillotine, -- Side Pressure Section, (1) driven plus 2-idle roller w/digital readout setting.Workstations: -- End Trimming Unit, double motor end trim (2 x 0.5 HP - 12,000 RPM motors), chamfers 0° - 15°. -- Multi Trimming Unit, top/bottom for flush/bevel/radius trimming with (3) quick setting positions. Motors (2 x 0.5 HP - 12,000 RPM) with insert knives. -- Buffing Unit, top/bottom (2 x 0.5 HP) motors. -- NOTE: Open station at end; scraping unit could be addedControls:LCD Display, approx. 2 x 6" with soft-keys for fast navigation and operator comfort. Complete With: -- Feed Speed, fixed 8 m/Min (26 FPM), 3 HP feed drive. Sound enclosure and Scraper collection box.Actual Model: AMBITION 1110

BRANDT KD 56 EDGEBANDER0.4 - 3 mm (1/8") Edge thickness cap., automatic coil & strip feed magazine, guillotine for 3 mm PVC banding, fast startup (10 Min heat up) glue system. -- Workstations: Vertical travel double motor front & rear end trim, 0.25 HP - 12,000 RPM motors; top & bottom flush/bevel trimmers, bevel 0ø to 15ø, 0.35 HP - 12,000 RPM motors; top & bottom PVC scraping unit for up to 3 mm radius; top & bottom buffing unit, 0.15 HP - 2,750 RPM ea. motor; feed speed 30 FPM.

BRANDT KDF-520 EDGEBANDER (W/PRE-MILLING) -- Specifications:Edge thickness cap. 0.4 - 8 mm (5/16"). Panel thickness of 8 mm - 50 mm (5/16" - 2"). Min. panel length 160 mm (6-3/8") & 65 mm (2-1/2") min. width.Equipped with: -- Quick heat-up glue system (approx. 12 Min) w/quick change glue tank for maintenance & glue color change.Glue temperature indicator for both the glue pot & glue roller with LED thermostat, automatic temperature setback if the machine is idle for (15) Min or more.The glue applicator roller is reversible & retractable from the fence line. (1) drive plus (2) idle rollers "pneumatically controlled" pressure section. -- Automatic magazine for strip & coil (large 800 mm dia. coil table to accommodate large coils of 3 mm PVC) stock, 3 mm PVC guillotine. WorkStations: -- (2) Motor Pre-milling Unit with: (2) 3 HP motors (12,000 RPM) to clean-up potential chipped edges. -- End trim (0.25 HP - 12,000 RPM motors), chamfers 0° - 15°. -- Top & bottom flush/radius trim, bevels 0° - 15° (0.5 HP - 12,000 RPM motor), with insert knives for 3 mm PVC radius. -- Top & bottom scraping for 3 mm radius, pneumatically controlled indexing system. -- Top & bottom glue scraping. -- Top & bottom buffing (0.25 HP - 2,800 motors). -- Trim Stations have HF motors w/electronic brakes. -- Operator & Machine Control:"POWER CONTROL PC 20+" Control. -- Complete with: Feed chain track speed 11 MPM (36 FPM), 3 HP feed drive. &#9679 Operator control panel w/PLC (Programmable Logic Control) keypad & LED readouts. &#9679 Line control (NO limit switches) for workstation function. &#9679 Signal infeed light to insure proper spacing between panels. &#9679 Height adjustment with top pressure beam for all workstations. &#9679 Equipped with digital height indicator. &#9679 Safety hoods/doors. &#9679 Used tooling. -- Actual Model is BRANDT KDF 520

BRANDT KDF-550 C EDGEBANDER WITH PRE-MILL AND CORNER ROUNDING Edge & Workpiece Capacity 0.4 -8 mm (0.016 - 0.31") edge; 8 -60 mm (0.31" - 2-3/8") panel thickness; 160 mm (6.29") min. panel length and70 mm (2-.75") min. panel width.Equipped with: -- Pre-Milling Station with diamond cutter heads, (2) motors @ 2.25 kW (3.0 HP), 12.000 RPM, LH & RH rotation w/pneumatic jump control for chip-free and clean panel edges. -- In-feed Fence, with servo motor positioning. -- Automatic Edge Magazine, for strip & coil stock, strips 0.4 mm-8 mm (0.016- 0.31"), coils up to3 mm PVC and "HD" guillotine. -- Pressure Section,1st. roller driven plus (3) idle rollers, timed pneumatic pressure controlled; Servo motor positioning for programmable edge thickness changeover. -- Feed Speed, variable 8 - 14 MPM. (26 -46 FPM),11 MPM (36 FPM) when using contour trimming. -- BRANDT" PowerControl PC 16, Memory:256 MB Ram, 1 GB Flash Card Drive, Operator control panel w/22" color HD wide screen, soft keypad & internal modem for remote diagnostic link.Workstations: -- End Trimming, (2) Motor @ 0.35 kW (1/2 HP) 12,000 RPM, automatic chamfer from the control panel 0°- 15°. -- Flush/Bevel-Fine/Radius Trimming Unit: Top/bottom (2) motors, 0.55 kW (3/4 HP) 12,000 RPM, auto tilt positioning 0° - 25°, with combination flush/radius/chamfer cutterheads; horizontal and vertical tracing wheels. -- Includes (3) positioning options, profile 1, profile 2, and flush trimming. -- Corner Rounding Unit (1) Motor 0.35 kW (1/2 HP) 12,000 RPM for leading & trailing edges vertical corner rounding of panels; either radius or chamfer cutters can be mounted; 3 mm max. edge thickness. -- Scraping, Multi-Profile(PVC) Top/bottom with (2) profiles. 1 mm and 2 mm or 3 mm instead of 2 mm, servo control positioning of vertical & horizontal copy wheels.PVC scrape collection box. -- Scraping Glue Unit: Flush top/bottom on the panel surface with floating insert knives. -- Buffing Unit: Top/bottom (2) motors, 0.10 kW (0.125 HP) 2,800 RPM.Complete with: Motorized, programmable hold-down pressure beam; padded sound enclosure -- Actual Model is BRANDT, OPTIMATKDF 550 C

BRANDT KDN 210B Edgebander:0.4 - 3 mm (1/8") Edge thickness cap., 8 - 50 mm (0.3" - 2") panel thickness, 60 mm (2.3") min. panel width and 140 mm (5-1/2") min. length.Equipped with: -- Hot Melt granulate glue system with "Quick Melt" start-up (10 - 12 Min heat-up) with reversible rotation glue applicator roller and automatic reduction glue temperature adjustment (when idle drops to 150°, 2-1/2 Min to re-activate). -- Automatic feed magazine, coil stock feeds automatically with guillotine cutoff, all strip stock are fed automatically through strip feed magazine. -- 3-Roller pressure section (1st driven, next (2) idle) w/electronically controlled and feed speed synchronized drive roll.Workstations: -- Vertical travel double-motor front & rear end trim with tilting of 0°- 15° cap. (0.24 HP - 12,000 RPM motors). -- Top & bottom flush/bevel trimmers (0.36 HP - 12,000 RPM motors), bevel 0° to 15°. -- Top & bottom buffing unit (0.15 HP - 2,750 RPM motors). -- Feed speed of 30 FPM. Features: -- Operator control panel at eye-level. -- Automatic height adjustment with top pressure beam for all work stations. -- Digital height indicator on holddown beam. -- Electronic motor brakes on trimmers.Complete with: 200 Hz Electronic frequency inverter, used tooling, sound enclosure w/window, and operators manual.

BRANDT KDN 520 EDGEBANDER0.4 - 8 mm (5/16") Edge cap., panel thickness 15/32" - 2-5/32", min. panel length 160 mm (6-3/8") and 65 mm (2-1/2") min. width; line control (NO limit switches) for workstation function. Automatic height adjustment with top pressure beam for all work station, equipped with digital height indicator.Specifications: PC-16 Program Control; with 7-1/2" VGA screen 8 MB IDE flash disk, 8 MB RAM, Internal Modem for remote diagnostic link; Signal infeed light to insure proper spacing between panels.Equipped with: -- Quick heat-up glue system,(approx. 12 Min) w/glue tank for maintenance & glue color change. Glue temperature indicator for both the glue pot and glue roller with LED thermostat and automatic temperature reduction if the machine is idle for 15 Min or more. -- The glue applicator roller is also reversible and retractable from the fence line. -- Automatic magazine for strip & coil (Large coil table 800 mm dia. to accommodate large coils of 3 mm PVC) stock, 3 mm PVC guillotine, (1) drive plus (1) split secondary roller "pneumatically controlled" pressure sections.Workstations: -- Double end trim (0.33 HP - 12,000 RPM motor), chamfers 0° - 15° via programmable controller. -- Top & bottom flush/radius trim, bevels 0° - 15° (0.5 HP - 12,000 RPM motors), -- Top & bottom scraping for 3 mm radius, pneumatically controlled indexing system; -- Top & bottom buffing (0.25 HP - 2,800 motors).Features: -- End trim & flush trim stations have HF motors w/electronic brakes; feed chain track speed 36 FPM, 2 HP feed drive. -- Complete with: Operator control panel w/PLC (Programmable Logic Control) keypad & LED readouts, and used tooling. -- Machine still in use and available time to be confirmed.

BRANDT KDN 520 EDGEBANDER0.4 - 8 mm (5/16") Edge cap., panel thickness 15/32" - 2-5/32", min. panel length 160 mm (6-3/8") and 65 mm (2-1/2") min. width; line control (NO limit switches) for workstation function. Automatic height adjustment with top pressure beam for all work station, equipped with digital height indicator.Specifications: -- PC-16 Program Control; with 7-1/2" VGA screen 8 MB IDE flash disk, 8 MB RAM, Internal Modem for remote diagnostic link; Signal infeed light to insure proper spacing between panels.Equipped with: -- Quick heat-up glue system,(approx. 12 Min) w/glue tank for maintenance & glue color change. Glue temperature indicator for both the glue pot and glue roller with LED thermostat and automatic temperature reduction if the machine is idle for 15 Minutes or more. -- The glue applicator roller is also reversible and retractable from the fence line. -- Automatic magazine for strip & coil (Large coil table 800 mm dia. to accommodate large coils of 3 mm PVC) stock, 3 mm PVC guillotine, (1) drive plus (1) split secondary roller "pneumatically controlled" pressure sections.Workstations: -- Double end trim (0.33 HP - 12,000 RPM motor), chamfers 0° - 15° via programmable controller. -- Top & bottom flush/radius trim, bevels 0° - 15° (0.5 HP - 12,000 RPM motors), -- Top & bottom scraping for 3 mm radius, pneumatically controlled indexing system; -- Top & bottom buffing (0.25 HP - 2,800 motors).Features: -- End trim & flush trim stations have HF motors w/electronic brakes; feed chain track speed 36 FPM, 2 HP feed drive. --Complete with:Operator control panel w/PLC (Programmable Logic Control) keypad & LED readouts, and used tooling. -- Machine still in use and available time to be confirmed.

BREWCO Model BBBH 6-Head Horizontal Resaw;Complete with the following Features & Specifications: -- Working dimensions: 6" Wide x 8" high capacity and length 21" to 72". -- Band: 13'-2" x 1-1/4" x 0.035 Blade provides thin kerf savings. Quick & easy blade height adjustments. -- Wheel diameter: 28" Dia., CNC machined, dynamically balanced, all steel. -- Belting: Rough top feed belt combines with opposing side feed rolls. -- Saw motors: 20 HP High Efficiency, 3-Phase electric motor on each head. -- Variable feed speed conveying: 5 HP Hydraulic drive from 20 to 120 FPM (6 to 36 MPM).

BREWER Single-head horizontal Re-saw;With the following features: -- 15 HP motor. -- 6-1/2" wide x 6-1/2" thick resaw cap. -- 2-belt drive, 36" working height from the floor. -- Variable speed hydraulic drive with top and bottom powered tire and belt, 30" dynamically balanced band wheels at 900 RPM for vibration free running. -- 1" or 1-1/4" wide bands.NOTE: No return conveyor system.

20" Width cap., 1/4" - 9" opening, 7.5 HP motor (3-phase) with 1.5 HP feed motor, both made in the USA, variable feed speed 20 - 32 FPM.Complete with: Segmented infeed roller, cast iron chipbreaker and adjustable bed feed rollers; 3-knife cutter with jack screw adjustment. - Includes (2) sets of knives.

BRIDGEWOOD BW-511MS Sliding Table Shaper Single Phase 4 HP Motor with forward & reverse.Specifications: -- 3/4″ Spindle with 4-1/2″ under the nut, and 3-1/2" of Spindle travel. -- (5) Spindle speeds: 3000, 4000, 6000, 8000 and 10000 RPM. -- 52" Table Length, and 35 Sliding Table Length1-used BRIDGEWOOD BW-511MS SLIDING TABLE SHAPER. Table Length: 35″, Sliding Table Length: 52″, 3/4″ spindle with 4-1/2″ under the nut, Also , Spindle Travel: 3-1/2″, Motor: 4 HP, single phase, (5) spindle speeds: 3000, 4000, 6000, 8000 and 10000 RPM. For operation on 220V, 1PHNote- the feeder in the photo is not included

BRYAN - CL 240-W-GI, ...Hot Water Tube BoilerThis Boiler was taken out of an Office Furniture Factory where it was used to heat drying tunnels to a temp of 120 F.Disconnected and in storage for 1-1/2 years.Details & Specifications:Model: CL240-W-GIInput MBH: 2,160/1,080Output MBH: 1,728BRYAN #: 971292Relief Valve Setting: 50 PSIGHeating Surface: 287 sq/ftMAWP Water: 60 PSIGNational Bond #: 41033Canadian Reg #: E6190.25Gas Data:Natural GasMax Input CFH: 2,160Min. Input CFH: 1,080Min. supply Pressure: 7 In. WCMax supply pressure: 14 In. WCManifold pressure in WC: 3.5Orifice size: DMS 29

BURKLE - VBM 1688, ...Stain Wiping MachineSingle sided machine, 1,600 mm wide; 2-Brush Panel Cleaner (TAMPICO brushes). Features: &#9679 Heads can be positioned as needed spacing between the brushes by sliding brackets. &#9679 Brush raising & lowering accomplished by means of handwheel adjustment. &#9679 Brushes are removed at side of machine by sliding out of shroud/channel support rail. &#9679 Safety bar checks part thickness for overthickness parts. &#9679 SIEMENS Control to set rotation speeds & feed belt speed. &#9679 Rigid Aluminum bolted base construction. &#9679 Solid feed belt (NO vacuum holddown)

BUSELLATO B1CNC CNC MACHINING CENTER (UNIVERSAL): -- Specifications: Design Type: Cantilever Style, 49" x 120" universal phenolic machine table, multizone "Universal" vacuum table for use with pods. -- Equipped with:(1) 10 HP ISO 30 Type ATC spindle; variable speed from 3,000 - 18,000 RPM; (7) position side tool magazine; (1) Multispindle boring block (7-vertical, 4-horizontal) with an X-axis grooving Saw. -- PC-Based ControlWith "Windows 2000 Professional", GENESIS EVOLUTION programming software, Rail plan for pod location software, Autolink DXF conversion software, Autobar labeling software, Gencode barcode reading software. -- Complete with:(1) 80 Cubic meter rotary vane Vacuum Pump; assorted tooling; documentation; manuals and applicable software media.NOTE: This machine has very low usage and was used more like a Hobby/R+D CNC Machining Center by the owner.INCLUDES: -- CORAL - CA/3C Dust Collector; (3) canvas filter Bags; (3) HD plastic Collection Bags; 10" dia. intake flange; 3,105 CFM; 5.5 HP motor, 3/220/440 Volt; complete with on/off starter.

BUSELLATO JET 2 CNC MACHINING CENTER (W/ATC/BORING): -- Specifications: Working field: "X" Axis 120" (3,050 mm); "Y" axis 49.2" (1,250 mm); "Z" axis stroke 6.7" (170 mm); max. material thickness 4.7" (120 mm). -- Positioning Speeds:"X" Axis 197 FPM (60 MPM); "Y" axis 197 FPM (60 MPM); "Z" axis 66 FPM (20 MPM).Motion system utilizes Rack & Pinion and precision ball screws driven by AC Servo motors.The working head travels on high precision profile Guide Rail & Way Bearing System. -- Worktable:(6) Support rails with (4) panel lifters for heavy panels; (2) adjustable vacuum pods per rail. -- Boring Unit: 3 HP (2.2 kW) - 4,000 RPM motor; (12) independent vertical spindles: 7-Spindles in "X" axis, 5-spindles in "Y" axis.(6) Horizontal spindles: (2 + 2) Spindles in "X", (1 + 1) spindle in "Y". (1) "X" Axis grooving saw for max 120 mm dia. blade. -- Machining:(1) 10 HP (7.5 kW) Electro spindle with ISO 30 adaptor; variable spindle speed from 1,000 - 18,000 RPM. (1) 8-Position ATC tool plate for "on the fly ATC".(1) Additional 3 HP (2.2 kW) horizontal router mounted in "Y" axis. -- Operator & Machine Control:"PC" Front-End with: "TPA Genesis Evolution 2.2" + Windows 2000 Operating system; 32-bit INTEL Pentium III Processor - 1,000 MHz, 10 GB hard drive.15" Color monitor, international keyboard, soft touch keypad, & industrial mouse; (4) serial ports, (1) parallel port, (2) USB ports, (1) 1.44 MB floppy & (1) CD ROM disk drives. "Genesis Evolution" is a real-time multitask Processing System with data & error diagnostics; programs can be transferred via diskette or possible downloading by wire. -- Complete with:(1) 100 cbm/Hr BUSCH Vacuum Pump; scrap conveyor; safety mats; safety hood; all backup disk, documents, & manuals associated with this machine. -- Actual Model is: BUSELLATO JET 2.

BUSELLATO JET 4002 XL CNC MACHINING CENTER (W/ATC/BORING): -- Specifications Working Field "X" Axis of 168.1" (4,270 mm); "Y" axis of 47.2" (1,200 mm); "Z" axis stroke 9.8" (250 mm); 6.8" (175 mm) max. material thickness. -- Positioning Speed"X" Axis at 230 FPM (70 MPM); "Y" axis at 197 FPM (60 MPM); "Z" axis 49 FPM (15 MPM). -- Worktable(8) Pneumatic locking panel supports; (2) vacuum pods per support.(8) Pneumatic backstops; (2) pneumatic side stops & (2) pneumatic central stops.(4) Independent working zones; jig locking device on (2) work areas. -- Boring Head(1) 4 HP (3 kW) Motor - 4,000 RPM; (20) vertical spindles with (12) spindles in "X" axis & (8) spindles in "Y" axis. -- Machining(1) Vertically mounted 10 HP (7.5 kW) electro spindle with ISO-30 adaptor (0 - 18,000 RPM) with RH or LH rotation; (1) 6-position automatic tool changer.(1) Additional 5 HP (3.8 kW) vertical Routers; Routers are driven by an 11 kW digital Inverter. -- Operator & Machine ControlPC Front-End with: "GENESIS EVOLUTION" 2.2.1 + Windows "NT" Operating System; 15" color monitor; 1.44 MB floppy & 32X CD ROM drives; 8.4 GB hard disk; 64 MB RAM; (2) RS 232 serial ports; integrated modem; Ethernet card, all built into a protective cabinet enclosure.GENESIS Software is continuously online providing real-time information on tool position & error messages; visualization of RPM, current load meter, and more; positioning of panel supports and vacuum cups.Software Features: Automatic generation of G & M code, stop & restart, machine diagnostics, automatic optimization, and full graphic display with the possibility to associate up to (11) parameters and programming of up to (2,000) work lines per single program. -- Complete with:Front safety mats that will instantly place machine in "Pause Cycle" when operator steps onto the mats. -- Actual Model is BUSELLATO- Jet 4002 XL.

CAM-WOOD MODEL TRS-3000TB.12" SLAT RIPPER - (1) top & (1) bottom rip spindle.CAM-WOOD MODEL TRS-2050TB.8" SLAT RIPPER - (1) top & (1) bottom rip spindle - DEDUCT $8,000FEATURES: -- The machine can plane or shape the wood at two surfaces then rip it. Ideal for shutters, louver slats, yard stick blanks, etc.. -- Special profile hold down & groove table for slat ripping, optional -- Designed to meet the exacting standards required for high quality production line use. -- CAM-WOOD’s Slat Rip Saws are manufactured to precise tolerances, and feature the newest designs for operator safety and volume production. -- All of these features combine to show what a true value these machines are in today’s highly competitive market. -- Precision fence assures absolute accuracy between cutterheads & fence and is equipped with measuring gauge. -- Double anti-kickback fingers mounted at the infeed end of the machine provided maximum safety protection. -- Heavy duty industrial TEFC motor ensures full depth cutting capacity in all materials. -- Ruggedly constructed steel frame for durability and extended machine life. -- The variable speed feed works allows the machine to meet the cutting requirements of different materials. -- Saw heads built to precise tolerances assures accuracy for all ripping and profiling operations provide a stellar quality of cut. -- Top & bottom powered pneumatically tensioned pressure rollers for precise feeding and cutting. -- Saw arbor is manufactured from alloy steel for dependability and anti-fatigue, heat treated, precision ground and balanced providing precise cutting performance.SPECIFICATIONS: -- 12"; Max. Cutting Width (TRS2050 WITH 8" MAX. WIDTH) -- 4-3/4"; Max. Cutting Depth -- Min. Cutting Depth Limited by Thin Material Breakup -- 10"; Min. Workpiece Length -- 14"; Dia. Max. Sawblade Size on Top Spindle -- 10" to 16"; Dia. Sawblade Size on Bottom Spindle (TRS2050 WITH 16" DIAMETER) -- 4,000 RPM Top & Bottom Spindle Speed -- 12"; Spindle Length (TRS2050 WITH 8" SPINDLE LENGTH) -- 40mm Arbor Diameters with 2-Keyways (TRS 2050TB WITH 70MM ARBORS) -- 15 HP Top Rip Saw Motor (TRS 2050 WITH 10 HP MOTOR) -- 30 HP Bottom Rip Saw Motor -- (6) Upper and (2) lower Feed Rolls -- 12 to 60 FPM Feeding Speed (Variable) -- 1 HP Feed Roll & Top Head Elevating Motor -- 1/2 HP Lower Saw Arbor Elevating Motor -- 7-1/2 HP Feed Motor (TRS2050 WITH 3 HP MOTOR) -- Dimensions (L x W x H) 96" x 64" x 55"

CAM-WOOD MRS-340-1M Dip Chain Gang Ripsaw with one Shifting Blade:Specifications: -- Cutting width up to 13";; machine will pass thru 25-1/2"; -- 3"; Maximum depth of cut with 12"; diameter blades. - Will cut 4"; thick with 14"; blades (optional). -- With 70 mm saw spindle; accepts 90 mm bore sawblades -- With air-loaded pressure rolls, standard fence, and feed chain. -- Urethane Chain Pads and Pad Holders optional -- With (1) powered moveable blade and fixed blades. -- Moveable blade controlled with a joystick. -- With (10) push buttons for pre-programmed selective ripping -- The shifting blade moves at 20 to 80 mm/second (up to 3"; per second). -- Moveable saw blade traverses from 0.59" thru 13.38" -- 50 HP Saw arbor motor; -- 3 HP Feed motor with feed speeds from 15 to 130 FPM -- (2) 1/2 HP Lift motors for pressure rolls and saw arborOptional Equipment when ordered with the machine: -- TRS-FT AUTOMATIC INFEED CONVEYOR SYSTEM, with Movable Fence with Digital Display and Shifting Laser Light for Rip Width Setting: .. -- Hydraulic Quick Lock Spindle Assembly. The hydraulic locking spindle assembly is designed to provide for quick changeover between various ripping requirements. Simply turn the locking knob to pressurize the arbor and lock the blades in position. Turn it in the opposite direction to unlock the blades. The sawblades are mounted to solid steel blade collars: ... -- Additional Quick Set Mechanically-Locked Saw Collars for fast, accurate, sure holding of saw blades in any stationary position ... -- 60 HP Saw Arbor Motor: -- Additional 30 MW Laser Unit with Bracket & Wiring: ... -- Pneumatic Pressure to Hold Down Feed Rollers (In lieu of spring pressure). Provides better control of the product being fed. Each pressure roll is controlled by an individual pressure regulator: .. -- Short stock feeding device for 14"; blades (see specifications for cutting capacity information): -- Feed Chain with (69) Easily Replaceable Bolt in Cast Iron Pads. Allows for changing chain pads as they wear or get cut into rather than replacing the complete chain assembly. NOTE: Specially ground down to 0.06"; square tip for optimum hold with virtually no marking: ... -- Feed Chain with (69) Easily Replaceable Urethane Non-Marking Strip Inserts. Urethane is vulcanized to metal backing bars and bolted in place: ... -- 12" Dia. carbide tipped ripsaw blades, cuts up to 3" material: ... -- 14" Dia. carbide tipped ripsaw blades, cut's up to 4" material: ...NOTE: Foot Pedal seen in the photo is only used with a powered Infeed Table and is designed to release boards from the Feed Table.