• Used
  • New
 
  •  
 
  •  
 
  •  
 

 
21 Results Found for Multiple Drill Single Viewing 1 - 20 of 21 results
STANDARD LISTINGS
CEMCO MBV 54 Vertical Boring Machine -- 54" x 15" Cast iron table with 54" x 24" wooden top,Equipped With: -- (6) universal spindles with movable spindle supports, -- (6) 1 1/2 HP - 1,725 RPM direct drive spindle motors, -- 1-1/2" min. center-to-center distance; -- (1) spring loaded holddowns, -- 36" stationary table height; -- 6" max. vertical stroke, spindles advance hydraulically at 0 - 30 strokes/Min; -- Foot pedal actuated w/single cycle & continuous automatic modes; -- 2 HP hydraulic feed pump, 12-gal. hydraulic pump system;
Equipment Location:SOUTHEAST
Louis Sicotte
800-374-5009 ext:329
CEMCO MBV 54 Vertical Boring Machine -- 54" x 15" Cast iron table with 54" x 24" wooden top,Equipped With: -- (3) universal spindles with movable spindle supports, -- (3) 1 1/2 HP - 1,725 RPM direct drive spindle motors, -- 1-1/2" min. center-to-center distance; -- (1) spring loaded holddowns, -- 36" stationary table height; -- 6" max. vertical stroke, spindles advance hydraulically at 0 - 30 strokes/Min; -- Foot pedal actuated w/single cycle & continuous automatic modes; -- 2 HP hydraulic feed pump, 12-gal. hydraulic pump system; Also included: -- Custom built tubular back fence with left side fence stop -- Currently wired with (8) on/off switches & electrical disconnect
Equipment Location:SOUTHEAST
Louis Sicotte
800-374-5009 ext:329
CEMCO MVB 84 Vertical Boring Machine -- 84" x 20" table with 84" X 15" boring area, 71" between columnEquipped with: -- (6) 1. HP spindles, each spindle with on/off switch control, 1 1/2" min. center-to-center distance on vertical spindle; -- 2 HP hydraulic feed pump w/variable speed control and 18 gallons reservoir. -- Moving table with 8" stroke and up to 30 stroke per minute. -- Manual and automatic mode of operation , foot pedal cycle activationAlso included: -- Protective guard in wire meshNote: Picture of the machine are before it will be cleaned and checked
Equipment Location:SOUTHEAST
Louis Sicotte
800-374-5009 ext:329
CEMCO MVB 84 Vertical Boring Machine -- 84" x 20" table with 84" X 15" boring area, 71" between columnEquipped with: -- (5) 2. HP spindles, each spindle with on/off switch control, 1 1/2" min. center-to-center distance on vertical spindle; -- 2 HP hydraulic feed pump w/variable speed control and 18 gallons reservoir. -- Moving table with 8" stroke and up to 30 stroke per minute. -- Manual and automatic mode of operation , foot pedal cycle activationAlso included: -- Protective guard in wire mesh
Equipment Location:MIDWEST
Louis Sicotte
800-374-5009 ext:329
CEMCO MVB 84 Vertical Seat Boring Machine -- 96" x 20" table with 84" X 15" boring area, 71" between columnEquipped with: -- (16) 1.5 HP spindles, each spindle with on/off switch control, 1 1/2" min. center-to-center distance on vertical spindles; -- 4"max. spindle stroke; Spindles advance hydraulically at (0 - 30) strokes/Min, -- 2 HP hydraulic feed pump w/variable speed control and 18 gallons reservoir. -- 36" Stationary table height. -- Manual and automatic mode of operation , foot pedal cycle activationAlso included: -- Several boring Template for chair seat -- Protective guard in wire mesh
Equipment Location:SOUTHEAST
Louis Sicotte
800-374-5009 ext:329
(2) Spindles, 1 HP - 3,500 RPM motor, Max. material thickness 8-1/2", max. distance between spindle centers 3/4" to 3", max. -- Designed with: Max. spindle stroke of 3-7/8"; vertical table travel to center of bit 3-1/2", table size 15-3/4" x 9-7/8"; (1) pneumatic adjustable holddown cylinder. -- Complete with: Cast iron table with dovetailed miter gauge slots, miter gauge, adjustable stock stop, adjustable boring head, drill bit adapter, steel cabinet base, foot pedal control.
Equipment Location:MIDWEST, AL
EX-FACTORY INC.
704-841-2001
12" X 80" Material holding area, (2) horizontal + (2) end boring motors with a capacity of 60" between boring unit & 2 vertical from bottom unit with maximum drilling distance between the units of 80", all motors 2 HP - 3600 RPM; horizontal boring units have 4" vertical adjustment, 22° side to side and 15° up & down; end boring units have 14-1/2" front to back adjustment, 45° toward front, 22° toward back and 15° up and down; 6" max. drilling stoke, adjustable with stops, 0 - 180 in./Min. boring speed, infinitely adjustable, 7" min center to center of boring units; air activated with foot pedal control, 90 PSI air requirement; Includes: (2) Air clamps with 8" max. clamping capacity. -- Note the 3 spindles boring block are not included with the machine.
Equipment Location:SOUTHEAST
Louis Sicotte
800-374-5009 ext:329
NORTHTECH NT-SDH-10HD Horizontal Boring MachineMultiple Spindle Horizontal Boring machine equipped with:: ● (2) 5 HP motors belted to the boring spindles driven at 3,500 RPM. ● (12) drill spindles with keychuck 3/8" capacity, minimum distance between 2 spindle 45 mm (1.77"). ● (5) pneumatic hold-down clamps; pneumatic feed system for the movement of the drilling spindles to the work surface; ● Stroke capacity of 125 mm (5") actuated by foot pedal. ● Max. boring height of 90 mm (3-1/2"); ● Work table is 120" long x 13 1/2" wide. .
Equipment Location:NORTHWEST
Louis Sicotte
800-374-5009 ext:329
RITTER R803HD HORIZONTAL BORING MACHINE(2) Single spindle belt-driven heads, RH rotation; 2" center distance between the (2) spindles, 1 HP belt-drive motor on ea. head. -- Head adjusts via hand crank from 2" - 10" on inside spindle centers, 0" - 3" adjustable spindle stroke; 0" - 4" adjustable table height, 10" x 24" cast iron table size; 7/16" 14-screw shank, 3/4" max. bit cap. Complete with: -- Air operated overhead holddown clamp and foot pedal operated drill cycle.
Equipment Location:MIDWEST
Louis Sicotte
800-374-5009 ext:329
RITTER R803HD HORIZONTAL BORING MACHINE(2) Double spindle belt-driven heads, RH rotation; 1" center distance between the (2) spindles, 1 HP belt-drive motor on ea. head. -- Head adjusts via hand crank from 2" - 10" on inside spindle centers. -- 0" - 3" Adjustable spindle stroke. -- 0" - 4" Adjustable table height. -- 10" x 24" Cast iron table size. -- 7/16" 14-Screw shank, 1/2" max. bit cap. Complete with: --Air operated overhead holddown clamp -- Foot pedal operated drill cycle.
Equipment Location:MID ATLANTIC
Louis Sicotte
800-374-5009 ext:329
ROOT D-200 Horizontal Boring Machine;80" x 15" Table, (4) horizontal spindles, all spindles with 1 HP motors, single drill heads, left to right head adjustments. -- Maximum center distance between outside motors is 72", 9" maximum spindle stroke; hydraulic spindle stroke adjustable from 10 to 40 IPM. -- 6" Vertical adjustment of table, maximum thickness of stock under clamps - 8", holddown bar with (4) holddown pods; 5 HP hydraulic pump.
Equipment Location:MIDWEST
Louis Sicotte
800-374-5009 ext:329
RYE DB50 Horizontal Boring Machine -- Horizontal boring machine with (2) boring unitEquiped with: -- (2) 3 HP - 1,450 RPM motor, equipped with a 2-spindle boring head, gear driven @ 3,000 RPM and adjustable center -- Maximum distance between boring unit is 24" -- Compressed air feed with horizontal travel of 6" deep in hard- or softwoods. -- Tilting table (front/back) with raise and lowering mechanism for 4" vertical adjustment. Complete with: -- Pneumatic holddown cylinder, -- Push button magnetic controls.
Equipment Location:WEST COAST, AL
EX-FACTORY INC.
704-841-2001
SICOTTE J 20-4 Horizontal Boring Machine: -- 12" x 48" Steel table with 2-1/2" manual up-and-down adjustment. -- (4) Drive groups with 1 HP - 3,450 RPM drive motor each, timing belt & pulley drive. -- (6) Spindles, 2" in dia. and with Jacob chuck 0 - 1/2" capacity. -- Each boring group with independent vertical adjustment, spindle advancement powered by 3 HP hydraulic pump, -- 0" - 6" stroke, variable speed up to (30) strokes/Min. Complete with: --(3) Pneumatic holddowns. -- Cycle timer, automatic/manual foot pedal switch, and emergency stop.
Equipment Location:MIDWEST
Louis Sicotte
800-374-5009 ext:329
SICOTTE J 3H-5 Vertical Boring Machine -- 24" x 60" Table sizeEquiped with: -- (4) 1.5 HP motors mounted on 24" long arms with motor starter and overload relay -- (7) 1 1/2" Diameter spindle with spring collet 1/2" capacity -- (2) Spring loaded hold downs. -- (1) additional motor started with overload for future installation of spindle drive motorFeatures: -- 0" - 8" Vertical table feed, hydraulically operated, variable feed and table travel adjustable from front of machine, -- 3 HP hydraulic pump motor with reservoir. Complete with: -- Electrical control system with separate motor controls, -- Single or continous stroke, -- Manual and automatic cycle -- Foot pedal actuation -- (1) Safety guard.
Equipment Location:MIDWEST
Louis Sicotte
800-374-5009 ext:329
SICOTTE Model J-40-8 Combination Vertical/Horizontal Boring machine -- 24" x 96" Table size -- (4) Vertical Drive group with 2 HP motor, 1,800 RPM mounted on a 24" long cast iron arm including motor base with locking mechanism and timing belt drive. -- (4) Horizontal Drive group with 2 HP motor, 1,800 RPM with motor base and timing belt drive. On Vertical -- (1) Dovetail beam 2 7/8" X 96" long, with the main beam the spindle are always in a straight line -- (8) Vertical spindle 2" diam, with Jabob chuck 0" to 1/2" capacity that are monted on the dovetail beam, minimum center distance betwen spindle is 2". -- (2) Spring loaded vertical holddowns -- Vertical stoke of 8" with variable speed feedOn Horizontal -- (8) Horizontal spindle 2" diam. with jacob chuck 0" to 1/2" capacity , min. center distance between spindles is 2". -- (2) Pneumatic hold down for horizontal -- 3 HP hyrdaulic power unit for table movement -- Horizontal stoke of 6" with variable speed feed. Equipped with: -- Manual and automatic cycle for single or continous stroke. -- The horizontal and vertical cycle can be done simulteanously or independently -- Magnetic starters with overload protection & foot pedal cycle activation.
Equipment Location:EASTERN CDN
Louis Sicotte
800-374-5009 ext:329
SICOTTE/DOUCET T-1000 Vertical Boring Machine -- (3) Spindles with a center distance of 1-1/2" to 12". -- 2HP drive motor (3,450 RPM), 6" adjustable boring stroke. -- (2) Spring hold downs that cover the 12" of the table. -- Complete with: 5" wide X 48" long solid wood table. -- 1/2" capacity Spring collets. -- Operates with single or continuous strokes & manual or automatic cycles.
Equipment Location:MIDWEST
Louis Sicotte
800-374-5009 ext:329
SICOTTE/DOUCET T-1000 Vertical Boring Machine -- (3) Spindles with a center distance of 1-1/2" to 12". -- 2HP drive motor (3,450 RPM), 6" adjustable boring stroke. -- (2) Spring hold downs that cover the 12" of the table. -- Complete with: 5" wide X 48" long solid wood table. -- 1/2" capacity Spring collets. -- Operates with single or continuous strokes & manual or automatic cycles.
Equipment Location:MIDWEST
Louis Sicotte
800-374-5009 ext:329
Sicotte T 1050 Horizontal boring machine2-Spindle Horizontal Borer equipped with:1 HP Motor timing belt drives with motor starter.(2) horizontal spindles 1 1/2" diam. with spring collet 1/2" capacity turning at 3,450 RPM.Features: 4" Boring head stroke with air/oil system and adjustable feed speedSpindle mount on dovetail beam with minumim 1-1/2" to a max. 11 3/4" center distance.Complete with: (2) Pneumatic holddowns & 12" x 16" wooden table size.
Equipment Location:EASTERN CDN
Louis Sicotte
800-374-5009 ext:329
SICOTTE T 1050 Horizontal Boring Machine 2-Spindle Horizontal Borer.Equipped with: -- 2 HP Motor timing belt drives with motor starter. -- (2) Horizontal spindles 2" diam. with spring collet 1/2" capacity turning at 3,450 RPM.Features: -- 4" Boring head stroke with air/oil system and adjustable feed speed -- Spindle mount on dovetail beam with minimum 2" to a max. 11 3/4" center distance.Complete with: -- (2) Pneumatic holddowns & 12" x 16" wooden table size.
Equipment Location:NORTHEAST
Louis Sicotte
800-374-5009 ext:329
Richland and Shop Made Drill Press
Equipment Location:Florence, AL
LPS Equipment & Acquisition Co.
731-986-4351