You Have Selected

 
 
  • Used
  • New
 
  •  
 
  •  
 
  •  
 

 
1028 Results Found for Woodworking Viewing 1 - 20 of 1028 results
RECENTLY ADDED
PREMIUM LISTINGS

Yates Boardmaster Planer

Call for Price
Yates American A15 Boardmaster 12 Knife Planer w/Side Double Profile S/N B29747 w/Motorized Hydraulic, Infeed Table, electrical. Located in WI.
Equipment Location:Clarksburg, TN
LPS Equipment & Acquisition Co.
731-986-4351
STANDARD LISTINGS
BUTFERING SGO 109K Wide Belt Sander (1) Single Head -- 37" width cap. Combination Head --Head Configuration: -- Combination sanding head with steel contact roll & platen, 18 HP motor. -- (2) Abrasive belt speeds of 14 & 28 FPS; abrasive belt size 38" x 75", with air tensioning and electronic abrasive belt tracking. -- 4-double supported jack screws supporting table. -- Conveyor belt feed with 2 HP 2-speed drive, infeed & outfeed rubber covered holddown rolls -- 1/8" - 5-1/2" powered opening adjustment via joystick with LED readout. -- Complete with: Electric brake, (1) 6-1/4" dia. dust outlet; emergency stop button, motor load meter, magnetic controls, and numerous safety features.
Equipment Location:MIDWEST
Ed Webb
800-374-5009 ext:377
BUTFERING OPTIMAT 5BC-311-RCE Wide Belt Sander, (3) Heads;43" Width cap., Drum, Combination Head and Platen.Head Configuration: -- 1st Head: Steel Contact Drum with 25 HP motor. -- 2nd Head: Combination head with Drum and Segmented Platen, 20 HP motor. --3 rd. Head: Electronically controlled Air Segmented Finishing Platen, with 17 HP motor. Specifications: -- The contact roll height position with programmable control. -- The Finishing Platen consists of 35 mm segments designed to conform to part size to minimize sand through. -- 43" x 75" Abrasive belts and Electronic abrasive belt tracking, -- Contact Rolls with grit compensation adjustment.Feed System: -- Variable conveyor belt feed, feed speed of 8 - 43 FPM and with Automatic conveyor belt tracking. -- Vacuum conveyor belt to hold smaller parts, 3 HP feed drive; infeed & outfeed spring loaded, rubberized holddown rolls. -- 1/8" - 5-1/2" Motorized thickness adjustment with LED readout, -- Automatic part thickness setup with indexing control. -- Equipped with: Infeed panel "over-thickness" sensor.Equipped with & Features: -- Electronic motor brakes on sanding heads. -- Infeed & outfeed emergency stops, safety interlocks on all doors. -- Includes: Roller infeed conveyor extension and motor load meters.
Equipment Location:MID ATLANTIC
Joe Retzlaff
800-374-5009 ext:348
C.R. ONSRUD PANEL PRO 145G18D Moving Gantry CNC Router with ATC & Boring;5' x 12' Worktable, 11" Z-axis stroke; machined table with (3) multi-vacuum zones, moving gantry bridge and vertical supports.Equipped with: -- (1) 4-Pole 18 HP "HSK-63F" Electro Spindle, infinitely programmable spindle speeds up to 24,000 RPM, 12-position ride along ATC tool changer. (1) 9 spindle vertical drilling unit. -- Closed loop brushless AC Servo motors drive dual helical rack & pinion on the moving grantry & precision ball screws on the bridge & vertical axes; 2,000 IPM max. machining speed (straight or contour), 2,800 IPM max. traverse speed. -- All axes ride on extra large precision contour linear guideways, axis travels provide full table coverage.Controller & Operator Interface: -- Industrial "OSAI" Machine Control System is compatible with virtually all CAD/CAM packages that generate standard M & G code. -- Featuring: Simultaneous 4-axis motion, 32-bit RISC processor; 4-port Ethernet connection, inch/metric operation and feed rate & spindle speed override. -- Complete with: (3) BECKER Vacuum Pump on rack, assorted tool holders with collets, manuals and documentation.
Equipment Location:MID ATLANTIC
Norm Schust
800-374-5009 ext:445
C.R. ONSRUD 144G10 5 X 12 with ATC:Moving gantry CNC Router with a 144" x 60" worktable in a front-to-back configuration, machined Phenolic vacuum plenum with (3) zones; cast iron moving gantry bridge & vertical supports. -- Equipped with: (1) 10 HP "ISO-30" Type ATC spindle with side mounted 8-position carousel and infinitely programmable spindle speeds from 0 - 18,000 RPM. -- Drive system:Closed loop brushless AC Servo motors drive rack & pinion on both sides of the gantry and precision ball screws on the bridge & Z-axis; all axes ride on extra large THK precision contour linear guideways. -- Upgraded Control by Power Automation:Industrial "Centroid" PC Front End" Machine control system is compatible with virtually all CAD/CAM packages that generate standard M & G codes; built into "Roll Around" Pedestal console.. -- Featuring:Simultaneous 3-axis motion, 32-bit RISC processor w/115,000 baud rate download capability; RS-232 port, inch/metric operation, and feed rate & spindle speed override. -- Complete with:25 HP QUINCY Vacuum System, assorted tool holders with collet & cover nut, and documentation.
Equipment Location:MIDWEST
Norm Schust
800-374-5009 ext:445
CADORET MANUAL FINGER JOINT SYSTEM: -- Shaper Sections includes right and left hand Shaper Units, each with AC variable speed drives from 30 to 60 FPM. Shapers with hand-wheels and digital readout scales; on on the horizontal saw adjustment and one each on vertical and horizontal spindle adjustments, Retractable guide knives for running flooring; quick change chain lug back up blocks for end matching; extended arm for running up to 16' long material; roller track for material longer than 48". -- APQUIP Glue Applicator on second Shaper. -- 20' Manual Press Section with 5/8" to 3" thickness cap; 3/4" to 8" width cap.; 36" to 240" assembled length capacity. With hydraulic driven rubber rolls and adjustable length stops. -- High efficiency motors used throughout.
Equipment Location:MIDWEST
Jeff Terrill
800-374-5009 ext:349
CALPE TH5-1600 Heavy-Duty High-Production, Fully Automatic CNC Lathe: General Description: Multi-Spindle cutting simultaneously, (5) spindles using V-type gouge knives; 63" (1,600 mm) max. distance between centers; 5-1/2" (140 mm) max. swing diameter between spindles. -- CNC Controlled with 3.35" (85 mm) travel for depth of cut. -- Motors/Speeds: (2) Head stock motors, each 12.5 HP - 1,750 RPM; CNC controlled electronic variable speed of main head from 100 - 6,000 RPM. 2 HP approx hydraulic drive. -- Fast return travel of up to 590 IPM (15,000 mm/min); CNC controlled feed speed carriage, variable up to 50 FPM (15 MPM). -- Loading device & tail stock powered by hydraulic pump with 2 HP - 1,750 RPM motor; No. 5 Morse taper on main spindle shaft. -- Features: Automatic loading & unloading device; carriage mounted with linear guides providing high precision movement. -- Full CNC controller with on-screen CAD programming for all products.Matching CALPE L6-1600 spindle sander is available at additional cost at same facility.
Equipment Location:NORTHEAST
Tony Cornacchione
800-374-5009 ext:432
CAMWOOD Model SM-236U Moulder Feed Through -- 6-Head (B-R-L-T-T-U), working cap. 9" x 4-3/4" -- Head sequence: Bottom 10 HP, Right 10 HP, Left 10 HP, Top 15 HP, Top 15 HP and Universal 7.5 HP motor. --SPECIFICATIONS --Max. (Min.) Working Thickness 4-3/4" (5/16") --Min. Working Length 9½" --Feed Motor 7½ HP --Elevation 1½ HP -- Spindle Dia.: 40 MM with cutterhead speed of 6,000. Mechanical digital readouts for all spindle adjustments, as well as chipbreakers and pressure elements. Tool cutting circles: vertical spindles 5" to 6.25" and top spindles 5" to 7". -- Variable Feed: From16 ~ 82 FPM with LED speed readout. Over sized top and bottom rollers run synchronized, ensuring smooth feeding. The three independent section pneumatic pressures for the infeed rollers, in-process rollers and outfeed rollers can be set with individual pressure allowing for consistent feeding. -- Universal spindle with 270° rotation form the left side. -- Includes: Infeed table 2M (6'6") with manual table lubrication ports. Side pressure roller at infeed; Hard chrome-plated table for maximum wear resistance. Full sound and safety enclosure and manuals. Optional: Short Stock Feed Package $900.00
Equipment Location:WEST COAST
Mark Green
800-374-5009 ext:332
CAM-WOOD AM-533 Wide Belt Sander, (3) Heads; 53" Width cap. and with Drum, Drum, Combination Head. - Monocoque shell type, nut and bolt free base, constructed in thick steel tube, electro-welded using robot technology to guarantee maximum rigidity and precision.Head Configuration: -- 1st Head: 241.3 mm (9.5") dia. steel roller. -- 2nd Head: 241.30mm (9.5") dia. calibrating/sanding roller with 80 Shore rubber coating. -- 3rd Head: 208.3 mm (8.2") dia. sanding roller with 70 Shore rubber coating, Stiff felt sanding with graphite cloth held in place by screws.Specifications: -- Working width 1,350 mm (53"). -- Sanding belt dims 1,346 mm x 2,184 mm (53" x 86"). -- Min. and max. material thicknesses 3 mm - 200 mm (1/8" - 7.8"). --Variable feed speed from 16-98 FPM 5 HP motor; automatic conveyor belt tracking. -- 1st Head 40 HP motor -- 2nd Head 30 HP motor. --3rd Head 25 HP motor -- Dust extraction hood 160 mm (6.3") diameter.Equipped with & Features: -- Conveyor bed raises & lowers by (4) heavy duty trapezoidal screws anchored externally to the base, supported by thrust bearings and coupled by means of stiffener bars to guarantee perfect alignment and stability. Rise & Fall motor 1 HP -- Electronic display of workpiece thickness. -- Support rollers: one at the infeed and one at the outfeed end of the conveyor bed. -- Rubber coated pressure rollers located before and after each of the sanding heads. -- Electronic sanding belt tracking system. --Rear panel brush cleaner -- Automatic Star Delta starter on main motors. -- Automatic brake on sanding head motors.
Equipment Location:MID ATLANTIC
Joe Retzlaff
800-374-5009 ext:348
CAM-WOOD - WR 408 VAC - CNC Router.Material processing dimensions of 49" x 98.4" x 8". -- Fixed 3-zone vacuum table, with vacuum pressure guage. The factory installed vacuum table is designed for nested based panel processing. -- Moving gantry bridge rides on high precision HIWIN linear rails for consistent movement and accurate cutting. -- Welded structural steel machine base provides a solid foundation for superior cut quality. -- The tool gantry and bridge travel by rack & pinion and the vertical axis travels on ball screws for smooth consistent movement. -- Industrial grade 3 HP direct drive router spindle, liquid cooled for cool & quiet running and extended life. -- Variable tool speed up to 24,000 RPM allows for the right cutting speed in any application. -- X- & Y-axis 1,500 IPM Traverse speed for quick movement between cutting cycles to reduce total CNC machining time. -- Windows based CNC Control is preloaded on a DELL PC with a 19" monitor (included); very intuitive interface, quick to learn and easy to use. -- CAM-WOOD PRO is a full featured machine operating system with on-screen tool path graphics. -- Compatible with virtually all CAD/CAM programming software on the market, which means you can choose the software that suits your business best. -- Includes a dust hood with 4" diameter inlet. Price Includes TRAVAINI "DYNASEAL EVO 10" Vacuum Pump, 10 HP, 230/460 V, 60 Cy, 3-Phase,
Equipment Location:MIDWEST, AL
EX-FACTORY INC.
704-841-2001
CAM-WOOD - KT2, ...Edgebander. Compact - Single Sided (mfg. in Italy);0.4 mm - 2 mm Max. edge thickness cap., 10 mm - 45 mm (1-3/4") panel thickness cap. (when edgebanding 2 mm PVC, max thickness is 22 mm or (3/4"). -- Equippped with: Automatic feed of coil banding and semi-automatic strip fed magazine (strips 1- 2 mm max.) with 2 mm PVC cap. guillotine. -- Teflon coated glue pot w/fast (10 - 12) Min heat-up time. -- Guillotine unit to cut edgebanding in coils up to 2 mm thick. -- Workstations: Single end trimming unit with pneumatic power knife to cut at 90° flush to the leading & trailing edges of the panel. -- Top & bottom High Frequency flush trims (0.46 HP - 12,000 RPM HF motors). -- Includes (2) 2 mm radius cutters. -- Feed Track & Speed: 0.35 HP Feed drive for a feed rate of 15 FPM; feed chain with rubberized surface of pads. -- Special design "track frame" to eliminate feed chain side-to-side movement after years of use. -- Rubberized holddown rollers with ball bearings for low friction and long life. -- Sound enclosure protects the operator from noise and debris.Engineered & Manufactured by TECNOMA S.r.l., Italy.
Equipment Location:MIDWEST
Ed Webb
800-374-5009 ext:377
CAM-WOOD KT2 SINGLE SIDED EDGEBANDER0.4 mm - 2 mm Max. edge thickness cap., 10 mm - 45 mm (1-3/4") panel thickness cap. (when edgebanding 2 mm PVC, max thickness is 22 mm or (3/4").Equippped with: Automatic feed of coil banding and semi-automatic strip fed magazine (strips 1- 2 mm max.) with 2 mm PVC cap. guillotine.Teflon coated glue pot w/fast (10 - 12) Min heat-up time.Guillotine unit to cut edgebanding in coils up to 2 mm thick.Workstations: Single end trimming unit with pneumatic power knife to cut at 90° flush to the leading & trailing edges of the panel.Top & bottom High Frequency flush trims (0.46 HP - 12,000 RPM HF motors).Includes (2) 2 mm radius cutters.Feed Track & Speed: 0.35 HP Feed drive for a feed rate of 15 FPM; feed chain with rubberized surface of pads.Special design "track frame" to eliminate feed chain side-to-side movement after years of use.Rubberized holddown rollers with ball bearings for low friction and long life.Sound enclosure protects the operator from noise and debris.Engineered & Manufactured by TECNOMA S.r.l., Italy.
Equipment Location:MIDWEST
Ed Webb
800-374-5009 ext:377
CAM-WOOD - KT3.4 RRS, ...Edgebander, Compact - Single-Sided (Mfg in Italy);0.4 mm - 3 mm Max. edge thickness cap., 10 mm - 40 mm panel thickness cap. (when edgebanding 3 mm PVC max.. thickness is 30 mm). -- Automatic feed of coil banding and semi-automatic strip fed magazine (strips 1 - 3 mm max..) with 3 mm PVC cap. guillotine. -- Teflon coated glue pot w/fast (10 - 12) Min heat-up time. -- Guillotine unit to cut edgebanding in coils up to 3 mm thick.Workstations: -- Single end trimming Saw unit using High Frequency motor. Cutting group moves on rounded ways made of hardened steel, to guarantee high precisoin and reliability. Cutting movement from the top of the panel is synchronized by the PLC control, adjustable copier prevents chipping. -- Top & bottom High Frequency Trim Station (0.46 HP - 12,000 RPM HF motors). Unit features - adjustable copying on vertical & horizontal floating movements, adjustable cutting position by mechanical digital indicator, quick release (electrical & mechanical). -- Includes (2) 3 mm radius cutters. -- Top & Bottom 3 mm Super-Finish PVC/ABS Scrape station with quick working exclusion of both top & bottom units, micrometer adjustment; features thick chrome plated copying shoes, body of unit is cast iron to ensure vibration free scraping during operation. -- Top & Bottom Buffing unit 0.13 kW (0.17 HP - 2,800 RPM) motors.Features: -- 0.35 HP Feed drive for a feed rate of 26 FPM; feed chain pads with replaceable rubberized surface inserts. -- Special design "track frame" to eliminate feed chain side-to-side movement after years of use. -- Rubberized holddown rollers with ball bearings for low friction and long life. -- Sound enclosure protects the operator from noise and debris.Engineered & Manufactured by TECNOMA S.r.l., Italy.
Equipment Location:MIDWEST
Ed Webb
800-374-5009 ext:377
CAM-WOOD - KT3.4 RRS, ...Edgebander. Compact - Single Sided (mfg. in Italy).0.4 mm - 3 mm Max. edge thickness cap., 10 mm - 40 mm panel thickness cap. (when edgebanding 3 mm PVC max. thickness is 30 mm). -- Automatic feed of coil banding and semi-automatic strip fed magazine (strips 1 - 3 mm max.) with 3 mm PVC cap. guillotine. -- Teflon Coated glue pot w/fast (10 - 12) Min heat-up time. -- Guillotine unit to cut edgebanding in coils up to 3 mm thick.Workstations: -- Single end trimming Saw unit using High Frequency motor. Cutting group moves on rounded ways made of hardened steel, to guarantee high precisoin and reliability. Cutting movement from the top of the panel is synchronized by the PLC control, adjustable copier prevents chipping. -- Top & bottom High Frequency Trim station (0.46 HP - 12,000 RPM HF motors). Unit features - adjustable copying on vertical & horizontal floating movements, adjustable cutting position by mechanical digital indicator, and quick release (electrical & mechanical). -- Includes (2) 3 mm radius cutters. -- Top & Bottom 3 mm Super Finish PVC/ABS Scrape station with quick working exclusion of both top & bottom units, micrometer adjustment; features thick chrome plated copying shoes, body of unit is cast iron to ensure vibration-free scraping during operation. -- Top & Bottom Buffing unit with 0.13 kW (0.17 HP - 2,800 RPM) motors.Features: -- 0.35 HP Feed drive for a feed rate of 26 FPM; feed chain pads with replaceable rubberized surface inserts. -- Special design "track frame" to eliminate feed chain side-to-side movement after years of use. -- Rubberized holddown rollers with ball bearings for low friction and long life. -- Sound enclosure protects the operator from noise and debris.Engineered & Manufactured by TECNOMA S.r.l., Italy.
Equipment Location:MIDWEST
Ed Webb
800-374-5009 ext:377
CAM-WOOD AM-24 Top & Bottom Planer:24" Capacity planer with Spiral Heads for accurate and powerful two-sided planing in one pass.Features & Design: -- The work table surface was precision ground and then electro chrome plated and polished to smooth mirror finish. -- A heavy duty feed conveyor with metal spikes firmly holds stock securely to the work table. -- A stepless variable speed control for smooth adjustment of feed. -- The infeed conveyor, fitted with numerous pressure pins, will moderately press the stock, and then accurate planing surface can be performed to prevent jumping. -- The (4) power feed rollers are driven with a geared transmission box linked with heavy-duty drive chain and gears. -- A twist torsion anti-kickback device provides additional safety. It safeguards mechanical parts in case of overload. -- A ½ HP motor is utilized to quickly & conveniently make adjustments in thickness when setting the upper cutter head.Technical Specifications: -- Max. Planing Width: 24" -- Max. planing thickness: 6-5/8" -- Max. cutting depth: 1/4". -- Min.Planing length: 10". -- Feed speed, variable, 10 - 50 FPM. -- Cutterhead speed: 4,200 RPM. -- Upper motor 30 HP & Lower motor 15 HP. -- Feed motor: 5 HP and Elevation motor: 1/2 HP. -- Table size: L 93" x W 24" -- Weight: 6,950 LbsThe heavy duty rigid cast iron frame supports the work table and helps dampen vibration and ensures years of dependable service.
Equipment Location:WEST COAST
Jeff Terrill
800-374-5009 ext:349
CAMERON AUTOMATION OPTI-MATCH Color Matching-Panel Sizing- Optimization SystemFEATURES: ● Accurately measure board width and color from parallel ripped defected stock. ● Scan an area 5" in from the end of each board as it traverses across grain. ● Choose from 22 boards at a time to find boards that are close in color to make a specified size panel. ● Assemble the chosen boards in the proper order to blend the boards in each panel. ● Automatically stack the assembled panels on a scissors lift, ready for gluing. ● Keep accurate tallies of panels and board pieces. ● Allow entering of multiple panel widths. ● Smart stack multiple panel widths.Machine Dimensions:: ● Overall Height: 54" (1372 mm) ● Overall Width: 54 1/2" (1384 mm) ● Overall Length: 27’ 2" (8.28 Meters) ● Specifi cations: ● Minimum Board Length: 10” (254 mm) ● Maximum Board Length: 48” (1250 mm) ● Maximum Board Width: 6” (152 mm) ● Minimum Board Width: 1” (25.4 mm) ● Maximum Thickness: 8/4” (51 mm) ● Maximum Panel Width: 36” (914 mm)Actual model is 35A-M4This machine has approx 4,500 hours of running
Equipment Location:MIDWEST
Jeff Terrill
800-374-5009 ext:349
CAMERON AUTOMATION OPTI-MATCH Color Matching-Panel Sizing- Optimization SystemFEATURES: ● Accurately measure board width and color from parallel ripped defected stock. ● Scan an area 5" in from the end of each board as it traverses across grain. ● Choose from 22 boards at a time to find boards that are close in color to make a specified size panel. ● Assemble the chosen boards in the proper order to blend the boards in each panel. ● Automatically stack the assembled panels on a scissors lift, ready for gluing. ● Keep accurate tallies of panels and board pieces. ● Allow entering of multiple panel widths. ● Smart stack multiple panel widths.Machine Dimensions:: ● Overall Height: 54" (1372 mm) ● Overall Width: 54 1/2" (1384 mm) ● Overall Length: 27’ 2" (8.28 Meters) ● Specifi cations: ● Minimum Board Length: 10” (254 mm) ● Maximum Board Length: 48” (1250 mm) ● Maximum Board Width: 6” (152 mm) ● Minimum Board Width: 1” (25.4 mm) ● Maximum Thickness: 8/4” (51 mm) ● Maximum Panel Width: 36” (914 mm)Also included: scissor lift 24" X 48"This machine has new camera and laptop replace 3 years ago
Equipment Location:EASTERN CDN
Jeff Terrill
800-374-5009 ext:349
CANTEK SS 512 T Tilting Spindle Shaper5 HP - 3-Phase motor, -- 31-1/2" x 39" fixed table with dovetail slot; spindle stroke 5-1/2"; 1-1/4" dia. spindle with 5 MT receiver and 4-3/4" cap. under the nut. -- Tilting from -5° to + 45°. -- (5) Spindle speeds: 3,000, 4,000, 6,000, 8,000 & 10,000 RPM.³ -- Complete with: Spindle reversing switch, micro-adjustable fence 6" x 43", thermal overload protection and dust hood and toolbox
Equipment Location:WESTERN CDN
Torry Hiddema
800-374-5009 ext:371
CANTEK C-12RSH Straight Line Rip Saw With DOUCET BTRS 70 Return Conveyor --Ruggedly constructed with cast iron & ground tables, cast iron pressure housing with (6) guide rollers and solid welded steel base chassis. Specifications: --Saw blade dia. 8" - 12", saw arbor dia. 1", saw arbor speed 4,400 RPM, 15 HP saw arbor motor. -- 1 HP feed motor, 45 - 120 FPM variable speed range, min. workpiece length 8" -- Max. cutting thickness 3-3/8", distance from column to center of chain 18", Table size 39" x 57". Table height, 31-1/2" -- The cast iron upper pressure housing provides a stable mounting for the precision ground & nickle chrome steel saw arbor and can be easily adjusted by hand wheel for thickness changes. -- 1-piece cast iron chain with a diamond cut surface for positive material feeding.Doucet BTRS 70 --Line shaft powered roller (PVC covered) LEFT-HAND Return Conveyor System. Automatically receives-and-transfers parts with (7) transfer bands onto the return side. -- Receiving table: 30" W x 60" L. --Belt transfer width: 42" -- Return conveyor: 12" W x 102" L. (Over-all dimensions of receiving/transfer/return section is 60" long x 74" wide + 102" long powered line shaft roller return section). -- Variable Speed conveyor from 40 - 120 FPM, belt transfer speed 180 FPM. -- Automatically receives, transfers and conveys parts back to the operator
Equipment Location:EASTERN CDN
Joe Retzlaff
800-374-5009 ext:348
CANTEK TOP & BOTTOM HEAD SURFACER WITH THE FOLLOWING FEATURES AND EQUIPMENT: -- 18" x 6" Cap., mmn. thickness 3/8" -- Powered by 20 HP top & 15 HP bottom head motors: belt driven helical spiral cutterheads @ 6,000 RPM; each head features (6) rows of 4-sided carbide inserts. -- Variable feed speeds from 23 - 52 FPM powered by a 3 HP motor; tables are hard chrome plated and precision ground for maximum wear resistance. -- (2) Sets of 4" dia. upper pneumatic tensioned rollers, (1) 4" dia. powered top outfeed roller, (1) non-powered 4" dia. bed roller & caterpillar feed chain system with an auto-adjustment device to prevent damage due to improper tension. -- Power raise and lower of table guided by (4) gib-guided post screws via a 1/2 HP motor. The transmission system is directly driven by flexible shafts for high accuracy; PC control for fine adjustment of thickness control. -- Complete with: Control panel with push button controls and LED readouts for height & speed adjustments. -- Emergency stop button on feed control.
Equipment Location:SOUTHWEST
Jeff Terrill
800-374-5009 ext:349