You Have Selected

 
 
  • Used
  • New
 
  •  
 
  •  
 
  •  
 

 
1324 Results Found for Woodworking Viewing 1 - 20 of 1324 results
RECENTLY ADDED
STANDARD LISTINGS
ECO SENSORS MODEL C-21 VOC GAS SENSOR.Continuously monitors VOC's in a work environment. Detects leaks and poor air quality for Woodworkers, Spray Booths, Paint Shops, Chemical Production Areas, and anywhere indoor air quality monitoring is necessary. Assists in compliance with VOC air quality regulations for hydrocarbon gases and solvent vapors. -- Includes: Built-in Audio Alarm. Provision for External Alar, or Data Logger. Battery operation. -- Features and Benefits: Monitors and Alarms below OSHA TLV for most common solvent based VOC's before they become a health hazard. -- Highly sensitive to VOC's and solvents with bright Green-Yellow-Red display clearly indicates hazard levels of gases and vapors. -- Detects down to OSHA, EPA, and other regulatory bodies for mandated levels; typically at low ppm concentrations. -- Easy to use and understand; virtually maintenance free; built-in rechargeable battery for portable use in finding leaks. Includes many safety features. -- Specifications: Scale of 50 - 100 ppm for most solvent based VOC's. -- Color Coded Bar Indicator: Green = Normal; Yellow = Caution; Red = Danger. -- Responds within seconds of VOC gas reaching the sensor on device. -- Power Requirements: 12 VDC @ 300 mA rechargeable battery. 110V AC adapters available world wide. Self-contained NiCad or NiMH battery; approx. 2 hr capacity and recharged by AC adapter overnight. -- Dimensions: 3.25" x 1.375" x 2.375". Approx. weight 5 oz.
Equipment Location:WEST COAST
Tony Varda
800-374-5009 ext:335
EKSTROM CARLSON Model EE Straight Line Rip Saw; Specifications: -- 30 HP Saw arbor motor. -- Maximum thickness 3¼” with 16” dia. saw blade (no blade). -- 5 HP Feed Motor with feed rates infinitely variable to 280 FPM. -- Triple lower infeed rollers are chain driven and are adjustable from zero to 5°. -- Elongated pressure bar housing assures the proper guidance across the entire table length.Equipped with & Features: -- Spring loaded rollers with one inch yield. -- Dual position and lubrication system, two outfeed rollers. -- Please note: Chain appears to be in very good condition.
Equipment Location:PACIFIC NORTHWEST
Joe Retzlaff
800-374-5009 ext:348
EMC SMART 300 1K Calibrating Sander, (1) Sanding Head, Combi Roller and PadTECHNICAL DATA: -- Useful working width 300 mm (11-3/4"). -- Working thickness min/max mm 3 - 180 (1/8" - 7"). -- Abrasive belt dimensions, (length) 1,900 mm (75") x (width) 320 mm (12-1/2"). -- (2) Speed Feed belt speed 4 and 8 m/Min. (13 and 26 FPM). 1st Working Unit: Combination Roller & Pad. Roller diameter 125 mm (5"). Rubber covered hardness 85 Shore. Roller pressure adjustment control and grit-set system. 5.5 kW (7.5 HP) Main Motor. On Off Selector control with pneumatic piston to select roller. PNEUMATIC Flexible Sanding Pad Including On-Off Selector: Quick Change System: Removable pad with felt, rubber and graphite. Rotating cutting speed 16 m/Sec (53 FPS). Abrasive belts oscillation by means of electronic photocell sensor. Idle table rollers support in infeed and outfeed.Work Table: Manual lifting an lowering including fine adjustment. Natural rubber conveyor belt, machined. Feed belt centering by means of conical rollers. Mechanical digital display for working thickness; resolution 0.1 mm (0.004")Centralized Control Cabinet: IP 54 protection. Analog ammeter on main control cabinet. Centralized independent pneumatic control cabinet: IP 54 protection. Pneumatic air filter with automatic water-drain system. Pneumatic adjustment for "Grit set system". Pneumatic plant working without lubrication. Compressed air pressure 6 bar (85 PSI) Features: Control panel with self-diagnostics alarm control unit, Rubber covered presser rollers, grooved.UL Safety Norms
Equipment Location:MIDWEST
Ed Webb
800-374-5009 ext:377
EMC SMART 300 2RR Calibrating Sander, (2) Sanding Heads: Roller, RollerTECHNICAL DATA: -- Useful working width 300 mm (11-3/4"). -- Working thickness min/max mm 3 - 180 (1/8" - 7"). -- Abrasive belt dimensions, (length) 1,900 mm (75") x (width) 320 mm (12-1/2"). -- (2) Speed Feed belt speed 4 and 8 m/Min. (13 and 26 FPM). 1st Working Unit: Roller diameter 125 mm (5"). Rubber covered hardness 85 Shore. Roller pressure adjustment control and grit-set system.(1) 7,5 kW (10 HP) Main Motor shared by the two working groups. On Off Selector control with pneumatic piston to select roller. Rotating Speed 16 m/Sec. (52.5 FPS).2nd Working Unit: Roller diameter 125 mm (5"). Rubber covered hardness 45 Shore. Roller pressure adjustment control and grit-set system. Rotating Speed 16 m/Sec. (52.5 FPS).Work Table: Manual lifting and lowering including fine adjustment. Natural rubber conveyor belt, machined. Feed belt centering by means of conical rollers. Mechanical digital display for working thickness; resolution 0.1 mm (0.004").Centralized Control Cabinet: IP 54 protection. Analog ammeter on main control cabinet. Centralized independent pneumatic control cabinet: IP 54 protection. Pneumatic air filter with automatic water-drain system. Pneumatic adjustment for "Grit set system". Pneumatic plant working without lubrication. Compressed air pressure 6 bar (85 PSI). Features: Control panel with self-diagnostics alarm control unit, Rubber covered presser rollers, grooved.UL Safety Norms
Equipment Location:MIDWEST
Joe Retzlaff
800-374-5009 ext:348
Compact Straight-Line Rip Saw with a guaranteed 8' glue line. -- Powered by a 15 HP direct drive motor. -- Equipped with a Wye-Delta soft start for lower amp requirements during start-up. -- Heat treated chain and raceway with automatic oiler. -- All SQUARE D electrical controls. -- Large 14-3/4" rip capacity. -- Overarm control box mounted on the in-feed side. -- Total space requirements are about the same as a standard size tablesaw. -- Options: Return conveyor, powered outfeed roller, "XL-10XR" Laser light with mounting bracket, digital readout kit, wired for 460 Volt / 3-Phase.
Equipment Location:SOUTH
Joe Retzlaff
800-374-5009 ext:348
E M C SOLID SURFACER 1350 3RRRR... Corian Sander with (4) Sanding Heads, all Contact Rollers.This machine is developed for the processing of CORIAN. The SOLID SURFACER is for calibrating, grinding and pre-finishing. In combination with the EMC R-evo the final superfinish is accomplished. For detailed information on the R-evo please see our listing # SX-300047.Useful working width 1,350 mm (53"). Working thickness min./max. 3 - 170 mm (1/8" - 6-11/16"). Head configuration:1st Head: Roller "R", Belts dimensions: 2,620 x 1,320 mm (103" x 52"). -- Roller diameter 190 mm (7-1/2"). -- Roller rubber hardness 85 Shore. -- Constant control to any position with accuracy 0.02 mm. -- "Grit-set system" for abrasive belt grit compensation, pneumatically operated. -- On-Off selector, pneumatically operated. -- Motor power: 15 kW (20 HP) with Automatic star-delta starter. -- Abrasive Belt cutting speed infinitely adjustable 3 to 19 m/Sec (10 to 62 FPS) with inverter. -- Rotation: Against feed (clockwise). -- Air Jet Blower for abrasive belt cleaning. -- Electronic oscillation of abrasive belt by sensor.2nd Head: Roller "R", Belts dimensions: 2,620 x 1,370 mm (103" x 54"). -- Roller diameter 190 mm (7-1/2"). -- Roller rubber hardness 65 Shore. -- Constant control to any position with accuracy 0.02 mm. -- "Grit-set system" for abrasive belt grit compensation, pneumatically operated. -- On-Off selector, pneumatically operated. -- Motor power: 11 kW (15 HP) with Automatic star-delta starter. -- Abrasive Belt cutting speed infinitely adjustable 3 to 19 m/Sec (10 to 62 FPS) with inverter. -- Rotation: Against feed (clockwise). -- Air Jet Blower for abrasive belt cleaning. -- Electronic oscillation of abrasive belt by sensor.3rd Head: Roller "R", Belts dimensions: 2,620 x 1,370 mm (103" x 54"). -- Roller diameter 190 mm (7-1/2"). -- Roller rubber hardness 45 Shore. -- Constant control to any position with accuracy 0.02 mm. -- "Grit-set system" for abrasive belt grit compensation, pneumatically operated. -- On-Off selector, pneumatically operated. -- Motor power: 11 kW (15 HP) with Automatic star-delta starter. -- Abrasive Belt cutting speed infinitely adjustable 3 to 19 m/Sec (10 to 62 FPS) with inverter. -- Rotation: Against feed (clockwise). -- Air Jet Blower for abrasive belt cleaning. -- Electronic oscillation of abrasive belt by sensor.4th Head: Roller "R", Belts dimensions: 2,620 x 1,370 mm (103" x 54"). -- Roller diameter 190 mm (7-1/2"). -- Roller rubber hardness 30 Shore. -- Constant control to any position with accuracy 0.02 mm. -- "Grit-set system" for abrasive belt grit compensation, pneumatically operated. -- On-Off selector, pneumatically operated. -- Motor power: 11 kW (15 HP) with Automatic star-delta starter. -- Abrasive Belt cutting speed infinitely adjustable 3 to 19 m/Sec (10 to 62 FPS) with inverter. -- Rotation: Against feed (clockwise). -- Air Jet Blower for abrasive belt cleaning. -- Electronic oscill
Equipment Location:MIDWEST
Joe Retzlaff
800-374-5009 ext:348
EMC VENUS 1100 SUPER 2RK Finishing Sander with (2) Sanding Heads: Roller and Combination Head.Useful working width 1,100 mm (51"). Working thickness min/max mm 3 - 170 (1/8" - 6-5/8").SUPER indicates longer belt length of 2,620 mm (103").Head configuration:1st Head: Roller "R" Belt dimensions: 2,620 x 1,320 mm (103" x 52"). Roller diameter: 190 mm (7-1/2"). Roller rubber hardness 85 Shore. On/off selector pneumatically operated. "Grit-set system" for grit compensation. Constant control to any position with accuracy 0.02 mm. Rotation: Against feed (clockwise). Motor power: 22 kW (30 HP). Automatic star-delta starter. Rotating cutting speed: 21 m/Sec (68 FPS). Blower for the roller unit.2nd Head: Combination Roller & Pad "K". Belt dimensions: 2,620 x 1,320 mm (103" x 52"). Roller diameter 142 mm (5-5/8"). Rubber covered hardness 45 Shore. Roller pressure adjustment control & "grit-set system" for grit compensation. Fine sanding pad is pneumatically controlled. Motor is shared with the above unit. Rotating cutting speed: 18 m/Sec (59 FPS). Quick Change System for removable pad with felt.Electronic segmented Sanding Pad "CP" with 37 segments, each 29,7 mm wide (1-3/16"). Including On-Off Selector: . Rotating cutting speed 18 m/Sec (59 FPS). Abrasive belts oscillation by means of electronic photocell sensor.Machine management system: Electronic colour 7" Touch Screen control & display. PLC with micro-processor - CP0291. Connection for USB, RS232, Ethernet 10/100/1000. Storage capacity of 100 sanding programs. Front protection IP65 against dust & moisture.Feed system: -- MOBILE WORK TABLE. -- Idle table rollers support in infeed and outfeed. -- Rubber covered presser rollers, grooved. -- Variable feed belt speed, adjustable from 3 to 19 m/Min (9.8 - 62 FPM) Inverter Controlled. -- Large diameter screws on machined guides with columns and pistons. -- Automatic feed belt centering device.General Machine Features: -- Analog ammeters, for each motor, on main control cabinet. -- Electronic motorized grit set system, control from touch screen for each head.Electronical Panel: -- Check Control Self Diagnostics with Alarm Control. -- Analog Ammeters, for each motor, on the main control cabinet. -- Electronic raising and lowering of the table, thickness system, electronically controlled. -- Independent Overload protection.Safety: -- Infeed front emergency swinging bar for oversized panels. -- Infeed protection pressing blade to avoid pieces to go back to operator. -- Rear and front emergency push buttons. -- Automatic brake on abrasive belts motors. -- Automatic emergency stop and alarm display in case of: -- Low Air Pressure. -- Doors opened ("easy maintenance and inspection"). -- Electric motors overloading. Emergency detector for over thickness material cut. -- No tension on abrasive belt. -- Abrasive belt lateral mistracking. -- Abrasive belt broken. -- Idle table rollers support in infeed and outfeed -- Selector Switches on both
Equipment Location:MIDWEST
Joe Retzlaff
800-374-5009 ext:348
EMC VENUS 1100 SUPER 3RRR Finishing Sander with (3) Sanding Heads: Roller - Roller - Roller.Useful working width 1,100 mm (43"). Working thickness min/max mm 3 - 170 (1/8" - 6-5/8").SUPER indicates longer belt length of 2,620 mm (103").Head configuration:1st Head: Roller "R" Belts dimensions: 2,620 x 1,120 mm (103" x 44"). -- Contact Roller diameter: 190 mm (7-1/2"). Roller rubber hardness 85 Shore. Constant control to any position with accuracy 0.02 mm. "Grit-set system". Rotation: Against feed (clockwise). Motor power: 22 kW (30 HP). Automatic star-delta starter. Rotating cutting speed: 21 m/Sec (68 FPS). Blower for the roller unit.2nd Head: Roller "R" Belts dimensions: 2,620 x 1,120 mm (103" x 44"). -- Contact Roller diameter: 190 mm (7-1/2"). Roller rubber hardness 65 Shore. Constant control to any position with accuracy 0.02 mm. Rotation: Against feed (clockwise). Motor power: 15 kW (20 HP). Automatic star-delta starter. Rotating cutting speed: 21 m/Sec (68 FPS). Blower for the roller unit.3rd Head: Roller "R" Belts dimensions: 2,620 x 1,120 mm (103" x 44"). -- Contact Roller diameter: 220 mm (8-11/16"). Roller rubber hardness 45 Shore. Constant control to any position with accuracy 0.02 mm. Anti-dubbing including pneumatic piston. Rotation: Against feed (clockwise). Motor is shared with the above unit. Rotating cutting speed: 21 m/Sec (68 FPS). Blower for the roller unit.Feed system:MOBILE WORK TABLEVacuum conveyor beltIdle table rollers support in infeed and outfeedRubber covered presser rollers, groovedVariable feed belt speed, adjustable from 3 to 19 m/Min (9.8 - 62 FPM) Inverter ControlledMotorized table movement with fine adjustment on 4 precision screws Automatic feed belt centering deviceElectronic digital display for thicknessGeneral Machine Features: -- Analog ammeters, for each motor, on main control cabinet. -- Electronic motorized grit set system, control from touch screen for each working group.Electronical Panel: -- Check Control Self Diagnostics with Alarm Control. -- Analog Ammeters, for each motor, on the main control cabinet. -- Electronic raising and lowering of the table, thickness system, electronically controlled. -- Independent Overload protection.Safety: -- Infeed front emergency swinging bar for oversized panels. -- Infeed protection pressing blade to avoid pieces to go back to operator. -- Rear and front emergency push buttons. -- Automatic brake on abrasive belts motors. -- Automatic emergency stop and alarm display in case of: -- Low Air Pressure. -- Doors opened ("easy maintenance and inspection"). -- Electric motors overloading. Emergency detector for over thickness material cut. -- No tension on abrasive belt. -- Abrasive belt lateral mistracking. -- Abrasive belt broken.Idle table rollers support in infeed and outfeedSelector Switches on both working units.Centralized Control Cabinet: IP 54 protection. Analog ammeter on main control cabinet. Table lifting-lowering thickness system e
Equipment Location:MIDWEST
Joe Retzlaff
800-374-5009 ext:348
EMC VENUS 1300 SUPER 1K Finishing Sander with (1) Sanding Head: Combination Head.Useful working width 1,300 mm (51"). Working thickness min/max mm 3 - 170 (1/8" - 6-5/8").SUPER indicates longer belt length of 2,620 mm (103").Working Unit: Combination Roller & Pad. -- Roller diameter 142 mm (5-5/8"). Rubber covered hardness 45 Shore. Roller pressure adjustment control. Main Motor On Off Selector control with pneumatic piston to select roller, 22 kW (30 HP) Automatic star-delta starter Rotating cutting speed: 18 m/Sec (59 FPS). -- PNEUMATIC Flexible Sanding Pad Including On-Off Selector: Quick Change System: Removable pad with felt, rubber and graphite. Rotating cutting speed 17 m/Sec (55.8 FPS). Abrasive belts oscillation by means of electronic photocell sensor.Feed system:MOBILE WORK TABLEIdle table rollers support in infeed and outfeedRubber covered presser rollers, groovedVariable feed belt speed, adjustable from 3 to 19 m/Min (9.8 - 62 FPM). Inverter ControlledLarge diameter screws on machined guides with columns and pistonsAutomatic feed belt centering deviceGeneral Machine Features: -- Independent main motors. -- Analog ammeters, for each motor, on main control cabinet. -- Electronic motorized grit set system, control from touch screen for each working group.Electronical Panel: -- Check Control Self Diagnostics with Alarm Control. -- Analog Ammeters, for each motor, on the main control cabinet. -- Electronic raising and lowering of the table, thickness system, electronically controlled. -- Independent Overload protection.Safety: -- Infeed front emergency swinging bar for oversized panels. -- Infeed protection pressing blade to avoid pieces to go back to operator. -- Rear and front emergency push buttons. -- Automatic brake on abrasive belts motors. -- Automatic emergency stop and alarm display in case of: -- Low Air Pressure. -- Doors opened ("easy maintenance and inspection"). -- Electric motors overloading. Emergency detector for over thickness material cut. -- No tension on abrasive belt. -- Abrasive belt lateral mistracking. -- Abrasive belt broken.Idle table rollers support in infeed and outfeedSelector Switches on both working units.Centralized Control Cabinet: IP 54 protection. Analog ammeter on main control cabinet. Table lifting-lowering thickness system electrically controlled. AUTOMATIC Delta - Star starter on abrasive belts motors. Centralized independent pneumatic control cabinet: IP 54 protection. Pneumatic air filter with automatic water-drain system. Pneumatic adjustment for "Grit set system". Pneumatic plant working without lubrication. Compressed air pressure 6 bar (85 PSI). Options Available: Tampico Brush natural fiber brush for cleaning of the pieces, diameter 150 mm (6"). Motor Power 1.1 kW (1.5 HP). $3,950
Equipment Location:MIDWEST
Ed Webb
800-374-5009 ext:377
Specially design return conveyor for straight line rip saws. -- Separates the good drop from the original product. -- Variable speed allows matching to the rip saw production.
Equipment Location:SOUTH
Joe Retzlaff
800-374-5009 ext:348
EXTREMA EXCESS XS-2A-37 Wide Belt Sander, (2) Head --37" Width cap. Drum, Roller platen --Head Configuration --1st Head: Contact drum 25 HP motor --2nd Head: Roller and Platen 20 HP -- Features --Dual display digital thickness controller w/ thousandths jog feature. --Omron electronic eye sanding belt tracking --Wye-delta soft start --Regal variable speed drive unit --Quality electrical controls by Square D --Quality pneumatic controls by Camozzi --Automatic conveyor belt tracking --Auto thickness device for easy set up --Over thickness safety device --Heavier construction and more features than any other in it's class --Mono block construction increases durability --Specification: --Max. width cap 37" --Feed motor 3 HP --Elevation motor 0.5 HP --Max. thickness 6" --Min. thickness 1/8" --Contact drum 1st head 8" dia. --Roller drom on 2nd head 4.75" dia. --CFM requirements 3600 --Feed speeds 15-50 FPM --Belt size 37" X 60" --Weight 4600 lbs --AMPS (220V / 460V ) 122/61
Equipment Location:SOUTH
Joe Retzlaff
800-374-5009 ext:348
EXTREMA EXCESS XS-2A-43 Wide Belt Sander, (2) Head --43" Width cap. Drum, Roller platen --Head Configuration --1st Head: Contact drum 30 HP motor --2nd Head: Roller and Platen 25 HP -- Features --Dual display digital thickness controller w/ thousandths jog feature. --Omron electronic eye sanding belt tracking --Wye-delta soft start --Regal variable speed drive unit --Quality electrical controls by Square D --Quality pneumatic controls by Camozzi --Automatic conveyor belt tracking --Auto thickness device for easy set up --Over thickness safety device --Heavier construction and more features than any other in it's class --Mono block construction increases durability --Specification: --Max. width cap 43" --Feed motor 3 HP --Elevation motor 0.5 HP --Max. thickness 6" --Min. thickness 1/8" --Contact drum 1st head 8" dia. --Roller drum on 2nd head 4.75" dia. --CFM requirements 4200 --Feed speeds 15-50 FPM --Belt size 43" X 60" --Weight 5100 lbs --AMPS (220 V / 460V ) 148/74.
Equipment Location:SOUTH
Joe Retzlaff
800-374-5009 ext:348
EXTREMA PERFORMA XS-2B-37 Wide Belt Sander (2) Heads -- 37" Width cap. Drum, Roller and platen --Head Configuration --1st Head: Contact drum 25 HP motor --2nd Head: Roller and Platen 20 HP --Features: --75” Belt Length --Available with 1 to 3 heads --Over thickness safety device --Infeed bed rollers --Digital thickness controller --Individual amp meters --Disc brakes on sanding heads --Telemecanique electrics --Camozzi pneumatics --Variable speed drive system --Mono-block construction to increase durability. --Specification: --Max. width cap 43" --Feed motor 3 HP --Elevation motor 0.5 HP --Max. thickness 6" --Min. thickness 1/8" --Contact drum 1st head 8" dia. --Roller drum on 2nd head 5" dia. --CFM requirements 3600 --Feed speeds 15-50 FPM --Belt size 37" X 75" --Weight 5700 lbs --AMPS (220 V / 460V ) 122/61.
Equipment Location:SOUTH
Joe Retzlaff
800-374-5009 ext:348
EXTREMA PERFORMA XS-2B-43 DUAL HEAD WIDE BELT SANDER43" Width cap. Drum, Roller and platen -- Head Configuration -- 1st Head: Contact drum 30 HP motor -- 2nd Head: Roller and Platen 25 HP -- Features: -- 75” Belt Length -- Available with 1 to 3 heads -- Over thickness safety device -- Infeed bed rollers -- Digital thickness controller -- Individual amp meters -- Disc brakes on sanding heads -- Telemecanique electrics -- Camozzi pneumatics -- Variable speed drive system -- Mono-block construction to increase durability. -- Specification: -- Max. width cap 43" -- Feed motor 3 HP -- Elevation motor 0.5 HP -- Max. thickness 6" -- Min. thickness 1/8" -- Contact drum 1st head 8" dia. -- Roller drum on 2nd head 5" dia. -- CFM requirements 4200 -- Feed speeds 15-50 FPM -- Belt size 43" X 75" -- Weight 6100 lbs -- AMPS (220 V / 460V ) 148/74.
Equipment Location:SOUTH
Joe Retzlaff
800-374-5009 ext:348
EXTREMA PERFORMA XS-2B-52 Wide Belt Sander (2) Heads -- 52" Width cap. Drum, Roller and platen --Head Configuration --1st Head: Contact drum 30 HP motor --2nd Head: Roller and Platen 30 HP --Features: --75” Belt Length --Available with 1 to 3 heads --Over thickness safety device --Infeed bed rollers --Digital thickness controller --Individual amp meters --Disc brakes on sanding heads --Telemecanique electrics --Camozzi pneumatics --Variable speed drive system --Mono-block construction to increase durability. --Specification: --Max. width cap 52" --Feed motor 3 HP --Elevation motor 0.5 HP --Max. thickness 6" --Min. thickness 1/8" --Contact drum 1st head 8" dia. --Roller drum on 2nd head 5" dia. --CFM requirements 4800 --Feed speeds 15-50 FPM --Belt size 52" X 75" --Weight 6500 lbs --AMPS (220 V / 460V ) 148/74.
Equipment Location:SOUTH
Joe Retzlaff
800-374-5009 ext:348
EXTREMA XS-3B37 Wide Belt Sander (3) Heads --3-Head, 36" width cap. Drum, Drum, Platen --Head Configuration: --1st Head: 8" Dia. rubber covered contact roll, 25 HP motor --2nd Head: 8" Dia. rubber covered contact roll, 25 HP motor; --3rd Head: Combination head with 4-7/8" dia. contact roll and 2-1/2" wide finishing platen, 20 HP motor. --Specifications: -- Height adjustment of both contact rolls with dial indicators -- 37" x 75" abrasive belts, OMRON solid-state abrasive belt tracking. -- 3 HP Variable feed drive of 15 - 50 FPM, -- GOODYEAR "endless belt" conveyor with automatic tracking, -- 0" - 6" max. motorized thickness opening with digital PLC control, keypad entry for thickness with LED readout, 0.5 HP motor, (4) 1" dia. screw jacks. --Equipped with & Features -- Infeed over thickness bar, infeed & outfeed spring loaded rubber covered holddown rolls on all heads. --Emergency stops at infeed & outfeed, air operated disc brakes on sanding heads, --Automatic opening of conveyor bed upon any emergency stop or shutdown.
Equipment Location:MIDWEST
Joe Retzlaff
800-374-5009 ext:348
EXTREMA PERFORMA XS-3B-37 Wide Belt Sander (3) Heads -- 37" Width cap. Drum, Drum Roller and platen --Head Configuration --1st Head: Contact drum 25 HP motor --2nd Head: Contact drum 25 HP motor --3rd Head:Roller and Platen combination head 20 HP --Features: --75” Belt Length --Available with 1 to 3 heads --Over thickness safety device --Infeed bed rollers --Digital thickness controller --Individual amp meters --Disc brakes on sanding heads --Telemecanique electrics --Camozzi pneumatics --Variable speed drive system --Mono-block construction to increase durability. --Specification: --Max. width cap 37" --Feed motor 3 HP --Elevation motor 0.5 HP --Max. thickness 6" --Min. thickness 1/8" --Contact drum 1st and 2nd head 8" dia. --Roller drum on 2nd head 5" dia. --CFM requirements 5400 --Feed speeds 15-50 FPM --Belt size 37" X 75" --Weight 6850 lbs --AMPS (220 V / 460V ) 184/92
Equipment Location:SOUTH
Joe Retzlaff
800-374-5009 ext:348
EXTREMA PERFORMAXS-3B-43 Wide Belt Sander (3) Heads --43" Wide Belt Sander Drum, Drum, Combination head --Head Configuration --1st Head: Contact drum 30 HP motor --2nd Head: Contact drum 30 HP motor --3rd Head:Roller and Platen combination head 25 HP --Features: --75” Belt Length --Available with 1 to 3 heads --Over thickness safety device --Infeed bed rollers --Digital thickness controller --Individual amp meters --Disc brakes on sanding heads --Telemecanique electrics --Camozzi pneumatics --Variable speed drive system --Mono-block construction to increase durability. --Specification: --Max. width cap 43" --Feed motor 3 HP --Elevation motor 0.5 HP --Max. thickness 6" --Min. thickness 1/8" --Contact drum 1st and 2nd head 8" dia. --Roller drum on 2nd head 5" dia. --CFM requirements 6300 --Feed speeds 15-50 FPM --Belt size 43" X 75" --Weight 7500 lbs --AMPS (220 V / 460V ) 220/110.
Equipment Location:SOUTH
Joe Retzlaff
800-374-5009 ext:348
EXTREMA PERFORMA XS-3B-52 Wide Belt Sander (3) Heads --52" Wide Belt Sander Drum, Drum, Combination Head --Head Configuration --1st Head: Contact drum 30 HP motor --2nd Head: Contact drum 30 HP motor --3rd Head:Roller and Platen combination head 30 HP --Features: --75” Belt Length --Available with 1 to 3 heads --Over thickness safety device --Infeed bed rollers --Digital thickness controller --Individual amp meters --Disc brakes on sanding heads --Telemecanique electrics --Camozzi pneumatics --Variable speed drive system --Mono-block construction to increase durability. --Specification: --Max. width cap 52" --Feed motor 3 HP --Elevation motor 5 HP --Max. thickness 6" --Min. thickness 1/8" --Contact drum 1st and 2nd head 8" dia. --Roller drum on 2nd head 5" dia. --CFM requirements 6500 --Feed speeds 15-50 FPM --Belt size 52" X 75" --Weight 8100 lbs --AMPS (220 V / 460V ) 233/117.
Equipment Location:SOUTH
Joe Retzlaff
800-374-5009 ext:348
Mono-block construction to increase durability. -- Combination sanding head with rubber covered contact roll & graphite covered platen. -- Over thickness safety device. -- Digital thickness controller with LED readout accurate to a thousandths of an inch. -- "Automatic Thickness Setting" device for easy setup. -- OMRON Electronic belt tracking. -- GOODYEAR Endless conveyor belt with automatic belt tracking. -- REGAL Variable feed speed drive unit. -- Large cabinet style doors for easy access to all parts. -- Pnuematic belt tensioning. -- Double infeed & outfeed covered holddown rolls. -- Infeed conveyor extension with safety stop bar, emergency stop button and motor load meter. -- Operations manual & free box of 3M Sanding Belts. -- Optional 460 volt / 3 phase.
Equipment Location:SOUTH
Joe Retzlaff
800-374-5009 ext:348