• Used
  • New
 
  •  
 
  •  
 
  •  
 

 
5 Results Found for Jointer and Finger Jointer Viewing 1 - 5 of 5 results

Circular-Saws

Band-Saw-Blades-Wide

Wear-Parts

Tools

Chipper-Parts

Wear-Parts

Chainsaw

Mechanical-Harvesters

Marking-and-Tally
Find More Supplies
STANDARD LISTINGS
INDUSTRIAL model "3470" with right & left shaper section. - Cap.: 5/8" - 2" max. thickness, 2" - 12" max. width, 5" min. (depending on joint length) - 60" max. material length. -- Equipped with: (2) 3 HP precision trim saws, (2) 10 HP shaper motors, 10-1/2" dia. max. cutting circle; late model Bonfield single chain with 5" block capabilities. -- Rebuild of the shaper includes: Complete rewiring and motors rebuilt, machine stripped to bare frame, cleaned, checked, and painted . Includes motor control center. -- Shaper system includes: Air bag pressure head with quick change feature & brush holddowns.
Equipment Location:NORTHWEST
EX-FACTORY INC.
704-841-2001
Model "3496" Finger Joint Shaper: 5/8" - 2" Thickness cap. x 2" - 8" width (with lugs on 9" centers) x 7-1/2" - 30" length. -- Right- & left-hand shapers with cross-transfer section, (2) 3 HP trim motors, (2) 10 HP shaper spindles, tappered spindles, 9" dia. cutting circle. - 1999 rebuild included a new Bonfield BL-62003 cast-iron feed chain with frequency variable chain drive for lug speeds from 60 to 90 LPM. Machine has good drive sprockets, tail drum; good bed rails with inserts, recent air bag pressure head with "quick change" feature, and brush holddowns. Shaper section feed works set at 92 lugs per minute. -- Equipped with: APQUIP Glue applicator with doctor block and transfer to assembly section. -- Model "3550" Hydraulic Assembly Press. - 16' max. cutoff cap., automatic cycling, feed speed varies from 50 to 200 FPM. Powered infeed flat top chain with side alignment rolls to the retard section. -- Pieces advance through the cutoff saw to a moveable limit switch and are cut-to-length, bottom mounted 5 HP flying cutoff saw for continuous non-stop assembly, the cut-to-length piece drops down into a final squeeze chamber while the next piece is cut-to-length, finished lengths are pushed out by the next piece onto material outfeed arms. -- Machine reconditioned by Bonfield Infdustrial Services in September 1999 and operated until May 2006.
Equipment Location:PACIFIC NORTHWEST
EX-FACTORY INC.
704-841-2001
Model "3470" with: Right & left shaper sections. - Cap.: 5/8" - 2" Max. thickness, 2" - 8" max. width (with lugs on 12" centers, cureently arranged for 6" max. width with lugs on 9" centers), 8" min. - 96" max. length. NOTE: MJachine has been modified for 60" max. length, can be converted back to the original 96" infeed lengths. -- Equipped with: (2) 3 HP score saws, (2) 5 HP trim saws, (2) 20 HP shaper motors. -- Variable feed lug chain drive with: variable speed control, air bag pressure head with "quick change" feature and side conveyors; APQUIP extrusion type glue applicator with block counter & 1.5-gal pot; manual transfer to the Assembly Press. -- Model "3550" Assembly Press: 30' Max. cutoff/press cap., automatic cycling, feed speed varies automatically depending on part & cutoff lengths from 50 - 200 FPM; powered infeed flat top chain 6" wide x 15' long with side alignment rolls to the retard section. -- Pieces advance through the cutoff saw to a moveable limit switch & are cut-to-length; bottom mounted 5 HP flying cutoff saw for continuous non-stop assembly. -- The cut-to-length piece drops down into a final 30' squeeze chamber while the next piece is cut-to-length; finished lengths are pushed out by the next piece onto material outfeed arms. -- Complete with: (4) Re-trim saw for shorter length cut while Press is used for full length capacity and one complete set of tooling. -- NOTE: Price includes a used 1995 Western model 875 automatic cutterhead grinder for sharpening fingerjoint heads, mill to pattern, "L" shaped and face type grinding. Cutter cap. face grinding up to 12" long x 14-5/8" dia; bevel grind up to 6" long x 14-5/8" diameter. Grinding motor 1.5 HP with grinding speed between 1,725 and 3,450 RPM. The grinding wheel automatically infeeds the amount that the operator designates in the program. Panelview operators station control with AB "504" processor. Lineal bearing carriage for 14" automatic table traverse. Variable wheel speed in both directions. (Priced on our website as [GS-011279] for $17,850.)
Equipment Location:NORTHWEST
EX-FACTORY INC.
704-841-2001
INDUSTRIAL IWS 10 Finger Jointer:Shaper unit will handle material 2" to 8" wide, 5/8" to 2" thick and 5" minimum length.Equipped with: -- ( 2) Trim saws with 5 HP motors, (2) Scoring saws with 3 HP motors and (2) Shaper spindles with 15 HP motors - 1-13/16" dia.. -- Feed speeds from 0 to 150 FPM. Average speed of (100) lugs per minute; feed chain is equipped with lugs on 9" spacing. -- New design "APQUIP" dual glue applicator with improved glue spreading and simplified pump. -- Model 3502 90° brush transfer to the assembly and Flying Cut Off Saw. -- MOD "3550 HAL" - Assembly Press, 16' long, with (1) retrim saw, air over hydraulic clamp & squeezing including Flying Cut Off Saw with 7.5 HP saw motor.Complete with: (3) Infeed block bins with "waterfall" belt conveyors to bring organized blocks to the infeed operator and on to the brush feeder.
Equipment Location:EASTERN CDN
EX-FACTORY INC.
704-841-2001
INDUSTRIAL Model "FJS-25" RIGHT & LEFT SAHPER SECTION with INDUSTRIAL 3550 ASSEMBLY SECTION -- "FJS" Shaper Capacity: 5/8" - 2" Max. thickness, 2" - 8" max. width (with lugs on 12" centers), 5" min. - 60" max. length (60" at reduced feed rate). -- Equipped with: (2) 5 HP Trim saws, (2) 15 HP shaper motors with 9" extreme swing, APQUIP glue applicator, Ziegelmeyer feed chain with lugs on 7-1/2" centers (installed in 1991); capable of chain speeds to 60 FPM max. -- INDUSTRIAL Model "3550" Press Section. - Capacity: 20' Max. cutoff, automatic cycling, powered flat-top chain infeed conveyor with powered side alignment rolls to pre-squeeze & align the joint, (2) main feed wheels with a holddown shoe add pressure, 3 HP feed drive - press speed from 50 - 200 FPM. Pieces advance thru the cutoff saw to a moveable limit switch & are cut to length; 5 HP flying cutoff saw. The cut-to-length piece drops down into a final squeeze chamber while the next piece advances and is cut to length; finial lengths are pushed out by the next piece onto material outfeed arms. -- Includes motor control center for all operations, 1 pair (6 ea.) 8-bolt, 9" swing hydro-heads, an 8-bolt set-up stand and a misc. assortment of spare parts. -- NOTE: Includes (1) extra section of Press
Equipment Location:MIDWEST
EX-FACTORY INC.
704-841-2001