• Used
  • New
 
  •  
 
  •  
 
  •  
 

 
84 Results Found for Band Resaw Viewing 1 - 20 of 84 results
STANDARD LISTINGS
Ashmore Horiz. Grade Resaw w/TurnAround; 18” x 18” Cap.; Cab; Infeedw/Cant Positioner; Outfeed w/Separator& Transfer; Hyd. Pack; Mtr & Controls
Equipment Location:South Bend, IN
Tri-State Auction & Realty, LLC
865-376-7009
Baker Single Head Band Resaw with Belt Return
Equipment Location:Clarksburg, TN
LPS Equipment & Acquisition Co.
731-986-4351
BAKER A Bandsaw Horizontal Resaw -- Single Head Re-Saw, 15 HP TEFC motor, 6" wide x 12" high material capacity or 8" wide x 4" high above the blade with conveyor set a 0°. -- Equipped with: Spring infeed holddown, variable speed controlled by a hydraulic flow control valve and 2HP pump, non-tilting conveyor, and 28" steel bandwheels, BAKER'S exclusive low profile flat plate guide system w/rear rollers. Blade dimension 1-1/4". Note: New belt, wheels crowned.
Equipment Location:MIDWEST
EX-FACTORY INC.
704-841-2001
Machine Number: 1643 Machine Type: Resaw Manufacturer: Baker Model #: Model A Location: Mid West Baker Model A Resaw Reconditioned Variable Speed Feed Serial# 94-969
Equipment Location:Mid West
Carolina Used Machinery
828-773-2204
Baker Model AX Band Resaw 2000 Under 1000 hours Gas Powered, 24 HP Onan engine Hydraulic belt in-feed and return Hydraulic powered hold down and hold over Capacity 8" x 12" cant, any length with supports Produces smooth and accurate cuts From 1/4" to 6" thick to 12" wide REDUCED!
Equipment Location:Blowing Rock, NC
Carolina Used Machinery
828-773-2204
BAKER BANG SAW WITH 2 40HP MOTORS, MAKES 4 CUTS AT ONCE
Equipment Location:Yuma, TN
LPS Equipment & Acquisition Co.
731-986-4351
BAKER C 4-HEAD Horizontal Resaw with Return;6" Wide x 12" high capacity Re-Saw. -- Standard spring blade tensioning system; 13'-2" x 1-1/4" x 0.035 Blade provides thin Kerf savings. -- Quick & easy blade height adjustments. -- 28" Diameter, CNC machined, dynamically balanced, all steel band wheels, (4) bolt flange. -- Rough top feed belt combines with opposing side feed rolls and top hold downs. -- 20 HP High Efficiency, 3-Phase electric motor on each head. -- Variable feed speed from 20 to 120 FPM (6 to 36 MPM). -- Includes: Return conveyor for resaw of wide width.
Equipment Location:MIDWEST
EX-FACTORY INC.
704-841-2001

Baker Band Resaw

$175,000
SHOW DEMO - IN STOCK AND READY TO GO!! BAKER 20' BP DOMINATOR BAND SAWMILL WITH HYDRAULIC CONTROLS MOUNTED ON A CONTROL STAND, 50HP TEFC MOTOR, COMPUTER SET WORKS, ELECTRICAL PANEL COMPLETE WITH STARTERS, MOTOR OVERLOAD PROTECTION, NEMA 12 ENCLOSURES. PREIRED 15HP HYDRAULIC POWER UNIT, 1 1/2" BAND WIDTH, THREE FENCE ARMS, THREE TOE ROLLERS, INLINE DEBARKER. TWO LOG CLAMPS. ONE (1)CHAIN STYLE LOG TURNER, PRECISION BALL SCREW HEAD RAISE AND LOWER, DUAL CHAIN CARRIAGE DRIVE, BOARD DRAG BACK RETURN, BUILT IN MATERIAL REMOVAL CONVEYOR, VARIABLE FEED CONTROL, 36" DIAMETER PRECISION MACHINED BAND WHEELS, BLADE LUBRICATION DRIP TANK, HYDRAULIC BLADE TENSIONING, LASER LIGHT. INCLUDED CONTROL CAB WITH HEAT AND AIR CONDITIONING BAKER 3 STRAND LOG IN FEED DECK WITH PAC MAN LOADER ARMS BAKER STATIONARY BOARD EDGER WITH 15HP MOTOR WITH TAILING BELT BAKER REVERSE EDGER SYSTEM - POWERED ROLLER WITH FLIPPER AND KICKER, ACCUMULATION CONVEYOR, TIP TABLE AND RETURN CONVEYOR BELT. 2 EACH - SLAB RACK 2 EACH - LUMBER RACK
Equipment Location:Ellington, MO
Baker Products
573-663-7711
REDUCED Machine Number: 1182 Machine Type: Resaw Manufacturer: Brewco Model #: 3-Head Location: South East Brewco Big Band Saw 3 head machine 480Volt 3 Phase Mgf 1996 28" wheels Band length 13'2", width 1 1/4" Hydraulic drive feed 3 phase 5 HP motor Head motors 20 HP 6" maximum cant width Cuts 4-6" hardwood 70 fpm Airbaglift with easy spacer height adjustment Comes with spacers and some spare blades Good condition and ready to run
Equipment Location:Blowing Rock, NC
Carolina Used Machinery
828-773-2204
Brewco B-800 4 Head Band Resaw, Wheels have been recrowned and new bearings, Linear bearings & Rails on adjustable air guides have been replaced. Runs a 2" Band. Any air regulator, gauge, or micro-valve that needed was replaced. It has a 4' x 8' in feed belt with the horizontal chains in feed. A 4' x 16' out feed belt, and a 6" x 32' return belt. It has a hydraulic unit with 2 motors and 2 pumps.
Equipment Location:Clarksburg, TN
LPS Equipment & Acquisition Co.
731-986-4351
5-head re-saw line with kick-off return after 1st. saw, includes hyd. system and electric disconnect combination starter panel. Also included is a disconnect at each saw. Also included is the dust pick-up ducting for the 5 head line.
Equipment Location:Clarksburg, TN
LPS Equipment & Acquisition Co.
731-986-4351
Machine Number: 629 Machine Type: Resaw Manufacturer: Brewco Model #: Big Band Location: South East Brewco 4 Head Resaw Four Head Big Band
Equipment Location:Blowing Rock, NC
Carolina Used Machinery
828-773-2204
BREWCO MDL BSBH SUPER BAND 4 HEAD BAND RESAW W/20HP ON EACH HEAD; S/N SB4B414 Return available with it.
Equipment Location:Clarksburg, TN
LPS Equipment & Acquisition Co.
731-986-4351
BREWCO MDL BSBH SUPER BAND 2 HEAD BAND RESAW W/20HP ON EACH HEAD S/N SB25414-2
Equipment Location:Clarksburg, TN
LPS Equipment & Acquisition Co.
731-986-4351
Brewco B-1600 3 Head Band Resaw up to 16"x 16" Squares.
Equipment Location:Clarksburg, TN
LPS Equipment & Acquisition Co.
731-986-4351
Machine Number: 879 Machine Type: Resaw-Grade Manufacturer: Brewco Model #: B1600 Year: 2007 Location: South East Brewco B1600 Grade Resaw System Standard Run Around Plus Also Available Pop up Rollers Green Chain To Resaw POp Up Roller To Infeed Outfeed Chains Infeed Outfeed Chains incline FRom Runaround To Edger Custom Operator Cab Extra Hyd Unit For Additional Rolls And Chains
Equipment Location:Blowing Rock, NC
Carolina Used Machinery
828-773-2204
Machine Number: 1503 Machine Type: Resaw-Grade Manufacturer: Brewco Model #: B1600 Location: South East Brewco B1600 Grade Resaw Operator Cab Run Around System 5 Way Seperator infeed/outfeed deck Roll Cases Hyd Power Pack All Starters 16"x16"x16' Capacity 3/4" to 9" Thickness 2" Band
Equipment Location:Blowing Rock, NC
Carolina Used Machinery
828-773-2204
BREWCO MDL BBBH 2 HEAD BAND RESAW; (2) 20HP MTRS; S/N BB2J7236 (NO HYDRAULIC POWER UNIT; NO BELT)
Equipment Location:Clarksburg, TN
LPS Equipment & Acquisition Co.
731-986-4351
BREWCO BBBH -- 4-Head Horizontal Resaw;Working dimensions: 6" Wide x 8" high capacity and length 21" to 72"Band: Standard spring blade tensioning system; 13'-2" x 1-1/4" x 0.035 Blade provides thin kerf savings. Quick & easy blade height adjustments.Wheel dia.: 28" Diameter, CNC machined, dynamically balanced, all steel.Belting: Rough top feed belt combines with opposing side feed rolls.Saw motors: 20 HP High Efficiency, 3-Phase electric motor on each head.Variable feed speed 5HP hydraulic drive from 20 to 120 FPM (6 to 36 MPM).
Equipment Location:MIDWEST
EX-FACTORY INC.
704-841-2001
Brewer Single Head Band Resaw Model GE 2000 1B Serial# 060498
Equipment Location:Clarksburg, TN
LPS Equipment & Acquisition Co.
731-986-4351