• Used
  • New
 
  •  
 
  •  
 
  •  
 

 
38 Results Found for Veneer Equipment Viewing 1 - 20 of 38 results
RECENTLY ADDED
STANDARD LISTINGS
ADOLF JOHN & COMPANY Model "FS IV" Automatic Guillotine with 126" Max. length cap., 3-7/8" cutting height. -- 0.5 HP motorized parallel fence, adjustable from 1" - 64", push button controlled travel with digital readout, micro-adjustment by hand wheel. -- 7" Wide hydraulic pressure beam with rack & pinion travel; 5.5 HP gear pump motor for pressure beam and knife cutting operation, approx. (2) Sec cycle time/cut; -- Complete with: (2) Palm buttons for safety. -- All Hydraulics were reconditioned in 2013, and used very little since.
Equipment Location:PACIFIC NORTHWEST, AL
EX-FACTORY INC.
704-841-2001
Steam Heated Veneer Press Dryer. 4.2 meter (165") wide screen-type press dryer. New in 1990. -- (5) Five Sections, approx. 70 feet long. -- Rated for 6 bar/150 psi steam. -- Automatic modulation of steam supply valves and exhaust vents. -- Needs a new Stainless Steel Screen. -- Need to confirm but this machine should be easily utilized as 400V/50 Hz or 480V/60 Hz.
Equipment Location:SOUTHEAST
Bill Christoffersen
800-374-5009 ext:365
88" Cap., straight knife cut for end-grain clipping, double rod mechanical clutch dual-arm cam driven by 5 HP motor, foot pedal actuation of cycle. -- Max. (90) cycles/Min, motor mounted inside frame and V-belted to flywheel.
Equipment Location:MIDWEST
Tony Cornacchione
800-374-5009 ext:432
CAPITAL Half-Round Slicer with a 125 inch length capacity and the following additional features: -- 50 HP Drive. -- Removed from service and Checked. -- Includes loading onto Buyer's truck.
Equipment Location:MIDWEST
Bill Christoffersen
800-374-5009 ext:365
150" Width cap., double-rod mechanical clutch driven with approx. 8 HP motor, twin-palm button actuation of cycle, max. (90) cycles/Min; shear cut angle with angle mounted knife. -- Motor mounted inside frame with gear drive power to flywheel, infeed table with support brackets and outfeed frame support only. -- (1) Knife included.
Equipment Location:MIDWEST
Tony Cornacchione
800-374-5009 ext:432
CAPITAL Half-Round Slicer with a 150 inch length capacity and the following additional features: -- 50 HP Drive. -- Includes CAPITAL Knife Grinder at no additional charge. -- Fully Reconditioned to "like new"! -- This machine was reconditioned at the factory yielding a slicer value of around $300,000. Somebody went out of business and you get a real bargain price!
Equipment Location:MIDWEST
Bill Christoffersen
800-374-5009 ext:365
CARGATE D-860 Rotary Veneer Lathe, Heavy Duty: -- Built specifically to handle large diameter logs as well as small logs. It has a log length capacity of an easy 8'-6" and a diameter capacity of up to 5', peeling down to perfect 4" cores for optimal log utilization. -- This moneymaker looks like a big brother to a Premier Lathe. It comes complete with beefy Bull Gears and boasts plenty of output capacity along with the following main features and components:Specifications: -- BRUNETTE MACHINE WORKS Hydraulic Retractable Spindles - 4" inner, 8" and 11" outer. These are the same spindles as are utilized on a Premier Lathe. -- The spindles are driven by angle-cut 72" diameter Oil-Bath Bull Gears. (This is actually identical to an upgrade to Premier lathes still running.) -- Factory Hydraulic Backup Roll. (This backup roll rides on adjustable rollers riding down on top of the carriage. This prevents backup roll from pushing excessively hard against the core. It produces perfect 4" cores).Equipped with: -- DURAND Charger and Pumps (self centering). -- Factory Log Deck - Complete with S-drive and Gearbox. -- Factory Air Trash Gate, Infeed Conveyor (infeed to chipper). Infeed to PRENTICE Air Bag Clipper, Timing Wheel and Holddowns. -- Factory 5' Wheel, 6-knife, Veneer Chipper with Hold-down Drum Roller, and S-drive complete. -- 6' FERANO Chip Screen and Conveyor. -- 10' COE Knife Grinder. -- Steel Framework and 450 FPM plus uniwind speed!Highlights & Background: -- This lathe is capable of peeling very high production. In 1967 it was actually regularly peeling 225,000 sq. ft. 3/8 basis, or 400 - 500 cubic meters per 8-hour shift. The lathe is in wonderful overall condition and portions can be turned on today although it has not seen service since 2005. When you think "CARGATE" think "big PREMIER" and you will have the right idea.Price shown is in US Dollars. - Experienced Owner is flexible to assist in removal and perhaps installation.
Equipment Location:WESTERN CDN
Bill Christoffersen
800-374-5009 ext:365
126" (3,200 mm) Cutting length, 3.94" (100 mm) cutting height, motorized back fence from 1" - 31-1/2" cap. fence travels on hardened ways, 0.5 HP motor, LED readout for fence positioning & fine adjustment by front mounted hand wheel. -- Equipped with: Hydraulic pressure beam-and-knife powered by 10 HP hydraulic pump motor, 6" wide pressure beam with cutting force adjustment for beam-and-knife, beam assembly with self-lubricated slide ways. -- Complete with: Cutting line with 4-side plastic cutter counter gib, cutting edge light for material positioning, 2-hand push button operation for safety; features operation selection for manual & automatic working cycles.
Equipment Location:EASTERN CDN
Tony Cornacchione
800-374-5009 ext:432

Coe 249D Veneer Equipment

Call for Price
COE 249D Veneer Lathe with the following: -- LYNDEN Step feeder. -- Small log offset x-y spindle chucks. -- 27" maximum log diameter, 110" knife length. -- 1484 Veneer Lathe Big Bar. -- 1390 Veneer Lathe Core drive. -- 3 to 1 inner drive ratio. -- Capable of peeling 35 cubic meters per hour. -- This COE Veneer lathe line was completely rebuilt and installed in 2006. The lathe was operated less than one year and is reportedly in excellent condition.
Equipment Location:SOUTHWEST
Bill Christoffersen
800-374-5009 ext:365
Veneer grading and sorting line for 204" (5.2 meter) veneers. -- Working stations: Infeed chain; scissor lift; 50' long inspection table. -- 170' long sorting belt; gravity roller conveyor is staging area, (2) cross transfer carts.
Equipment Location:EASTERN CDN
Tony Cornacchione
800-374-5009 ext:432
Tapeless Veneer Splicer; 1.5 HP TEFC variable speed feed motor, 15 - 85 FPM feed speed; handles stock from 1/64" thick and 6" min. length up to 42" wide. -- Equipped with: 4-Roll infeed matching roll assembly, thermostatic controls for upper-and-lower heater bars (200° - 500° F temperature range). -- Complete with: Automatic oil mist lubrication; outfeed with powered take away roll for veneer, start/stop push buttons for feed motor, and overload & under voltage protection. -- This machine has been fully rebuilt and comes with a full one (1) year warranty on all parts.
Equipment Location:MIDWEST
Tony Cornacchione
800-374-5009 ext:432
DIEHL "VS 81" TAPELESS VENEER SPLICER with 1.5 HP Variable speed feed motor, 15 - 85 FPM, 42" throat. Handles stock from 1/64" thick & 6" min. length up to 42" wide, 14 - 75 stitches/Min., 100" x 75" table, manual raise and lower temperature controls (200 - 500ø) for heater bars. -- This machine was overhauled in 2012, and is ready for your production needs.
Equipment Location:PACIFIC NORTHWEST
Tony Cornacchione
800-374-5009 ext:432
Cross feed veneer splicer 3400 mm capacity, without the stacker -- 9.3 HP -- Veneer thickeness 0.6-3.0 mm -- Min. veneer width 80 mm -- Infeed speed adjustable from 0 to 45 m/min -- Outfeed speed adjustable from 0 to 60 m/min -- Slow speed adjustable from 0 to 15 m/min -- Width of heating plates 133" -- Total heated length 3.4 m -- Press beam stroke 20-120mm -- Working temperature adjustable from 100 to 200 deg C --Splicing pressure 5-16 bar -- Installed heating power 18 kW, heat up time 12 min. -- Total installed power 23 kW, power demand 13.8 kW -- Built-in hydraulic unit with air cooler to keep temp. from rising above recommended limits -- Built-in clipper with hydraulic command -- Knife cutting against rotating roll, -- Stainless steel heaters independently feed by electronic controller, auto sheet alignment -- Net weight 5500 kg
Equipment Location:MIDWEST
Tony Cornacchione
800-374-5009 ext:432
FEZER Model 3SE 3,6 1P+2R, 5-Section Veneer Press Dryer complete with the following features: -- 141-3/4" Max. drying width x 33' long drying tunnel plus 80" long cooling section, single deck top & bottom screen type feed, top screen heavier for pressing effect on the veneer (304-stainless steel B-18-12-12-14), bottom screen 304-stainless steel (B-12-12-12-14). -- Heat is generated by (5) gas fired thermal oil boilers. The thermal oil heaters provide heat to 5-sections (800,000 BTU/Hr. each); thermal oil temperature 320° F. The heaters can be fired with natural or LP gas. -- 60 HP fans with temperature control. Cap. per hour on 1/24" Sycamore is 6,000 sq. ft./Hr from 80% - 7% moisture content. -- Overall size: 54' Long x 20' wide x 14' high. -- Dismantling, rigging and loading included at no charge. -- Please click on the "View Literature" button found below the photos on this listing for more detailed factory information. -- NOTE: Slicing equipment is also available at this site. See Listing VL-010203.
Equipment Location:EASTERN CDN
Bill Christoffersen
800-374-5009 ext:365
FEZER 5PS3 P2R Veneer Screen Dryer; Ideal screen dryer for the thinnest and highest quality veneers!Consists of the following main components: -- (5) Heating Sections (steam heated) plus (1) Cooling Section. -- 10 Feet wide opening for veneer input. -- SIEMENS VFDs (multilple) and ALLEN-BRADLEY PLCs (multiple). -- Approx. 8 feet high; Overall 16 - 17 feet wide with guards etc., (66) feet long with cooling section.Remove as many sections as you want (roughly 8 feet per section) to reduce the length if desired.Used for about (2) years. New in 2005, never ran the full (40) hours per week.Already removed from service ready to load - a real savings!
Equipment Location:ATLANTIC CDN
Bill Christoffersen
800-374-5009 ext:365
FEZER Model FM-30, Veneer Slicer System complete with the following features: -- 12" Max. lumber slicing width with an up to 10" high cant, veneer thickness 1/85" to 3/8" and with +/- accuracy of 0.002"; fixed knife with a 75ø fixed knife bias angle. -- Upper feed beam with continuous belt feed for 164 FPM or 246 FPM, 26 HP feed motor, 6 HP head elevator motor for "rapid" dual speed up & down travel; feed head can be raised to 16" opening for easy maintenance. -- Equipped with: Motorized upper feed beam which adjusts automatically during slicing at cant changes, fine hand wheel digital adjustment of front bed longitudinally or vertically, belt guide bearings for stable lumber feed, automatic indexing of pressure head, rollers in in- & outfeed table reduce friction; table height 36". -- Includes: Digital readout on table height; push & pull screws for nose bar adjustment and up to 6" opening between knife and nose bar for easy touch-up of knife. -- FEZER Merry-go-Round conveyor system (84" max. material length), allows continuous feed of several pieces of lumber to the slicer over powered rollers and driven cross-transfer chains, forward feed speed 250 FPM and sideways traversing feed at 130 FPM, handles (4 - 10) pieces of flitches/Min; at a slicer feed speed of 246 FPM, it can produce approx. (10) pieces of veneer/Min. -- Year 2001, REFORM Model 51 Knife Grinder with a 59" (1500 mm) knife length capacity. -- Please click on the "View Literature" button found below the photos on this listing for more detailed factory information. -- NOTE: A Veneer Dryer is also available at this site. See Listing VL-010202.
Equipment Location:EASTERN CDN
Bill Christoffersen
800-374-5009 ext:365
FISHER+RUCKLE Crossfeed Veneer Splicing Line consisting of the following major components and features: -- FISHER+RUCKLE Type FBM-28 Prefeeder. -- FISHER+RUCKLE Type FLM-28 Crossfeed veneer splicer, 31-1/2" to 109-1/2" (800 - 2,780 mm) max. veneer length, 1/40" - 1/16" (0.6 - 1.5 mm) thickness, 2-3/4" (70 mm) min. width, Moisture Content: 8 - 12%. -- Feed speed 8 - 28 FPM (1.8 - 8.5 MPM), approx. (40) strips per minute Finished Veneer sheet sizes - length in grain direction: 31.5" - 109.5" (800 - 2,780 mm). Width across grain: 23.6"-78.7" (600 - 2,200 mm). -- FISHER+RUCKLE Type FZM-28 Intermediary conveyor. -- FISHER+RUCKLE Type FSM-D59295 Clipper. -- FISHER+RUCKLE Type FAM-2822 stacking device, complete with accessories with taping option included. -- CAM INDUSTRIES, INC. Model 20HW Hot Water Boiler. -- Machine specifications: Electrical requirements: 10.5 kW, Air requiements: 5.4 CFM (150 NL/min.) @ 6 bar/min. Hot water hook-up: 1" (DN25). Capacity of circulation pump: 4 l/Sec. or 64 US gal./min. @ 1.5 bar. line pressure -- Energy Consumption: 20,000 - 60,000 kCal/Hr. Primary system: Steam or hot water @ 145° C or thermo oil @ 180° C. Hot water secondary system; 1) for urea splicing glue: splicing temperature approx. 130° C. 2) for PVAC glue: Splicing temperature approx. 85° C. -- Estimated Dimensions & Weight: Length 6,200 mm (20.3') + stack length; width 3,900 mm (12.8'); height 2,500 mm (5.2'); Net weight 10,000 kG (22,000 Lbs); Working height (standard) is 1,140 mm (44.9"). Boiler not included in dimensions and weights. -- Splicer will be available by the end of November.
Equipment Location:PACIFIC NORTHWEST
Tony Cornacchione
800-374-5009 ext:432
FISHER-RUCKLE GLUEMASTER Veneer Glue Application Machine --The glue application machine, Gluemaster, applies the glue to both sides of the veneer package, in one pass, independent of veneer length. --Pressure Rollers: During the glue application, the veneer packages are pressed uniformly by the pressure rollers. Thereby it is possible to glue even difficult veneers and avoid glue between the veneer strips --Glue application dosage: During the glue application, the veneer packages are pressed uniformly by the pressure rollers. Thereby it is possible to glue even difficult veneers and avoid glue between the veneer strips --Specifications: -- Min. Coating Gluing Boyu 400 mm --Max. Coating Gluing Boyu 4000 mm --Min. Eni coating 45 mm --Max. Eni coating 515 mm --Min. Veneer Bond Height 10 mm -- Max. Veneer Bond Height 40 mm -- Working Speed 30 m / min
Equipment Location:MIDWEST
Tony Cornacchione
800-374-5009 ext:432
FISHER RUCKLE OMNIMASTER Feed Through Veneer Splicer; Veneer glue application with longitudinal splicing in one pass, single glue applicator. -- Veneer strip length: 133" to 29-1/2" min., veneer strip width 1-15/16" minimum. -- During production the operator has all specifications within the field of vision. All adjustments can be made without interruptions. -- Glue application: Adjustable gluing unit ensures a perfect glue application. The quantity of the glue can be adjusted to the type of wood or to the speed. -- Feed Drive: Upper and lower high-grade steel chain trucks are driven directly with hydraulic motors; approx. 17 to 20 joints per Minute. -- Material Infeed: The infeed rollers accurately align the veneer to the glue application roller and then transports the glued veneer to the heating section. -- Through Feed: The photocell controlled infeed guarantees accurate alignment of the joint and ease of feeding the machine.
Equipment Location:EASTERN CDN
Tony Cornacchione
800-374-5009 ext:432
The cross-banding operation is done on both ends of the veneer sheet simultaneously. It reinforces longitudinally spliced veneers by means of a resistant glue thread which is applied at the ends across the grain. -- The special infeed system of the gluing heads pulls tightly together even fine end splits. This veneer edge protection avoids damage which often occurs during further handling. -- Stitches veneers from 0.4 - 2 mm thickness, working width 14" - 106" (360 - 2,700 mm), variable feed speed from 16 - 100 FPM; 3 kW feed motor, table size 21-1/2" x 37" on RH side. -- Glue is applied in zigzag fashion via heated guide; (1) gluing unit on each side, one is fixed and the other travels via rails for adjustable width opening. -- Joins decorative and constructional veneers.
Equipment Location:MIDWEST
Tony Cornacchione
800-374-5009 ext:432