1989 Industrial IWS-10 & 3550 HAL Jointer and Finger Jointer$49,500 CDN

Contact Information

 
  

EX-FACTORY INC.

1805 Sardis Road N
Charlotte, NC 28270
Map ItPrint It

  

704-841-2001

  

View Seller's Entire Inventory and Information

Contact Seller

  
 
 
 
 
   
 
By using this service, you accept the terms of LumbermenOnline.com Visitor Agreement.

Captcha
Click refresh if text is not readable.  
 
Enter the text exactly as it is shown above. 
 
  
< img u="thumb" src="../Handlers/ShowThumbnail.ashx?ID=46129&FILE=THMB_FJ-0106191.jpg" />
< img u="thumb" src="../Handlers/ShowThumbnail.ashx?ID=46129&FILE=THMB_FJ-0106192.jpg" />
< img u="thumb" src="../Handlers/ShowThumbnail.ashx?ID=46129&FILE=THMB_FJ-0106193.jpg" />
< img u="thumb" src="../Handlers/ShowThumbnail.ashx?ID=46129&FILE=THMB_FJ-0106194.jpg" />
< img u="thumb" src="../Handlers/ShowThumbnail.ashx?ID=46129&FILE=THMB_FJ-0106195.jpg" />
< img u="thumb" src="../Handlers/ShowThumbnail.ashx?ID=46129&FILE=THMB_FJ-0106196.jpg" />
< img u="thumb" src="../Handlers/ShowThumbnail.ashx?ID=46129&FILE=THMB_FJ-0106197.jpg" />
< img u="thumb" src="../Handlers/ShowThumbnail.ashx?ID=46129&FILE=THMB_FJ-0106198.jpg" />
< img u="thumb" src="../Handlers/ShowThumbnail.ashx?ID=46129&FILE=THMB_FJ-0106199.jpg" />
< img u="thumb" src="../Handlers/ShowThumbnail.ashx?ID=46129&FILE=THMB_FJ-01061910.jpg" />
< img u="thumb" src="../Handlers/ShowThumbnail.ashx?ID=46129&FILE=THMB_FJ-01061911.jpg" />
< img u="thumb" src="../Handlers/ShowThumbnail.ashx?ID=46129&FILE=THMB_FJ-01061912.jpg" />
< img u="thumb" src="../Handlers/ShowThumbnail.ashx?ID=46129&FILE=THMB_FJ-01061913.jpg" />


EQUIPMENT DETAILS


  • Year:1989
  • Make:Industrial
  • Model:IWS-10 & 3550 HAL
  • Location:EASTERN CDN,
  • Stock Number:FJ-010619

 

EQUIPMENT DESCRIPTION

 

INDUSTRIAL IWS 10 Finger Jointer:Shaper unit will handle material 2" to 8" wide, 5/8" to 2" thick and 5" minimum length.Equipped with: -- ( 2) Trim saws with 5 HP motors, (2) Scoring saws with 3 HP motors and (2) Shaper spindles with 15 HP motors - 1-13/16" dia.. -- Feed speeds from 0 to 150 FPM. Average speed of (100) lugs per minute; feed chain is equipped with lugs on 9" spacing. -- New design "APQUIP" dual glue applicator with improved glue spreading and simplified pump. -- Model 3502 90° brush transfer to the assembly and Flying Cut Off Saw. -- MOD "3550 HAL" - Assembly Press, 16' long, with (1) retrim saw, air over hydraulic clamp & squeezing including Flying Cut Off Saw with 7.5 HP saw motor.Complete with: (3) Infeed block bins with "waterfall" belt conveyors to bring organized blocks to the infeed operator and on to the brush feeder.

SELLER'S RELATED INVENTORY

Seller Information

 
  


EX-FACTORY INC.

1805 Sardis Road N
Charlotte, NC 28270Map It

  

704-841-2001

View Seller's Entire Inventory and Information