Sawmill Equipment For Sale

42" Salem LP

Recently Refurbished 22" Ring Debarker New Controls Optional 22" Metal Detector

42" Salem LP Carriage

Salem 6' Band Heading

Salem Insulated Cab, 4’x8’, NEW glass reconditioned.

6', top wheel is 1" thick, air strain, was used for a line-bar resaw, good working condition

Salsco 60 " Shaving Mill Diesel engine Stationary Mill Seller believes it is a 2009 or 2010. There is 10 knives ( 5 rows with 2 knives each)

Salsco 60" Electric Shaving Mill Includes:Chip sizer/breaker

SAMUEL TANK-660V-150PSI 660 Gallon Air Receiver660 Gallon Vertical Air Receiver Tank. • Diameter O.D./I.D.: 42 O.D. • MAWP: 150 PSI @ 400° F • MDMT: -20°F @ 150 PSI • Capacity: 660 Gallons • Pressure: 150Support & Attachments: • 8 Base Ring • Safety Valve & Pressure Gauge - 700/MCTK-SW10-150Recommended Option: Zero Loss Compressed Air Condensate Trap w/WindowPowers through Condensate buildup and Ideal for Compressor applications up to 100 HP (500 SCFM).Ideal for inline filters up to 5000 SCFM. • The WaterHog™ design avoids small passages common on competitor designs, ensuring clog-free operation. • Fully Automatic Operations. No timer or manual settings • No Electrical Connections. WaterHog™ is powered by compressed air, avoiding the need for electrical wiring and connections. • Energy Saving Operation. Zero compressed air loss when properly installed with balance line. • Check with your utility to see if it qualifies for energy efficiency incentives. • WaterHog™ pays for itself when replacing open condensate drain valves or timer traps. • Low Profile. • The 4.7" vertical operating height allows WaterHog™ to fit where other larger units can't. • Max Operating Pressure: 200 psig • Min/Max Control Pressure: 40/130 psig • Min/Max Temperature: 34/170 F • Inlet / Outlet Connections: 1/2 inchPrice ...$ 450.00 (2) Year Warranty Included

Samuel Rogers 66" Knife Grinder

KENT - Single Head, ResawSpecifications: -- 15 HP Motor. -- Blade size: 168"; x 1"; x 0.035"; 2TPI. -- 6" Wide feed belt. -- Operational working heights: 1/4" minimum cut to 8"; maximum. -- Feed speed: 20 - 150 Feet per minute.

Like new 36" vertical linebar resaw. COMPLETE WITH RUN AROUND SYSTEM. Saws 14"W x 16"H x 12'L cants (can be extended). Operator's cab w/ controls. Elec. sys. w/ starters, prewired mach. Pre-plumbed hyd. sys. 20HP hpu, sub-steel, ten saws incl. Mach. disassembled. Crane additional. $90,000. OBO

Sanborn 6' Left Hand Double Cut Band Head Rig on 17 Degree tilt

Sanborn 5' Band Head Rig Air Strain w/ 100HP Electric Motor

Sanborn Machinery RH 8 Saw Drop Saw Trimmer with Hydraulic Drive

1984 Sanborn Min Max Wide Band Sawmill with Live Deck. Detroit 271 engine with the largest injectors that are made for that engine. It starts and runs well. Includes: hydraulic drive 3 chain live deck that is about 16' long and 12' wide with a stop and loader and arms that go across the bed of the mill. The logs must be rolled across the arms to the 4 head blocks. The frame of the live deck is mounted on 3x3x3 concrete cubes. set of 4 large head blocks with the same design as the original but which are about 12" large capacity than the originals. 40 foot long 3 chain green chain with new hydraulic motor and large gear reduction unit, 3 saw Chase 24+" edger with a 271 power unit that starts and runs well. 7 bands here and another 5 being repaired. Maintenance and Repairs Done: - balanced both wheels, reground both wheels - removed some weight from the upper wheel - added a weight strain system instead of a small spring - added vibration damping connections - provided electric shut off and throttle to the engine - added an auxiliary open center hydraulic pump and valves. The pump is driven off the front of the crankshaft of the engine - replaced the bearings throughout the mill - strengthened the take away table to take very heavy loads - installed a new set work screw system - removed the pantograph for hydraulic supply and replaced it with an igus hose and cable carrying chain Call 800-459-2148 for more info.

2000 Sanborn Min Max This is not a whole mill. - Two complete good working Silvatech Set works , - Four Heavy Duty Head Blocks . Board Dogs, Cant Dogs, Turners and Tapers all Hydraulic. These were custom built super heavy duty for this mill . Very well cared for. Great care taken in the removal. - Every thing is under cover. - It’s the complete system with everything you need to put it back together, all labeled and photos. - The spare set works was near new when bought. - Everything is on heavy duty pallets can be shipped. Call 800-459-2148 for more info.

This mill has been damaged, but if you want good parts there are some here. Call 276-472-2199 for more info.

SANDMAN M74836 Downdraft Sanding TableGreat sanding table for a singular function such as doing cabinet doors, door fronts, etc. This downdraft table has a 6″ overhang on the front side making it good for sanding while sitting. Machine comes standard with casters, utility tray, & Felt-lined Platforms.Specifications: 48 L x 36" W top surface with heights of 32", 34" $ 36". -- Overhangs of 6" front. 0" back and 4" ends. -- (2) DP20252 Filters and (1) PF4029 pre-filter. -- 1 HP Baldor Motor – Standard Single Phase 110V (13 Amps) -- (18) Month warranty on parts.(Single and 3-Ph 220V available)NOT IN STOCK - CALL OR EMAIL FOR CURRENT LEAD TIME TO SHIP. PRICING SUBJECT TO CONFIRMATION.

SANDMAN DL7236 Downdraft Sanding Table;The SANDMAN Sanding Table is a dedicated sanding station that doubles as a workbench. -- 72" X 36" Rubberized work surface. -- 1.5 HP T.E.F.C. 220V 1-Phase motor with 10-5/8" LAU blower with sealed ball bearings. -- Industrial casters with 4" wheels, (2) ridged, (2) swivel-lock 2-ways. -- Hinged tilt-up top with gas strut lid support for easy filter servicing. -- Adjustable in height from 34" - 38". -- Grid system top adds versatility. -- 10.4 Cu. Ft. of built in storage area with 1 pull out shelf. -- 18 Months Limited WarrantyNOT IN STOCK - CALL OR EMAIL FOR CURRENT LEAD TIME TO SHIP. PRICING SUBJECT TO CONFIRMATION.