Woodworking Equipment For Sale

POWERMATIC KUFO 1632 (KUFO SK-15A) Wide-Belt SanderSpecifications: -- Open-sided single head 16" Wide Belt Sander. -- Open-sided design to allow up to 32" wide workpiece in (2) passes. -- Combination head with a 4" diameter rubberized contact drum. -- Head with a finishing platen. -- 5 HP Single-phase or 7.5 HP 3-phase motor. -- Air abrasive belt tracking. -- Manual readout to reference the 0" - 6" thickness setting. -- Center jack to set bed location. -- 0.25 HP Conveyor drive with 20 FPM. -- (2) Infeed & (2) outfeed spring loaded holddown rollers. -- Side extension support, load meter and safety shutoff. -- Operators manual.

10 HP. 4"x 10" cutting capacity. Upcut and top shield operated by air w/ foot peddle control. Top table size 25"x 27" Good working condition. Call 918 752 8142

Powermatic model 66 Table Saw

Powermatic model 1696 Jointer 16" capacity 96" table

Powermatic SLR12 Straight Line Rip Saw

POWERMATIC 221 PLANER WITH BYRD HELICAL HEAD20" x 8" Cap., 10 HP TEFC belted drive motor, BYRD Helical cutterhead, hand wheel micro-adjust table; 1 HP feed motor for variable speed from 20 - 50 FPM, segmented infeed roll and sectional chipbreaker, 4" dia. smooth outfeed roll. -- Complete with: Magnetic starter and dust hood.

Powermatic TS 80 Shaper Call 800-459-2148 for more info.

POWERMATIC - 28, ...Shaper1-1/4" Dia. spindle; 7-1/2 HP - 3,600 RPM motor; 3,300 - 9,500 RPM spindle speeds via Factory installed Variable Frequency Drive.4-3/4" Cap. under nut when using the 1-1/4" spindle; spindle brake; 30" x 39" table.

TABLE SAW TOP MEASURES 44" WIDE X 76 ½" LONG TABLE HEIGHT FROM FLOOR 34% " COMES WITH 5 - 12" DADO BLADES 1 HORSE POWER POWERMATIC MATERIAL FEEDER 5 HORSE POWER SAW ARBOR MOTOR 440 VOLT 3 PHASE

POWERMATIC - RB-37, ...Single Head Wide Belt Sander1-Head, 36" width cap., combination sanding head. -- Includes: 4" Dia. contact roll & 2" wide polishing platen, micro-adjust platen; 15 HP main motor. -- Abrasive belt size: 37" x 60"; with air tensioning, air jet abrasive belt tracking.1 HP Feed drive; variable feed speed of 15 - 30 FPM conveyor speed.0" - 5-1/4" Opening with: (4) Screw jacks; double infeed & outfeed rubber covered holddown rolls. -- Complete with: Magnetic starter; overload protection; load meter; emergency brake.

Producto Gothic Fence & Post Picket Machine. Out and Ready to ship. Producto is now Global Marketing Group.

PROFILEMATIC 503 PROFILE SANDER3-Head feed through, sands from top at adjustable angles narrow moulding type parts as well profiled edges on panels.Equipped with: -- (3) Top VPS vibrating air-loaded sanding units, 0.5 HP vibrating motor ea., sanding heads have (2) pneumatic cylinders for sanding pressure control and oscillate with 1/2" stroke on dust-protected round guides, variable vibration speed from 200 - 1,800 RPM; adjustment range of 120ø to conform to profile, equipped with air shower to clean workpiece & sandpaper automatically. -- Part transport is achieved by a 4-1/2" wide linatex coated conveyor belt system, "quick adjustment" holddown wheels & fence system, variable feed speed 0 - 35 FPM powered by a 0.25 HP DC gear drive (forward & reverse feed mode). -- Each sanding head with its own controls for manual raise & lower, pressure control and vibrating speed. Profile width approx. 1/2" min. to 4" max., material feed through thickness up to 5"; support fences for up to 10" moulding width.

Make an offer - Machine is in an Ex-Factory Liquidation. 4-Station Profile Shaper Specifications: 6" Chain drive with non-marking rubber top pads traveling on a hardened and ground precision dia. 5/8" round rods, Top pressure beam driven, Heavy duty fabricated transporter frame, Forward and reverse mode and block mode for creating sanding tools Precision X & Y axis mounting stands, 60° rotating tilt on mounting stands with positive lock, Independent activation control at each station, Adjustable infeed fence system, All dust hoods and guards, 2 HP AC variable speed gear drive 5 to 60' per min. Workstation 1: 3.5 HP TEFC Saw Arbor Motor, 1" Dia. Spindle, Dust Hoods with 4" outlet, Mounted on precision X & Y slides Workstation 2 & 3 - Belt Sanding Unit: 2 HP AC motor drive, Air belt tension system, Independent belt tracking system, Air activated sanding pad with touch control, 2" sanding belt width, Guards and Dust hoods with 4" outlet Workstation 4 - Wheel Sanding Unit: 3" HP variable speed (0-3,400 RPM) AC TEFC drive motor, 1" or 1.25" arbor 3.5" long, Dust Hood with 4" dia. outlet, Mounted on precision X & Y slides SPECIAL NOTE: Needs New PLC or wire for traditional controls NOTE: Above specs are taken from literature and thought to be accurate. As always please take advantage of the inspection period to verify. Items seen in the background are NOT a part of this Lot.

Progressive Systems Inc End Matcher

PROSAND HF-412 Curved Part Belt SanderBelt oscillates up and down.÷Feed wheel removable.

QUICK MACHINERY N-P80 Air Pod style Cold Press. -- Heavy Duty I-beam construction with machined steel plates for flat smooth pressing surface.Specifications: -- Platen pressing area size: 49" x 97" with end loading on 49" side. -- 80 PSI Platen pressure over the entire surface area with 102 PSI supply air pressure. Pressure is applied by 12.8" dia. air pods with 5.9" stroke; (28) air pods total for this size press. -- Air powered raise and lower idler rollers in the bed of the press for loading & unloading panels; raising & lowering of conveyor by control button on panel. -- Motorized Adjustable Daylight Opening from 2" to 40"; push button controls operate an electrically powered chain driven worm gear drive system for precise positioning of upper platen setting/opening. -- Controls: 60-Min cycle timers provide visual and audible signals at the end of each cycle and automatically releases platen air pressure at the end of each cycle if desired. -- Single platen 49" X 97" . -- The press model shown in pictures is a dual platen powered feed through end load press. -- Actual model is N-P80-04-08-EL-1PL-M-40-R-1Z

QUICK MACHINERY N-P80 Air Pod style Cold Press. -- Heavy Duty I-beam construction with machined steel plates for flat smooth pressing surface.Specifications: -- Platen pressing area size: 62" x 146" with end loading on 62" side. -- 80 PSI Platen pressure over the entire surface area with 105 PSI supply air pressure. Pressure is applied by (60) 12.8" dia. air pods with 5.9" stroke; -- Air powered raise and lower idler rollers in the bed of the press for loading & unloading panels; raising & lowering of conveyor by control button on panel. -- Motorized Adjustable Daylight Opening from 2" to 40"; push button controls operate an electrically powered chain driven worm gear drive system for precise positioning of upper platen setting/opening. -- Controls: 60-Min cycle timers provide visual and audible signals at the end of each cycle and automatically releases platen air pressure at the end of each cycle if desired. -- Single platen 62" X 146". (2) Air pressure zones for upper platen: (4' x 8' and 5' x 12') -- Optional powered roller tracks for an additional fee. -- The press model shown in pictures is a dual platen powered feed through end load press. -- Actual model is N-P80-05-12-EL-1PL-M-40-2Z

QUICK MACHINERY N-P50 Air Pod style Cold Press. -- Heavy Duty I-beam construction with machined steel plates for flat smooth pressing surface.Specifications: -- Platen pressing area size: 62" x 146" with side loading on 146" side (also available as end loading). -- 50 PSI Platen pressure over the entire surface area with 90 PSI supply air pressure. Pressure is applied by 12.8" dia. air pods with 5.9" stroke; (36) air pods total for this size press. -- (2) Pressure air pressure zones: 5' x 12' and 4' x 8'. -- Air powered raise and lower idler rollers in the bed of the press for loading & unloading panels; raising & lowering of idle conveyor roller tracks by control button on panel. -- Motorized Adjustable Daylight Opening from 2" to 40"; push button controls operate an electrically powered chain driven worm gear drive system for precise positioning of upper platen setting/opening. -- Controls: 60-Min cycle timers provide visual and audible signals at the end of each cycle and automatically releases platen air pressure at the end of each cycle if desired.

QUICK MACHINERY N-P50 Air Pod style Cold Press. -- Heavy Duty I-beam construction with machined steel plates for flat smooth pressing surface.Specifications: -- Platen pressing area size: 62" x 146" with side loading on 146" side. -- 50 PSI Platen pressure over the entire surface area with 93 PSI supply air pressure. Pressure is applied by 12.8" dia. air pods with 5.9" stroke; (36) air pods total for this size press. -- Air powered raise and lower idler rollers in the bed of the press for loading & unloading panels; raising & lowering of conveyor by control button on panel. -- Motorized Adjustable Daylight Opening from 2" to 40"; push button controls operate an electrically powered chain driven worm gear drive system for precise positioning of upper platen setting/opening. -- Controls: 60-Min cycle timers provide visual and audible signals at the end of each cycle and automatically releases platen air pressure at the end of each cycle if desired.Actual Model is a N-P50-05-12-SL-1PL-M-40-R-1Z.• Maximum platen pressure: 50 PSI at 93 PSI supply pressure• Lower platen dimensions: 5' x 12'• Side-loading design• Number of upper platens: 1• Upper platen dimensions: 5' x 12'• Vertical opening: Motorized adjustable from 2" to 40"• Lower platen roller tracks: Yes, non-powered roller tracks• Number of 12.8" diameter, 5.9" stroke air pods: 36• Number of air pressure zones: 1 (5' x 12' pressing)Optional powered roller tracks are available. -- The press model shown in pictures is a dual platen powered feed through end-load press.

QUICK L-HLPP-2-20-43-8-12 ...2-Sided Hydraulic Laminating Press: -- Number of working sections: (2) -- Working width, section #1: 6" and 8" -- Working width, section #2: 8", 10"; and 12" -- Maximum working length: 6,200mm (20.3') -- Maximum working height: 1,100mm (43.3") -- Pressure at the glue line: Up to 175 PSIMain Laminating Cylinders: -- Number of cylinders, section #1: (14) -- Number of cylinders, section #2: (21) -- Size of cylinders: 100 mm dia. x 80 mm strokeHolddown Cylinders: -- Number of cylinders, section #1: (14) -- Number of cylinders, section #2: (21) -- Size of cylinders: 40 mm dia. x 150 mm strokeLift Cylinders: -- Number of cylinders: (2) on each side = (4) -- Size of cylinders: 63 mm dia.Hydraulic Pump: -- Drive motor: 10 HP -- Maximum pressure: 140 kG/cm² -- Maximum Holddown Cylinder Pressure: 50 kG/cm² -- Maximum Side Lift Cylinder Pressure: 50 kG/cm² -- Shipped without hydraulic oil in the oil tank