Woodworking Equipment For Sale

Diehl Straight-Line Ripsaw parts -New and good used parts that fit theSL-52 and 750 model Ripsaw.Includes -One Remachined race, Two good chains, Two race followers, new pins.New Upper pressure head feed rolls -6 long rolls and 8 short rolls that go around the blade, and pressure springs.Have other miscellaneous parts - Oilers, Bearings, Doors, Motor, and more stuff...We used to rebuild Diehl ripsaws. This is the remaining inventory of parts.A new "Chain & Race" package from Diehl will be $5,000 or more - This is the heart of a ripsaw. If you are serious about keeping your Diehl ripsaw in good shape, this is a good buy.

DIEHL ESL-10 Straight Line Rip Saw, with LaserSpecifications: -- Table size 39-1/2" x 52" x 35" H. -- Throat 17-1/2". -- Distance from front of blade to table 21-1/2". -- Max. blade dia. 16". -- Max. thickness 1-1/2". -- Guaranteed glue joint length 48". -- Feed speed 30 FPM.Equipped with: -- 10 HP Blade motor with Automatic brake. -- Pyramid corrugated feed chain, with 1 HP Motor. -- (5) Pairs of 2-1/2"; Dia. x 1-1/2"; W Hold-down rolls. -- 20-1/2"; L x 2"; H Fence. -- Upper & Lower anti-kickback fingers. -- Manual feed chain lubrication.Complete with: -- Installation, Maintenance & Operating Instructions. -- Laser. -- 11-3/4" Dia. Blade. -- (4) Swivel Casters.

DIEHL 55 Straight Line Ripsaw:Specifications -- 15HP - 3,450 RPM Direct drive arbor motor, -- 2" dia. arbor, 18" blade cap., 4" max. depth of cut, -- 12" min. part length, -- 21-1/2" width of table to the right of blade & 30" to the left, 43" table length. -- 2 HP 4-Step feed drive 30 - 50 - 75 & 120 FPM; twin chain drive,Equipped with & Features -- Automatic dip lubrication. -- Top pressure system with (6) full width rollers & (2) split rollers over blade. -- All cast iron machine -- Runs very nice --Complete with: Rip fence,.

Diehl Model 75 Straight Line Rip Saw Chain is in good shape. Left and right chains are worn evenly. Includes: Laser Variable Speed: 4-speeds

DIEHL STRAIGHT LINE RIP

MLS Number 10682943 DIEHL SL52 STRAIGHT LINE RIP SAW Bottom arbor 4-1/4"X8-1/2" capacity 15 HP 3,545 RPM arbor drive motor Infeed speed up to 200 FPM Serial# 10/88M-5312-4728 Voltage: 460/60/3 phase Amps: 21.7 Wiring diagram # 2-9000-0026 Was removed from service in November 2020

This is a 2019 saw that was deliver new in 2020. Everything is in good working condition and ready to ship. 18’ length of infeed 14’ max board length 35’ outfeed Includes: One kicker. More can be added. 480v 30 Amps

2001 Grecon Dimter OptiCut Model 200-4R S/N 0667.10

DMC Unisand 2000 43" Wide Belt Sander Includes: Murphy Rogers Dust Dust Collector

DMC SD30 Composition RCS 110 230 volt - 3 phase Frequency 60 hz "B" version for RCS 95 - RCS 110 Electronic readout in "inches" RA grooved steel calibrating roller, 1st group Feed belt speed controlled by inverter with 0,75 kW (1 Hp) 18,5 kW (25 Hp) main motor Automatic device for feed belt tracking and tensioning

2001 Doucet EM2 End Matcher

Good Condition 3 phase .5 HP motor

DOUCET 12-SECTION Clamp Carrier (Hydraulic)Specifications: -- (12) Sections, 8-1/2' width, -- (9) Clamps per section (108) clamps total, -- 36" Clamp opening (rapid change) with 2-1/2" high jaws.Complete with: -- 5 HP hydraulic power pack and motor for rotation -- Hydraulic clamp tightening; -- Pneumatic overhead panel flattener.Note: Tear down not included

Doucet Clamp Carrier Model SRH-40-8.5-240-36 40 Section Clamp 8.5' Wide (240) 2-1/2" x 36" Clamps - Rapid Change Voltage: 480/3/60

- 16.5' long - 16 rotating arms and a total of 288 - 32" clamps

DOUCET CLAMP CARRIER 30 SECT X 8 FT 6 IN WIDE (200+) 36" CLAMPS MODEL SRH-1 SX30- 8.5-240-36 SN 87-10-28 Includes: HYD PWR PACK, PANEL FLATTENER Dismantled and ready to load!

DOUCET MFE 300 Lateral chain feeder for moulders and optimizers -- 3'0" x 16'-0" working deck for material length 2'0" - 16'0"; width 2" to 9.5" and thickness 1/2" to 4". -- Feed system: Hydraulic variable speed 50-300 FPM with a 20 HP power unit. In-feed (4) roller accelerator; (2) top steel rollers and (2) bottom drive roller. Additional idler rollers along feed fence to support lumber during feeding. -- Chains: Transport length of lateral chain feeder 3'0". (8) strands of C2060 chains on pneumatic up/down device to release lateral pressure on board when feeding. -- Pedestal: Feeder controls mounted to pedestal with extended cable. Interface relay to stop feeder when moulder is stopped. -- Adjustments: Tool less adjustment handles for quick setups. Easy access to for thickness adjustments at front side of feeder. -- AVAILABLE OPTIONSOne (1) set of four (4) feeding wheels made of steel with hardenedsurface teeth $ 1 000.One (1) set of four (4) feeding flat wheels made of steel, 2" wide insteadof 1" for wide material feeding $ 500.One (1) set of four (4) feeding flat wheels made of steel 1" wide $ N/C.Guiding Tunnel between feeder and moulder,Standard Guiding Tunnel (4' long) $ 1 650.Standard Short Guiding Tunnel (32" long) $ 2 100.Complete Guiding Tunnel (4' long) $ 2 700.Complete Guiding Tunnel with adjustable fence (4' long) $ 3 800.Motorized Guiding Tunnel (4' long) on request.Additional chain transfer length capacity (up to a maximum of 6additional feet) For MFE-300-16 sold per foot $ 1 685. Note: More than 6 add. feet: price upon requestSteel plates between chainsFor MFE-300-16 $ 1 050.Platen chains recommended for softwood speciesFor MFE-300-16 $ 2 850.One (1) additional chain for shorter material down to $ 1 750.18" min. lengthPressurized lateral guide with roller bearing end $ 1 400.Powered lateral guide with roller and side guides on request.Custom working height on request.

Doucet MSP-CR-19-48-15-TRF-C-8-7 Conveyor

DOUCET - 16-Section: Clamp Carrier; 16-1/2' Wide(16) Sections with: 16-1/2' wide usable clamping width.Complete with: -- (12) Clamps per section (total of 192 clamps). -- 48" Opening clamps: 3-1/2" High x 4-1/2" jaw width. -- (1) Pneumatic panel flattener. -- Heavy-Duty, 5 HP hydraulic pump for rotation drive. -- (1) Hydraulic torque wrench clamp tightener.Actual model: SRH-16-16.5-19+2-48RNOTE: Tear-down not included.