Woodworking Equipment For Sale

VITAP ALFA 35T Boring Machine (Construction/Line) Specifications: -- 35-Spindle boring head on 32 mm centers, drills vertically from bottom-up and head rotates to horizontal position for edge boring, head rotation is pneumatic with switch control. -- 2-3/4" Max. drilling depth, 3 HP - 2,800 RPM motor, pneumatic drill head advance with speed control. -- Head height adjustment with mechanical digital readout; 34" x 20" table size, max. workpiece width 31-1/2". Equipped with: -- Left & right side fences for construction boring, (2) pneumatic holddown clamps, line boring fence w/flip stops. -- Pneumatic foot pedal control, magnetic starter & overload protection, and (1) set of quick-change chucks.

Vitap Forma Boring Machine 21 Vertical Spindles 21 Horizontal Spindles Approx $1000 worth of carbide bits DUAL LINE machine and there are (2) vertical lines of 21 spindles each for a total of 42 ...... PLUS an additional single line of 21 horizontal spindles!

VALPATO LBK-150-ST 1 Feed Through Profile SanderTECHNICAL FEATURES: An added small needle type drum sander can be fitted with drum sanding aggregates of 25, ­30, ­35,­40, ­45 ­50 mm diameters which can be used for tighter curves and smaller radius sanding requirements. Storage compartments (2 in total) are located on each machine extremities, these are easily accessible and can be used for sanding belts and various tooling storage. Sanding belt motor power: 3 Kw Abrasive head motor power: 1.5 Kw Oscillation motor power: 0.38 Kw Feed motor power: 0.75 Kw Motor power for electrical adjustment of sanding group: 0.19 Kw Machine voltage: 480/3/60 Full Load Amps @ 480V: 15A Compressed air: Not required Dust collection requirement one (1) only 6" (150mm) port: 950 CFM Sanding belt speed: 14 Mt/sec Variable speed of the belt: from 5 to 25 m/min Sanding belt dimensions: 150 x 2640 mm Height of working table: 930 mm Dimensions of front working table: 1980 x 250 mm Machine dimensions: 2500 x 900 x 1600 mm Net weight: 1000 KMAIN FEATURES: User friendly PLC touch screen control panel is accessible from 360° by the operator, the control panel is centrally located on the infeed end of the machine. Factory installed variable feed drive (VFD), enables machine to run from 5 M/Min to 25M/min (+/­ 80 ft/Min). The entire sanding plenum rise and fall is motorized, it can be adjusted vertically in height to utilise the full height/width of the sanding belt. An oiling unit ensure long life of sanding plenum rise and fall master cylinder.

Vonnegut M9 4 Head Planer/Moulder Serial# 8364, 8" Wide Planer Heads

VOORWOOD - A 515 GH, ...Arch Door Sander with Floating Head ARCH SANDER with: (4) 1.5 HP Motors for precision sanding; quality sanding using Disc sanding at continuous feed. Equipped with: -- (4) Floating Sanding Stations equipped with: 1.5 HP Precision balanced drive motors and quick change spindles. -- Infeed & outfeed (1st and last) spindles equipped with: Double collets and angular, horizontal & vertical adjustments with accurate and repeatable digital readouts. -- PLC Control with: Monitor at eye level height.Feedthrough Arch Machine capable of sanding arch profiles on cabinet door components, plus can do straight cuts.. .

VOORWOODM 15 CNC Round End Tenoner & Mortiser --The "M15" Miter Machine is designed to rapidly make mortise and tenon cuts at 0°, 45°, and 90° degrees. Parts can be up to 1.5” thick and up to 4” wide, and of ANY length. --A primary application for this machine is for miter cabinet door frames. Parts can be quickly transferred from left to right. They are mortised on the left side of the machine and tenoned on the right. The machine can also mill the slots. --Specifications & Equipped with: -- The mortise station has (3) servo-controlled axes (X, Y, and Z) that are coordinated by the machine controller to achieve complex CNC motion. It is equipped with a collet-style router spindle for cutting. The tenon station uses the same X- and Y-servo-controlled axes as the mortise station and is configured for pneumatically actuated in-and-out movement along the Z-axis. The tenon station is equipped with a direct drive shaper spindle for cutting. -- -- Pneumatic clamping assemblies with non-marring urethane pads are mounted to the hold-down assembly to secure the parts during cutting and these can be adjusted to various locations over the cutting surface. -- -- M15 Miter Machine operator interface consists of a colored touch screen. For simplicity, the entire calibration, setup, and monitoring of the machine are accomplished using only four touchscreen displays. The program designs the depth and location of both the mortise and the tenon. When the design is complete, it is saved in a recipe format. Once this recipe is opened, the operation is as simple and boils down to feeding the substrate into the machine. -- -- The full-color touchscreen panel is located on the front of the machine to provide easy access for setting up or operating the machine. Clamping and shaping operations are controlled by operating lighted pushbutton switches. --Also Included: --÷Additional tooling (worth $3,500) --÷ Replacement motr (worth $975) --÷ Few small replacement parts

VOORWOOD M 15 CNC Round End Tenoner & MortiserThe "M15" Miter Machine is designed to rapidly make mortise and tenon cuts at 0°, 45°, and 90° degrees. Parts can be up to 1.5” thick and up to 4” wide, and of ANY length.A primary application for this machine is for miter cabinet door frames. Parts can be quickly transferred from left to right. They are mortised on the left side of the machine and tenoned on the right. The machine can also mill the slots.Specifications & Equipped with: -- The mortise station has (3) servo-controlled axes (X, Y, and Z) that are coordinated by the machine controller to achieve complex CNC motion. It is equipped with a collet-style router spindle for cutting. The tenon station uses the same X- and Y-servo-controlled axes as the mortise station and is configured for pneumatically actuated in-and-out movement along the Z-axis. The tenon station is equipped with a direct drive shaper spindle for cutting. -- Pneumatic clamping assemblies with non-marring urethane pads are mounted to the hold-down assembly to secure the parts during cutting and these can be adjusted to various locations over the cutting surface. -- M15 Miter Machine operator interface consists of a colored touch screen. For simplicity, the entire calibration, setup, and monitoring of the machine are accomplished using only four touchscreen displays. The program designs the depth and location of both the mortise and the tenon. When the design is complete, it is saved in a recipe format. Once this recipe is opened, the operation is as simple and boils down to feeding the substrate into the machine. -- The full-color touchscreen panel is located on the front of the machine to provide easy access for setting up or operating the machine. Clamping and shaping operations are controlled by operating lighted pushbutton switches.Also Included: -- Additional tooling (worth $3,500) -- Replacement servo motor for up and down movement(worth $975) -- Few small replacement parts

WADKIN "GA-220" 5-Head Feed Through MoulderSpecifications: -- 5-Head, with 8-5/8" x 4-5/8" cutting capacity (220 mm x 120 mm) -- 40 mm Spindle diameter with cutterhead speed of 6,000 RPM. -- Head sequence: Bottom 10 HP, Right 7-1/2 HP, Left 7-1/2 HP, Top 15 HP, Bottom 10 HP motor. -- 2 HP variable feed speed 19 to 72 FPM, chain drive. -- Currently wired for 460 Volt, 3-Phase power.

7 Spindle Moulder with Manual Bed Lubrication 6000 RPM Spindle Speed 19-91 F/Min Feed Speed Will Take 7" x 5" Lumber Specs: 1ST BOTTOM--7.5 HP 1ST FENCE SIDE--7.5HP 1ST LH SIDE--10HP 2ND FENCE SIDE--7.5 HP 1ST TOP-15HP 2ND BOTTOM-10HP UNIVERSAL-7.5 HP FEED DRIVE--3 HP BEAM LIFT--.5 HP

WADKIN - K 23, ...6-Head Feed Through Moulder Head Configuration --(B-R-L-T-T-B) with working capacity of 9-1/2" x 5".Specifications: -- Head sequence: Bottom 10 HP, Right & Left 20 HP, Top 15 HP, Top 20 HP, Bottom 15 HP motor. -- Spindle dia.: 1-13/16" at 6,000 RPM. -- Mechanical digital readouts on all heads. -- Top heads with MDR for chipbreakers and pressure elements.Equipped with & Features: -- Infeed Table: 2 M (6-1/2'), adjustable table plates for vertical spindles. Includes: Top driven feed rolls , motorized overhead feed beam with dual speed for rise-and-fall, full Cardan feed drive with independent adjustment to feed rollers after top head. -- Side pressure opposite right side head. -- Spindle locks for axial adjustment. --Manual bed lubrication. -- Feed drive: 4 HP Motor, variable feed speed from 20 - 75 FPM.

WADKIN JTA Disc & Bobbin SanderCombination machine with Disc Sander & Vertical Spindle Sander mounted on a common base.Disc Sander Specifications: -- 30" Dia. cast aluminum disc, 4 HP motor, slotted steel side table 38-1/2" x 15", tilts 10° up and 45° down, move in-and-out & up-and-down by hand wheels. -- Equipped with: Magnetic controls, dust outlet and large hand wheels for easy adjustments on worm & rack.Vertical Spindle Sander Specifications: -- Heavy Duty 1-1/2 HP - 1,725 RPM oscillating spindle, 1-1/2" oscillation travel, (75) oscil./Min, mounted on large trunnions and integrated into a 24" x 24" cast iron table, table tilts 30° down & 10° up, 39" working height. -- Oscillation by Heavy Duty worm & gear mechanism.Equipped with: Precision ball bearing for quill, hand wheel table adjustment.

WADKIN GD 220 6-Head Feed Through MoulderSpecifications: -- Working capacity: 230 mm W x 130mm H (9.06" W x 5.12" H) Timber admitted, 220 mm W x 120 mm H (8.66" W x 4.72" H) Finished timber. -- Head Sequence: Bottom 7-1/2 HP, Right 7-1/2 HP, Left 7-1/2 HP, Top 15 HP, Bottom 10 HP, & Universal 7-1/2 HP. -- Spindle dia. 40 mm (1.57"), Spindle speed 6,000 RPM. -- Variable feed speeds 6 - 22 MPM (20 - 72 FPM).Equipped with: -- Right, Left & Top heads with Mechanical digital readouts. -- 1/2 HP Motorized feed beam, 2.2 kW Feed motor, 3 HP Cardan drive, Reverse feed, 5-1/2" Dia. Hardened & Chromed steel feed rollers up to top head, 2" x 2" Polyurethane feed rollers after top head, All feed & pressure rollers move with rise & fall of feed beam. -- 2 M (78.74") L Infeed straightening table. -- Manual bed lubrication. -- Sound enclosure.

Wadkin K23 5 Head Moulder Largest Motor is 20HP S/N 99/2093 440 Volt 3 Phase Electric Motors

Great Condition 500 RPM Spindle speed 8 Head with jointers 1-13/16" Spindle Diameter, Belt Driven 2 bottom cutter heads with jointers-15HP/15HP 2 top cutter heads with jointers--20 HP/15HP 2 right hand cutter heads with jointers--10HP/10HP 1 left hand cutter head with jointer--10HP 1 universal cutter head--10HP

Wadkin 5 hd Moulder, 480v, 9in W Capacity

Model GD-220-5 220 volt three phase, 60 hz, 67 amps Max workpiece admitted 230 mm x 130 mm (9" x 5") Max workpiece finished size 220 mm x 120 mm (8.66" x 4.72") 10-1/2" wide x 77" long adjustable height infeed table 1" high adjustable infeed fence 40mm Spindle dia. - 1st head: bottom horizontal spindle 7-1/2 hp, 208-230/460 volt three phase drive motor - 2nd head: right hand vertical spindle 7-1/2 hp, 208-230/460 volt three phase drive motor - 3rd head: left hand vertical spindle 7-1/2 hp, 208-230/460 volt three phase drive motor - 4th head: top horizontal spindle 15 hp, 208-230/460 volt three phase drive motor - 5th head: bottom horizontal spindle 10 hp, 208-230/460 volt three phase drive motor cardan feedworks Mechanical digital readouts on chip breaker and axial adjustments Sound and safety enclosure with lift up hood around all heads Interior cabin work light 3 hp, 208-230/460 volt three phase feedworks drive motor Variable speed feed with 20 to 75 ft/min range Push button motor controls

Six Wadkin moulders available. Have not been run in a few years. Selling all as one package. - (4) 4-Head machines - (2) 6-Head machines

Wadkin GA 5363 5 Head Moulder

Manufacturer’s Specs Model GD-220-5 220 volt three phase, 60 hz, 67 amps Max workpiece admitted 230 mm x 130 mm (9" x 5") Max workpiece finished size 220 mm x 120 mm (8.66" x 4.72") 10-1/2" wide x 77" long adjustable height infeed table 1" high adjustable infeed fence 40mm Spindle dia. - 1st head: bottom horizontal spindle 7-1/2 hp, [208-230/460](tel:208-230/460) volt three phase drive motor - 2nd head: right hand vertical spindle 7-1/2 hp, [208-230/460](tel:208-230/460) volt three phase drive motor - 3rd head: left hand vertical spindle 7-1/2 hp, [208-230/460](tel:208-230/460)volt three phase drive motor - 4th head: top horizontal spindle 15 hp, [208-230/460](tel:208-230/460) volt three phase drive motor - 5th head: bottom horizontal spindle 10 hp, [208-230/460](tel:208-230/460) volt three phase drive motor cardan feedworks Mechanical digital readouts on chip breaker and axial adjustments Sound and safety enclosure with lift up hood around all heads Interior cabin work light 3 hp, [208-230/460](tel:208-230/460) volt three phase feedworks drive motor Variable speed feed with 20 to 75 ft/min range Push button motor controls

Please see full specification in documents section. Number of vertical drilling spindles 25 Vertical drilling spindle power 2.7 kW/3.5 HP Vertical drilling spindle speed 1,500 to 7,500 rpm Number of horizontal drilling spindles 6 Horizontal drilling spindle power 2.7 kW/3.5 HP Horizontal drilling spindle speed 1,500 to 7,500 rpm X-axis grooving saw power 2.7 kW/3.5 HP X-axis saw rotation speed 2,000 to 7,500 rpm Saw blade diameter required 100 mm/4” ATC router spindle power (power constant from 9000 rpm to 18000 rpm) 9.0/12.0 kW; 12.0/16.0 HP ATC router spindle speed 1,200 to 24,000 rpm Tool magazine capacity 2 x 8 tools HSK63 tool holders supplied 4 Collets for HSK63 tool holders 4 Number of panel support benches 8 Number of vacuum pods per bench/total 3/24 Number of panel feeding rails 6 Vacuum pump capacity 100 M3/hr Length of machine 7580 mm/24’ 10” Width of machine 4650 mm/15’ 3” Height of machine 2820 mm/111” Working length 4250 mm/167” Working width - support bench width 1500 mm/59” Max. panel thickness 125 mm/4.9” Machine weight 6200 kg/13,700 lbs. Max. drilling depth for through holes 55 mm Axis stroke/positioning speed X-axis 5050 mm/80 M/min Y-axis 2150 mm/60 M/min Z-axis 370 mm/20 M/min C-axis 0-360°