Equipment For Sale

Used Hydraulic Conveyor Belt System - Complete! Belt is 18" wide by 14' long. Large infeed hopper. Raise, lower, pivot & folding controls. Great for cement or sand. $11,000 or best offer. Located in Cheshire, CT. Call Sal or Jack at 1-800-872-5726, 203-271-1682 or email [email protected] if you have any questions

Salsco 60" Electric Shaving Mill Includes:Chip sizer/breaker

Salsco 60 " Shaving Mill Diesel engine Stationary Mill Seller believes it is a 2009 or 2010. There is 10 knives ( 5 rows with 2 knives each)

SALVADOR - SUPERANGLE 600, ...Pusher Chop Saw. Provides complete chop to length & optimization of wood strips including the elimination of defects. -- Infeed is made of Heavy-Duty steel frame; working height: 1,000 mm (39") from floor level; safety provided by a light curtain. -- Pusher slides on double hardened rails. -- Reading Operation: Uses (2) Sensors: (1) for overall length and the other to read the crayon marks. -- Transmission of power: From motor to the carriage; accomplished by a 50 mm wide steel reinforced toothed belt. -- Part held in place by (2) aligners before & after the blade; insures a square cut. -- Saw box area: Enclosed by interlocking steel cover with a large window for clear view; Saw travels through an aluminum table insert that can be easily changed as needed; High Efficiency motor, IE3 rating, helps keep power consumption at a minimum. -- Technology: Operating software: Customized Windows-based program; designed to be intuitive and specially designed for optimization of the wood. -- Large 19" monitor at operator eye level; PC set up with: SSD Double hard drive with 2nd being a clone to have and be ready to back up in the machine. -- Cut lists: Can be uploaded remotely by network connection or flash drive; chop length optimization can be set for minimum waste priorities. -- Optimizer supports defecting crayons, as well as up to 5-grade qualities. -- Electronics: Multi tap transformer steps down higher voltages; 460 - 600 to the voltage requited by the machine. -- SP 15 Magnetic Strip Measurement: Technology improves positioning from basic encoder standards to absolute measurements of +/- 0.1mm. -- Outfeed: 0° Belt and (1) PC double ejector. For applications of many workpieces cut at angles, it is best to eject the workpieces together with one large rack & pinion ejector. Workpieces are pulled from the Saw on an outfeed belt. - Once the parts are clear of the Saw, the large ejector manages all cuts in 1-push onto the steel table for collection. WORKING CAPACITYMaximum board length before cutting: 5,100 mm (16').Minimum board length before cutting: 500 mm (19.6").TECHNICAL SPECIFICATIONSMain saw power: 15 HP.Saw blade specifications: SA600; Max. 00 mm; dia. bore 35 mm.Maximum pusher reading speed: 60 MPM (200 FPM)Maximum pusher pushing speed 60 MPM (200 FPM)CUTTING CROSS SECTION &#9679 0°: 100 mm x 360 mm / 160 mm x 310 mm. &#9679 +/- 45°: 100 mm x 260 mm / 160 mm / 220 mm. &#9679 +/- 70°: 100 mm x 120 mm / 160 mm x 100 mm.Minimum: 15 mm x 30 mm.Number of cuts within last 40 mm of board One: (1)Maximum workpiece weight: 110 kG (242 Lbs).Power Requirements &#9679 11 kW. &#9679 Primary supply voltages: 220/380/420/440/460/480/560/580/600 V.Pneumatic Requirements &#9679 Compressed air supply: 600 - 800 kPa (6 - 8 bar). &#9679 Maximum air consumption: 300 Nl/min.Dust Extraction &#9679 Intake diameter: 160 mm Upper; 120 mm lower/ &#9679 Extraction System Collection speed: 28 M/s. &#9679 Dust Extraction Capacity: 1

2018 Salvador SuperCut 100 Automatic Crosscut Saw PRICE REDUCED

Punches, shears amd bends sheet metal totally automatically without any intermediate handling. Feeds with tower as pictured. CNC controls 460 volt 3 phase Recently replaced parts: - Complete punch head assembly - P2R assemblies (2) - Servo Motors for P2R (2) - Complete Drive – Power Supply - Loading Belts on material tower - Low Pressure Hydraulic Pump - High Pressure Hydraulic Pump - Electric Motor for Hydraulic Pumps - Water Chiller - Shear Blades - All Accumulators on hydraulics Available Early September 2023

SAMUEL TANK-660V-150PSI 660 Gallon Air Receiver660 Gallon Vertical Air Receiver Tank. • Diameter O.D./I.D.: 42 O.D. • MAWP: 150 PSI @ 400° F • MDMT: -20°F @ 150 PSI • Capacity: 660 Gallons • Pressure: 150Support & Attachments: • 8 Base Ring • Safety Valve & Pressure Gauge - 700/MCTK-SW10-150Recommended Option: Zero Loss Compressed Air Condensate Trap w/WindowPowers through Condensate buildup and Ideal for Compressor applications up to 100 HP (500 SCFM).Ideal for inline filters up to 5000 SCFM. • The WaterHog™ design avoids small passages common on competitor designs, ensuring clog-free operation. • Fully Automatic Operations. No timer or manual settings • No Electrical Connections. WaterHog™ is powered by compressed air, avoiding the need for electrical wiring and connections. • Energy Saving Operation. Zero compressed air loss when properly installed with balance line. • Check with your utility to see if it qualifies for energy efficiency incentives. • WaterHog™ pays for itself when replacing open condensate drain valves or timer traps. • Low Profile. • The 4.7" vertical operating height allows WaterHog™ to fit where other larger units can't. • Max Operating Pressure: 200 psig • Min/Max Control Pressure: 40/130 psig • Min/Max Temperature: 34/170 F • Inlet / Outlet Connections: 1/2 inchPrice ...$ 450.00 (2) Year Warranty Included

Samuel Rogers 66" Knife Grinder

KENT - Single Head, ResawSpecifications: -- 15 HP Motor. -- Blade size: 168"; x 1"; x 0.035"; 2TPI. -- 6" Wide feed belt. -- Operational working heights: 1/4" minimum cut to 8"; maximum. -- Feed speed: 20 - 150 Feet per minute.

Sanborn Machinery RH 8 Saw Drop Saw Trimmer with Hydraulic Drive

Like new 36" vertical linebar resaw. COMPLETE WITH RUN AROUND SYSTEM. Saws 14"W x 16"H x 12'L cants (can be extended). Operator's cab w/ controls. Elec. sys. w/ starters, prewired mach. Pre-plumbed hyd. sys. 20HP hpu, sub-steel, ten saws incl. Mach. disassembled. Crane additional. $90,000. OBO

Sanborn 6' Left Hand Double Cut Band Head Rig on 17 Degree tilt

Sanborn 5' Band Head Rig Air Strain w/ 100HP Electric Motor

2000 Sanborn Min Max This is not a whole mill. - Two complete good working Silvatech Set works , - Four Heavy Duty Head Blocks . Board Dogs, Cant Dogs, Turners and Tapers all Hydraulic. These were custom built super heavy duty for this mill . Very well cared for. Great care taken in the removal. - Every thing is under cover. - It’s the complete system with everything you need to put it back together, all labeled and photos. - The spare set works was near new when bought. - Everything is on heavy duty pallets can be shipped. Call 800-459-2148 for more info.

1984 Sanborn Min Max Wide Band Sawmill with Live Deck. Detroit 271 engine with the largest injectors that are made for that engine. It starts and runs well. Includes: hydraulic drive 3 chain live deck that is about 16' long and 12' wide with a stop and loader and arms that go across the bed of the mill. The logs must be rolled across the arms to the 4 head blocks. The frame of the live deck is mounted on 3x3x3 concrete cubes. set of 4 large head blocks with the same design as the original but which are about 12" large capacity than the originals. 40 foot long 3 chain green chain with new hydraulic motor and large gear reduction unit, 3 saw Chase 24+" edger with a 271 power unit that starts and runs well. 7 bands here and another 5 being repaired. Maintenance and Repairs Done: - balanced both wheels, reground both wheels - removed some weight from the upper wheel - added a weight strain system instead of a small spring - added vibration damping connections - provided electric shut off and throttle to the engine - added an auxiliary open center hydraulic pump and valves. The pump is driven off the front of the crankshaft of the engine - replaced the bearings throughout the mill - strengthened the take away table to take very heavy loads - installed a new set work screw system - removed the pantograph for hydraulic supply and replaced it with an igus hose and cable carrying chain Call 800-459-2148 for more info.

This mill has been damaged, but if you want good parts there are some here. Call 276-472-2199 for more info.

SAND-RITE DB-612 DLX Sander with Heavy Duty Cast Iron StandCustom ordered to fit your requirements with quick 3 week lead-time!Specifications: -- (1) 6" Diameter x 7" Wide pneumatic drum head , which allows the operator to regulate how firm the sanding head needs to be to conform the head to what they are sanding. -- Motor: 3/4 HP -- (1) B-12 Brush Head, which allows the sanding irregular surfaces with out loss of shape. -- And matching Heavy Duty Cast Iron Stand.

SAND-RITE DUO-DLX Spindle Sander; Horizontal spindle sander with 3/4 HP BALDOR motor. -- Optional brush heads sand irregular surfaces with out loss of shape, and the optional pneumatic drum heads (available in 2" to 8" diameters) allow the operator to regulate how firm the sanding head needs to be to conform the head to what they are sanding. -- Price does not include the stand - Add $308.00 Cast iron stand."Drums, brush heads, and sleeves are additional".Brush Head: ADD $ 175.00 2" X 8" pneumatic drum: ADD $ 140.008" X 9" pneumatic drum: ADD $ 302.00 Special note: 220 grit is the finest grit supplied for Brush Head

SANDINGMASTER - KSB-900, ...Single Head Wide Belt Sander36" Width cap.; combination sanding head.Head: Rubber covered spiral grooved contact roll & finishing platen.Specifications:15 HP Main motor.37" x 75" Abrasive belt size.Electronic tracking and air tensioning of abrasive belt.Rubber covered infeed & outfeed holddown rollers & holddown shoes.Variable feed speed 15 - 45 FPM via 1.5 HP motor.0" - 5" Manual part thickness opening.Includes: Optional floating bed for sanding fine veneers.Equipped with & Features:Extended infeed.Load meter.Disc brake on main motor.Safety stop bar.

SANDINGMASTER SA3300-900 TRIPLE HEAD WIDE BELT SANDER3-Head, 36" max. width cap. - 1st Head: 11" Dia. rubber covered contact roll, 24 HP motor; 2nd Head: 11" Dia. rubber covered contact roll, 18 HP motor; 3rd Head: Combination head with rubber covered contact roll and finishing platen, 18 HP motor. 37" x 75" Abrasive belts with electronic tracking. -- 2-Speed conveyor feed, 23 & 46 FPM, 1.0/1.7 HP motor, 0" - 6" motorized part thickness with LED readout, a joystick lever controls raise and lower of feed bed and start and stop of conveyor belt, also includes "SP-Matic" automatic part thickness setup. -- Thin veneer sanding package with rigid table setting for solid wood dimensioning and floating table setting for veneer sanding, infeed and outfeed spring loaded holddown shoes. -- Includes: Motor load meters, electronic brakes on sanding heads, infeed safety shutoff bar and 18" infeed conveyor area. Actual model "SA-3300-900".