MLS Number 10830384 1996 Chevrolet 2500 Mechanic / Service Truck 138,665 miles New battery No AC

1991 Chevrolet Kodiak Truck 366 big block Fuel injection gasoline 5 speed 105k miles Runs great 25000 g.v.w.

Clark 664 Cable Skidder 353 Detroit Automatic tranny Gearmatic 19 winch Pins are tight 18.4-34 tires Woods ready

1987 Clark Gooseneck Trailer 44’ Long x 10’ Wide 70,000 lb. Capacity Good Tires and Brakes Ramps Road ready Current valid inspection

F667 Clark ranger Runs and operates good Needs blade cylinder and rear wheel seal replaced Cummins 5.9

1984 Clark blue 40 ton log trailer Excellent condition Good tires Good brakes Good straight frame 8 foot bunks x 4 New 5th wheel hitch has been installed. This trailer is job ready Clean title in hand Went to end dump trailers and no longer need

MLS Number 12231702 2011 Clarke's Industries Bag House ? Explosion doors ? Abort gate at outfeed ? Abort gate at infeed ? Backdraft damper at infeed ? Spark detectors on infeed and outfeed lines ? Airlock ? Backdraft Damper on dust outfeed line ? Deluge System This baghouse is fed from a fan that has suction from Edger, 6”-10”-12”-20” Ukiah (chip/saw) and 20” sawbox. The sawdust from the discharge line under the airlock of the baghouse is sucked into Discharge blower (See Item#2). The dust outfeed line at the middle of baghouse, which discharges the dust fines during the cleaning cycle of bags, returns the fines to the baghouse fan. The Baghouse supplies air back into the building. This baghouse is fed from a fan with following specs: OEM & Model: Clarke’s Industries, Model MH-11, Serial 11OCWUBI3923 Driver: TECO 350 HP, 1785 RPM, 5009C Frame Motor Capacity: 66000 CFM Spark Detection Control System OEM/Model: Clarke’s Industries, Pyroguard CXC-2 Buyer responsible for dismantling.

2023 CMI C300 Mulcher -590 hours -Warranty -Like new Turn Key

MLS Number 11922341 Denis Comact 948 Gang Saw Edger 6" infeed table Spare guides

Denis 948 Gang Saw

MLS Number 10679774 Cook Grade Lumber Resaw 30 HP Will saw 16" wide No return 1 1/4" to 2" blades

MLS Number 11413038 Cooper Overhead End Dogging Scragg With Debarker And Gang Edger Transfer Chain Conveyor x 60’, H82,1-7.5 HP 480V gear drive 54" Cut Off Saw, 20 HP 480V motor, hyd stop gates, 20 HP hyd pack 4 strand x 12' long Debarker In Feed Deck, 5 HP 480V gear drive, H78 16” wide x 19’ long log haul belt conveyor (driven from debarker in feed tire drive) Cambio 24" Debarker, 75 HP 480V drive, spiked in/out feed rolls 20 HP 480V drive 3’ wide x 36’ long hour glass rolls transfer, 7.5 HP 480V gear drive 5-strand Scragg in feed deck x 20', H82, hyd log stop loader, 7.5 HP 480V gear drive Cooper Overhead Scragg Mill, 30 HP 480V 150 gal hyd package, variable speed cable drum feed works with pantograph arm Log positioning rolls on infeed w/ double overhead dogging system, 48” dia. saw husk(125 HP 480V each saw), setworks control 2-18” wide 2-position slab and side board belt conveyors, operators control cab w/ controls, camera and monitor for centering log 8-16’ length capacity, maximum log dia. 22”, largest square cant 12” x 12”, smallest square cant 4” x 4” 5-strand lower camel back landing transfer x 9’-6” long, 4-strand hyd lift transfer to gang edger and cant center bypass Center bypass rolls and belt conveyor to edger out feed landing transfer 10” mainland gang edger w/ 200 HP 480V drive,34” inserted tooth saws with 5/16” kerf(24 spare saws with collars), 2-2-2-4 spacing 6” x 50” mainland board edger w/ 150 HP 480V electric drive, 24” inserted tooth saws with 5/16” kerf, 8”-4”-4”-10”-6” pockets, 7-individual actuated self tailing belt conveyor out feed c/w splitters Camel back transfer,4-strand x 27-1/2’ long, H78B, 5 HP 480V gear drive 2-Saw Trimmer, 4-strand x 10’ long, 16’-4” between 20” dia. saws,10HP 480V drive on feed works and saws, 16” wide x 28’ long out feed belt conveyor, 5HP 480V gear drive 4-strand x 26’ long H78 camel back transfer w/ 5HP 480V gear drive

MLS Number 10791171 Cornell 24" Chop Saw All live rollers 16' infeed 8' outfeed Sold as is.

?Cresswood EF-60 Grinder 100 HP 60” Wide Feed Opening Includes 60”W Vibrating Conveyor (shaker table)

Cresswood Model EF 50-100A Horizontal Shredder 100 HP 12' Vibratory Conveyor (2) Feed Rollers Screw Auger Discharger Inclined Conveyor with 10" Magnetic Head Pulley Discharge Height 116" Crossbelt Magnet Soft Start Extra Set of Cutters 2 New Screens 1/2" Screens

CSI PTD 264 Delimber One owner Good 11-22.5 tires Good bar and chain Work ready SN 26406101069 REDUCED PRICE

CSI 4400 Bucksaw 18' long frame 59" bar 4600 hours of use

CSI 264 Delimber Came off a Deere 437 loader STOCK IMAGE PHOTOS COMING SOON

Dangle Head 3/4 pitch chain 37” bar. 26” cut in a single pass 35” cut with multiple passes remove the top, forks, big limbs also shovel log the tree stems Rebushed Cylinders repacked

02 CSI PTD-143 Delimber -3 knife delimber -Works as it should Price is obo