930K Caterpillar wheel loader, 2014 with 12798 hours, bucket and forks included located in Tazewell, VA Contact Zach Kittrell for more information. 931-224-0699 Well Maintained and ready to work for you.

Chase Turbine Mfg. Co. Sawyer's Favorite hand set sawmill, immaculate condition (3 HB), wood & steel frame, 40' track, in track mount carriage drive drum & cable, 100 HP 220V head saw motor w/ WEG soft start MCC, include off bear belt on husk frame & outfeed belt conveyor, (1) w/ shaft mount reduction drive, Selling with (See Chase Edger under Edgers)ref #204, Contact Jackie 931-698-3342

Chase (2) saw board edger, 30" wide w/ (1) movable saw w/ 40 HP motor 230/460 V 1765 RPM w/ HD spiked feed rolls, (2) inserted tooth saws, outfeed steel deck table w/ bar sweep to transfer board to discharge belt, (Selling with sawmill, See Chase Sawmill under Circular Sawmill), ref #204, Contact Jackie Kittrell 931-698-3342

CM & E 60" HFBD 6 knife chipper (has broken pulley, but may have a possible replacement) (ref# 165) Call Amy for more information 928-723-9449

PRICED REDUCED Cone 2-Saw Independent Arbor Optimized High Speed Edger, 4/4 to 4" runs 14 boards per minute W/ Tailing Device W/ Innovec Generation III Controls W/ Lots of Spare Boards & Parts to Keep Software Running, Includes MIC Unscrambler, with even ender up top. Scanning Bar and hi-speed indexible infeed and tailing belt outfield. On the ground and ready to load. Taken out with Videos and instructions to re-install. A must. Ref #131

Edmiston 48” (4) HB circular sawmill, tong dog, includes chain type log turner, 30 HP hydraulics for carriage & turner, mill cuts up to 24’, includes husk frame w/ top saw, 15’ slab dump conveyor, Tyrone 150 HP shot gun carriage drive (only 4 years old!) w/ Z-Set setworks or can use standard Edmiston setworks, . Seller will remove. (ref #181) Call Amy for more information (928) 723-9449

air exchange horizontal tank mount air compressor, (2) 15 HP dual compressor, Ref #204, Call 931-797-6284 New coupling and electrical switch repair ready to work. Dual Air compressor (2) 15 HP pumps

Air compressor was used in food processing and is very clean, variable feed, 250 HP Seller will load on your truck, ref # 203, Call 931-797-6284 Motivated seller make a good offer

New April 2024 barely used Go Fast MET-20 multi-end trim saw 44 FLA, 10 HP blade motors, 1 1/2 HP feed through motor VFD, includes 12" waste conveyor & 1/2 HP material take away, belt conveyor 12", 20" carbide tip saws - 2060 chain, material spec 12' long x 12" wide x 4 1/2" thick, mounted motor controls, Ref #204, Contact Jackie Kittrell 931-698-3342 Seller will load on your truck

(1) approx. 24" 20 HP Hartzell high speed transfer fan, (1) 56" 150 HP collector fan (ref #173)

Hemco double end trimmer w/ even end rolls, feed through chains & outfeed chains (trimmer can sell with stack and sort line upon request),ref#170,

Hemco Lumber Trim, Stack and Sort Line – (4) strand infeed w/ destacker and waterfall unscrambler board dealer to Hemco (9) station drop saw trimmer w/ controls and block conveyor, Hemco (11) bay lumber sorter w/ 75’ of haul out chain, includes hydraulic power packs, waterfall unscrambler to (4) chain arm stacker, 8’ wide, unground cylinder ground package hoist, stacking stick conveyor included, includes controllers & Dell PC View Sonic screen, Sullair LS-10 tank mount air compressor, Call Amy for more information 928-723-9449 OBO

REDUCED! Hemco Lumber Trim, Stack and Sort Line – (4) strand infeed w/ destacker and waterfall unscrambler board dealer to Hemco (9) station drop saw trimmer w/ controls and block conveyor, Hemco (11) bay lumber sorter w/ 75’ of haul out chain, includes hydraulic power packs, waterfall unscrambler to (4) chain arm stacker, 8’ wide, unground cylinder ground package hoist, stacking stick conveyor included, includes controllers & Dell PC View Sonic screen, Sullair LS-10 tank mount air compressor, ref #170, Call Amy for more information 928-723-9449 OBO

HMC 4800 horizontal resaw. This saw is made by Pinheiro for HMC, quality and speed 4" -5” band, includes. New electronic setworks, (no conveyors), excellent stand alone machine, Great for relcaiming Slabs (ref #200)

Ingersoll Rand SSR II 50 HP screw type air compressor, believed to have 20,000 hours, Ingersoll Rand Model TS2A dryer 150 PSI Max refrigerant dryer (ref #174), 460V 3 phase, Approximate 220 CFM, Call Rachel for more information 931-797-6284

TC54 John Deere Loader with 4' JRB Quick Couple Forks. (sn: DWTC54H570468) 26,344 hours. Well Maintained. Contact Zach: 931-224-0699

Lumber Breakdown, Dual Grading, Trim, Sort, and Stack System – 45’ (4) strand package deck w/ S-drive & H-78 chain, 6’ (4) arm breakdown hoist (hydraulic w/ HPU) w/ stick removal belt & stick stacker, dual grading stations as follows: (1) top (5) strand common shaft dual drive & (1) bottom w/ (5) strand decline table 20’ grading w/ operator control w/ 81X chain, both w/ operator control w/ 81X chain, Softac software & PLC VASKAWA57 VFD, Lucidyne label jet printer, MIC lumber trimmer w/ double paddle fence, MIC (28) bay bin sorter, (5) arm blade type lumber stacker & Sullivan Palatek air compressor (piston),Specifications: 386' long x 24' high, runs 6' - 16' L longer, thickness 1" - 4" thickness, width 6' wide packs, 3 1/2 - 22" wide packs, 3 1/2 - 22" wide, this system was running December 1, 2023, ref #171 – For More Details Call for Complete Component System

Lumber Breakdown, Dual Grading, Trim, Sort, and Stack System – 45’ (4) strand package deck w/ S-drive & H-78 chain, 6’ (4) arm breakdown hoist (hydraulic w/ HPU) w/ stick removal belt & stick stacker, dual grading stations as follows: (1) top (5) strand common shaft dual drive & (1) bottom w/ (5) strand decline table 20’ grading w/ operator control w/ 81X chain, both w/ operator control w/ 81X chain, Softac software & PLC VASKAWA57 VFD, Lucidyne label jet printer, MIC lumber trimmer w/ double paddle fence, MIC (28) bay bin sorter, (5) arm blade type lumber stacker & Sullivan Palatek air compressor (piston), All controls are in order, This system was running the first of December 2023, ref #171 – For More Details Call for Complete Component System you can run it now. Contact Jackie 931-698-3342

Newman KNO 24 lumber trimmer, (9) station drop saw, will pass rail tie’s, includes waste conveyor & infeed this saw is out and ready to load in your truck. Ref #188

Newman Whitney KNO 24 trimmer, S/N 24120897, will pass a 5 1/2" cant, (9) station w/ individual motors, built-in wood waste block conveyor, used on dry line, good condition (ref# 200). This machine has just been removed It is setting inside and ready to load on your truck.