FOOTE/JONES gear reducer: 70:1; 22 HP. Price $1,500.00. As-is/where-is. (Inv. # G-17).

FOOTE/JONES gear reducer: 70:1; 22 HP. Price 1,500.00. As-is/where-is. (Inv. # G-16).

FULGHUM 36" chipper. HFVD. 6 knife. Includes: old style 75 HP motor, v-belt drive, and blowpipe to load trailers. $7,000.

FULGHUM 620 debarker with 4 sets of 2" wide bull wheels. Includes: Edmiston 3 strand log deck; bark conveyor belt; air compressor; hydraulic power pack. Price $9600.00

HMC Two saw trimmer, Model ET10: Operator on left; NO electric setworks--manually operated hydraulic valve type; standard 10HP electric motors on saw blade; standard hydraulic system; NO belt conveyor. Offered as-is/where-is with no warranty or guaranty, as removed from service.

HOLTEC Lumber  Trimmer. Manually trims bundles of lumber. Trims one end only. Manual setting of lumber bundles required. Bar & guard replaced; hydraulics tested; support frame, including steps, sand blasted and painted; electric motor drive checked; air cylinder and up-down of bar tested; manually operated saw assembly moves about 12". Offered as-is/where is. Price $14,600.00

HYSTER FORK LIFT. Model H135XL, 13,500 LB capacity, PERKINS diesel engine, good condition, 4510 HRS, mast at rest approximately 12' tall, 11.5" wide x 47" long forks, with cab--but no doors. $23,000 OBO.

Digital DC, Band Mill Drive. 300HP GE motor, 500volt, 1150-2000 rpm w/ Eurotherm SSD590 digital controller; 800 amp. main breaker; 72"x72"x24" N12 enclosure w/ A/C; 330KVA isolation transformer. Hugh advantage is infinite speed control & dynamic braking. (For quick saw change and start-stopping).

Package Deck and Tilt Hoist System.  25' long deck with 3 strands of 81X chain, electrically driven with 'S' type reversing drive.  Heavy duty tilt hoist is a 3 arm, hydraulic up/down and tilt movement. 20 HP hydraulic power unit included.  Also included is a seven slide stick conveyor to a panned area which feeds a "V" type, 6 strand unscrambler with electric drive and a 40' long x 12" wide stick belt.  Price $ 18,800.00. NOTE: Will load machinery onto your truck.  Located in Biscoe, NC 27209.

JOCAR BAND SAW: Model 1600/230; very heavy duty rectangular tubing column;  63" diameter wheels with wheel guards; right hand machine;  vertical sawing; 9" face width; kerf approximately .125"; pressure guides;  complete with 125 HP electric motor, drive and guard; hydraulic strain; top wheel tilt and hydraulic power unit.  Price includes loading onto your truck. PRICE $35,000.00. 

MUST BE ORDERED FROM FACTORY. VERTICAL ARBOR SLAB RECOVERY GANGS are designed to process 3 sided slabs into pallet boards. Ten (10) vertical, interior feed rolls are standard. Variable speed feed system up to 175 FPM. 2" automatic cant variance allows both 3 1/2" and 5 1/2" wide cants to be run back to back with no operator involvement or machine adjustments. Machine utilizes one bottom "clean-up" saw to eliminate irregular shaped pieces assuring flat, square pallet boards. 30" to 60" lengths. Can be partnered with a slab edger and trimmer to recover boards with NO operators. PRICES RANGE FROM $185,000 to $215,000 depending on the model and options.

Like NEW heavy duty package deck. 40' OAL, 3 strands, WR132 chain. 194:1 x 25 HP drive. Heavy 8" x 31# H beam runners. Run less than one year. Strands can be spaced as needed or shortened or made into 4 strands by mill.

KOCKUMS chip conveyor. Drive section ONLY with 20 HP drive; approximately 14' long x 42" top of chain to base x 32" deep; formed trough; 3 7/16" drive shaft and bearings. No tail section. WD120 chain. $5,500 OBO.

LIGNA 10" x 48" thin kerf guided gang. Complete with (2) 200 HP motors; two speed feed works; chromed and knurled rollers; splined arbor. In very good condition. Rollers and bearings replaced just prior to removal. No infeed or outfeed. Includes guide milling machine; puck mold; guides form 7/8" to 2"; shims; many saw blades in excellent condition. PRICE REDUCED to $105,000.

LIGNA ALT Trimmer. OPERATOR ON RIGHT. Set up for "0" saw; from 8'  to 16' on 2' increments. Has 4' and 6' saw areas. 7.5 HP motor and saw blade on ladders. 9 feed chains--hydraulically driven. PLC controlled. Includes: operators controls and hydraulic power unit; 2 air operated gates; 5 strand tipple system with dealer wheels and air operated tipple arms; 9 feed chains--hydraulically driven; 5 strand let down conveyor; 5 infeed side, even-end rolls.  Doors need work but are included.  Offered, as removed from service. $36,000.

LIGNA rosserhead debarker, model 848. Complete machine with bull wheels, 50 HP head motor, head with cutter bits, operators controls. Good condition. Offered as-is / where-is but loaded on your truck.

8" x 48" Rosserhead debarker. Used very little, LIGNA Model 848, S/N: F162085. Heavy duty. 6 sets bull wheels mounted on 3 7/16" bearings, 36" on centers - (like new, not re-poured). 50 HP head motor powering 8 section carbide tooth head. Maximum length 20'. Base frame 12" WF beam. (6) x 1 1/2" thick kicker arms., 20 HP Hydraulic system for head traverse and log rotation. Heavy duty pivot system and electric panel included. Size approximately 35' x 9' wide x 7 1/2' tall. Operators controls. Machine in great condition, but has been sitting outside . Offered as-is / where-is and loaded on your truck. Price $36,000.00.

McDonough 54" center split resaw, older, cast-iron version with 50 HP, 220 Volt, 3 phase motor. Resaw uses 6" blades. Wheels have 6 3/8" face. Price $6,800 O.B.O. Call Brian 336-269-1238 for more details and pricing.

McDonough 62" Linebar Resaw S/N 62M: 1.25" thick bottom wheel, .75" thick top wheel, mechanical weight strain, swing door to change saw, 150 HP electric motor and v-belt drive (no belts); Linebar with 3 chromed press rolls, hydraulically driven, Temposonic setworks with cylinder, 5 bed rolls; hydraulic power unit for feed rolls and speed control; Infeed with slab lifters, bed rolls, and air operated cant turners; 14' landing table with rooftop chain; 12' runaround landing table with rooftop chain; 7' outfeed runaround with tipples. Located in VA. Removed from service and ready to load on your truck. $49,000 OBO.

6" X 54" MEADOWS "TITAN" Combination gang-edger with 100HP drive motor, 5 saws on gang side and 18" edger side movement. Door on right. Laser movement. 48" roll width infeed and push button controls. 20 HP hydraulic system. Outfeed belt, 14' long. Very good condition. Price:  $45,000.00