MLS Number 10689968 Globe 5 Head Panel Trim Saw Approximate panel capacity: 8 feet wide X 26ft long Saw was cutting large full size sheets (8ft+ x 26ft) at a particle board manufacturer Lugs on chains have micro adjustment bolt ( brass) Air cylinders raise and drop heads Brands of chain: Woodward & White Overall width: 14 ft. 6inches Overall height: 6 ft. Overall length: 33 ft. 4 inches+-

MLS Number 12543674 Hazlethorn Stake Pointer 240V single phase Air operated control Needs new cutters

Ingersoll Rand Air Compressor 3 phase 10 hp Work ready

54" Horizontal Resaw Wide Blade Excellent Machine 400K Replacement Cost

MEREEN-JOHNSON 424 DC GANG RIP SAW 24 inch width capacity 75 HP arbor motor- 3600 RPM direct drive 5 HP variable speed feed ( new belt ) Four ( 4 ) kick-back finger sets : ( Two ( 2 ) top in-feed, One ( 1 ) bottom in-feed, One ( 1 ) top out-feed ) A new out-board arbor bearing assembly New set of alum bars and rubber slats installed It is wired 480 volts 3 phase . The serial no. is MJ-4709 One saw sleeve and set of spacers ( 6 saw blades ) Cleaned, painted, and checked.

Morbark Chip Blower Hopper Feed Came out Running 10 HP Motor

2018 Morbark 3400XT Wood Hog Horizontal Grinder CAT C18, 765 Hp engine Approx 2100 hours New belly belt/skirting; Rebuilt mill Engine has new cylinder sleeves with rod & main bearings, purge pump & hydraulic fan motor (replaced by manufacturer due to a defect) Remote Magnet 1” & 5” screens Great machine and ready to go to work

2022 Morbark 3000XT Horizontal Grinder -180 hours -575 hp CAT engine -Remote -Still under warranty NEW NEW NEW

2021 Morbark Woodhog 6400xt -3800 hrs -C32 engine -New infeed chains -New infeed floor -New bit holders, racks, rotor pins -Solid grinder ready for work

Murphy Rogers MRM-16-185H Shaker Dust Collector 16” dia. inlet 25 hp exhauster motor 81 filters 6” dia. x 68” lg 668 sq/ft of filter 6,000 cfm estimated capacity Serial Number: 1020

MLS Number 10908375 Newman S-282 Wood Planer Used 18 x 16 S-282 Newman Serial number 14467 Helical 6 knives Length 18” Top head 40 Hp Bottom head 25 Hp 15 Hp HPU Voltage 460

Newman 282 Wood Planer 18 inch wide planning capacity by 6 inch thickness Newman 6 row Quite-cut carbide cutterhead 50 to 75 percent carbide knife life remaining 40 HP 3600 rpm top head motor-DMD 25 HP 3600 rpm bottom head motor- DMD 15 HP hydraulic pump package Feed speeds : 40 to 150 feet per minute Rubber tire feed – one row in-feed and one row out-feed. Dust hood Carbide knife grinder and jointer Cleaned and tested

8 Head Drop Saw 40' x 14' 5 Strand lumber Deck (Infeed) 16' x 5' 5 Strand Lumber Deck (Infeed) 16' x 5' High 8 Strand Unscrambler (Infeed) 100' x 24" Scrap Conveyor (Outfeed) Drag Chain Underneath (Outfeed) 24" Roll Case (Outfeed) Electric Disconnects And Controls Optional 4 Strand Roof Top Transfer Optional 82' Of 5 Strand Lumber Dcck

Northtech Machine NT-GRS-300RF Gang Rip Saw REDUCED Roller feed Max depth of cut is 4". Max width is 12". New Saw Blades And Spacers

2006 Peterson 4710B Tracked -6720 chassis hours -Remanufactured engine installed on machine as the old clutch destroyed the engine -Done by CAT dealer in NC (GregoryPoole) -Reman engine 530hrs -New clutch installed the same time as reman engine installed -Feeder floor 30-40% life left -Rotor balance is good -New main conveyor belt just installed -New main conveyor head motor installed -New skirting guard deflectors installed under rotor -New set of screens in machine I think they are 3" -New clutch module and harness -New Iqan electrical panel upgrade system installed by Peterson rep -C18 T3 caterpillar 755HP -Twin disc clutch Ready to work

2020 Peterson 5710D -6,680 hours -C-27 CAT -Fresh service -New teeth -Undercarriage at 80% -Drag chains and discharge belt still like new PRICE HAS BEEN REDUCED to 437,000 USD !!!!!!! get it while it lasts!!!!!

2003 Peterson HC5400 Grinder -7700 hours -New set of bananas, grates, and teeth -Has a wireless remote -Rotor recently balanced and serviced -New tires ands wheel bearings on axle -Comes with 25K worth of parts MACHINE RUNS AND WORKS BUT NEEDS A FEW MINOR REPAIRS -Has a hole in the metal plate that covers the rotor -Has a small leak in the fuel tank we currently use an auxiliary tank -Intermittent issue of conveyor not feeding. Believe it is a broken wire

Robbins Hurricane Chop Saw 20" blade Live infeed Outfeed with kicker

2005 Rotochopper Cp118 -1600 hours -120 hp engine -Lights and tires -One belt needs a patch(will be repaired)

2018 Salvador SuperCut 100 Automatic Crosscut Saw PRICE REDUCED