Equipment For Sale

EXTREMA DC-203.1 TYPHOON Cyclone & Fabric Filtration Dust Collection System. -- Powerful two-stage dust collection drops out heavier dust particles into a drum before passing finer particles through the fan and filter. -- (1) Fabric filter bag placed above plastic collection bag. -- 1,785 CFM Output. -- 3 HP Induction motor. -- 13" Steel blower fan impellers are dynamically balanced. -- Collection bag snap-in ring for easy addition or removal of plastic bag. -- Filter bag filters dust particles down to (1) Micron in size. -- Low noise operation. -- Includes: Sturdy steel tripod cyclone mounting stand and drum dollies (drum not included.)

EXTREMA DC-2100 TYPHOON Cyclone & Fabric Filtration Dust Collection System.Powerful two-stage dust collection drops out heavier dust particles into a drum before passing finer particles through the fan and filter.Specifications: -- (2) Fabric filter bags placed above plastic collection bags with 117 Sq. Ft. total cloth area -- 32 Cu. Ft. of storage capacity -- Rated at 6,400 CFM at 16" static pressure output. -- 10 HP Induction Motor. -- Inlet 13" with 16" Steel blower fan impeller that is dynamically balanced.Features: -- Collection bag snap-in ring for easy addition or removal of plastic bag. -- Filter bags filter out dust particles down to (1) Micron in size. -- Low noise operation. Includes: -- Sturdy steel tripod cyclone mounting stand and drum dollie (drums not included).

EXTREMA RC-04 Rotary Air Lock Standard capacity Rotary Air Lock; Cycles waste off of a cyclone dust collector while maintaining internal pressure.Specifications: -- The Rotary Air Lock is an essential device for dust collectors that dump directly into a dumpster or hopper. -- This unit has a 16" dia. lock with a 1/2 HP motor. -- 33 RPM TEFC Direct drive motor. -- 16" Inlet dia. & 16" outlet diameter. -- (8) Rubber blades. -- Does not include electrical controls. -- Features: Approx. 10 Cu. Ft./Min capacity.

EZ CAR CRUSHER MODEL A+ --Opening 20 ft long x 7'6" width x 8 ft height --System Pressure 2500 psi --Port Reliefs Set At 2650 psi --Cylinders 10" bore --Travel 78" --Shaft 4" rod --Remote --Approx 5,500 Hours

MODEL A EZ CAR CRUSHERHydraulicsSystem Pressure 2500 psiPort Reliefs Set At 2650 psiCylinders 10" boreTravel 78"Shaft 4" rodOpeningSize 20" x 8'1" x 7'7"OverallWeight 61,000 lbsLength 43'3"Travel & Operating Height 13'3"

EZ CAR CRUSHER MODEL B With Remote --HydraulicsSystem Pressure 2500 psiPort Reliefs Set At 2650 psi --Cylinders 8" bore --Travel 72" --Shaft 2.5" rod --OpeningSize 20" x 7'6" x 7'7" --OverallWeight 49,000 lbsLength 43'5"Travel & Operating Height 13'3"

EZ SANDER EZ-3760 Wide Belt SanderEZ-Sander's are built to with the ability to hold very tight tolerance (+/-.003) side to side when set up properly.Specifications: -- The sanding head is a combination head that consists of a 5" rubber-covered contact drum for the more aggressive sanding and then followed by an adjustable 2-1/2" graphite-covered felt polishing platen for doing very fine finishing sanding using a 37" X 60" abrasive belt. -- The conveyor belt speed is set to run at 10 - 30 FPM and is controlled via AC variable speed unit mounted in the main control panel. Simply adjust the dial setting to your desired feed speed. -- Double infeed and outfeed hold-down rolls are provided to help ensure proper part feeding through the Sander. -- The conveyor table/bed opening has a 0" to 5" opening allowing the operator to sand some parts as thick as 5" and the ability to sand very thin parts as well. -- Power raising and lowering of the conveyor bed is standard. -- Digital thickness display is standard.Complete with & Features: -- EZ Sander is equipped with a state-of-the-art electronic tracking system for the abrasive belt. -- Emergency stop heavy-duty caliper disc brakes bring the sanding head to a stop within 4 to 5 Sec when activated by the machine's safety interlock system. -- Limit Switches on both sides of the abrasive belt to keep the belt from over-travel. NOTE: -- Available in single phase with a 7.5 HP or 10 HP 3-Phase main drive motor. -- Voltage change to 440 Volt ...$275.

Fabtek 546B Early 2000s Approx 24k hours Deere 6068 engine Bogie tires are new Front tires at 20% Pins and bushings are good Was ran through shop about 6k hours ago Valve seals weep a little when its cold Runs and operates good

Fabtech 546c log forwarder -engine been rebuilt -new joysticks -most cylinders have been repacked -brand new center section -hydraulic control valve was rebuilt -new log Bunks brand new LED lights -all new window seals with brand new lexan -new hydraulic hoses -new seat -John Deere power Tech 6 cylinder

1999 FABTEK 546B 8 WHEELED DOUBLE BUNK FORWARDER 6 CYL DEERE POWERSHIFT EXTENDABOOM BYPASS BUCKET JOYSTICKS 700 RUBBER

2006 Fabtek 153 Processor, Equipped with a Fabtek (4) Roller Processor Head, Engine Has 6,100 Hours, was Remaned, Frame Hours 15,800, Enclosed Cab with Heat and Air Conditioning, Undercarriage is 80%, Ready for the Woods. Disclaimer The information is the best of our knowledge at the time of the listing. The price may change without notice and additional charges may apply, including freight, taxes, duties, tariffs, quarantine, etc.

2001 Fabtek FT133, JUST ARRIVED! 22.5” double grouser pads, fixed 4 roller Fabtek processing head, $49,500

Parting Out Fabtek 153 with 4 Roller Head, Lots of Good Parts

2001 FABTEK 133 TRACKED HARVESTER 6 CYL DEERE FABTEK FOUR ROLLER HEAD

THESE ARE BRAND NEW FABRICATED BUNKS FOR FABTEK FORWARDERS 2000 DOLLARS EACH

THESE ARE BRAND NEW FABRICATED STAKES FOR FABTEK FORWARDER THESE ARE 2300 EACH

1998 FABTEK 344B SINGLE BUNK FORWARDER 4 CYL DEERE POWERSHIFT JOYSTICK CONTROLS BYPASS BUCKET ROTATER 23.1-26 RUBBER

2004 Fabtek 344B Single Bunk Forwarder, Engine has 14,400 Hours,3 New Tires, Center Section is 75%, Newer Bucket and Window, Newer Set of DD Chains, Enclosed Cab with Heat and Air Conditioning, Ready for the Woods. Disclaimer The information is the best of our knowledge at the time of the listing. The price may change without notice and additional charges may apply, including freight, taxes, duties, tariffs, quarantine, etc.

2011 FAE, BBS250 Mulcher, FAE Soil Mill, Has Less Then 500 Hours, Weighs 12,604 Pounds,This Guy owns Two and he is just down sizing, Roller is currently off for their needs but can easily be reinstalled. Please Call For More Info.

2023 FAE PT175 Forestry Mulcher, 900 Hours. Runs Excellent. Call Today for Sales or Rental.