Equipment For Sale

SAMUEL TANK-660V-150PSI 660 Gallon Air Receiver660 Gallon Vertical Air Receiver Tank. • Diameter O.D./I.D.: 42 O.D. • MAWP: 150 PSI @ 400° F • MDMT: -20°F @ 150 PSI • Capacity: 660 Gallons • Pressure: 150Support & Attachments: • 8 Base Ring • Safety Valve & Pressure Gauge - 700/MCTK-SW10-150Recommended Option: Zero Loss Compressed Air Condensate Trap w/WindowPowers through Condensate buildup and Ideal for Compressor applications up to 100 HP (500 SCFM).Ideal for inline filters up to 5000 SCFM. • The WaterHog™ design avoids small passages common on competitor designs, ensuring clog-free operation. • Fully Automatic Operations. No timer or manual settings • No Electrical Connections. WaterHog™ is powered by compressed air, avoiding the need for electrical wiring and connections. • Energy Saving Operation. Zero compressed air loss when properly installed with balance line. • Check with your utility to see if it qualifies for energy efficiency incentives. • WaterHog™ pays for itself when replacing open condensate drain valves or timer traps. • Low Profile. • The 4.7" vertical operating height allows WaterHog™ to fit where other larger units can't. • Max Operating Pressure: 200 psig • Min/Max Control Pressure: 40/130 psig • Min/Max Temperature: 34/170 F • Inlet / Outlet Connections: 1/2 inchPrice ...$ 450.00 (2) Year Warranty Included

Samuel Rogers 66" Knife Grinder

KENT - Single Head, ResawSpecifications: -- 15 HP Motor. -- Blade size: 168"; x 1"; x 0.035"; 2TPI. -- 6" Wide feed belt. -- Operational working heights: 1/4" minimum cut to 8"; maximum. -- Feed speed: 20 - 150 Feet per minute.

1984 Sanborn Min Max Wide Band Sawmill with Live Deck. Detroit 271 engine with the largest injectors that are made for that engine. It starts and runs well. Includes: hydraulic drive 3 chain live deck that is about 16' long and 12' wide with a stop and loader and arms that go across the bed of the mill. The logs must be rolled across the arms to the 4 head blocks. The frame of the live deck is mounted on 3x3x3 concrete cubes. set of 4 large head blocks with the same design as the original but which are about 12" large capacity than the originals. 40 foot long 3 chain green chain with new hydraulic motor and large gear reduction unit, 3 saw Chase 24+" edger with a 271 power unit that starts and runs well. 7 bands here and another 5 being repaired. Maintenance and Repairs Done: - balanced both wheels, reground both wheels - removed some weight from the upper wheel - added a weight strain system instead of a small spring - added vibration damping connections - provided electric shut off and throttle to the engine - added an auxiliary open center hydraulic pump and valves. The pump is driven off the front of the crankshaft of the engine - replaced the bearings throughout the mill - strengthened the take away table to take very heavy loads - installed a new set work screw system - removed the pantograph for hydraulic supply and replaced it with an igus hose and cable carrying chain Call 800-459-2148 for more info.

2000 Sanborn Min Max This is not a whole mill. - Two complete good working Silvatech Set works , - Four Heavy Duty Head Blocks . Board Dogs, Cant Dogs, Turners and Tapers all Hydraulic. These were custom built super heavy duty for this mill . Very well cared for. Great care taken in the removal. - Every thing is under cover. - It’s the complete system with everything you need to put it back together, all labeled and photos. - The spare set works was near new when bought. - Everything is on heavy duty pallets can be shipped. Call 800-459-2148 for more info.

This mill has been damaged, but if you want good parts there are some here. Call 276-472-2199 for more info.

Like new 36" vertical linebar resaw. COMPLETE WITH RUN AROUND SYSTEM. Saws 14"W x 16"H x 12'L cants (can be extended). Operator's cab w/ controls. Elec. sys. w/ starters, prewired mach. Pre-plumbed hyd. sys. 20HP hpu, sub-steel, ten saws incl. Mach. disassembled. Crane additional. $90,000. OBO

Sanborn Machinery RH 8 Saw Drop Saw Trimmer with Hydraulic Drive

Sanborn 5' Band Head Rig Air Strain w/ 100HP Electric Motor

Sanborn 6' Left Hand Double Cut Band Head Rig on 17 Degree tilt

SAND-RITE DB-612 DLX Sander with Heavy Duty Cast Iron StandCustom ordered to fit your requirements with quick 3 week lead-time!Specifications: -- (1) 6" Diameter x 7" Wide pneumatic drum head , which allows the operator to regulate how firm the sanding head needs to be to conform the head to what they are sanding. -- Motor: 3/4 HP -- (1) B-12 Brush Head, which allows the sanding irregular surfaces with out loss of shape. -- And matching Heavy Duty Cast Iron Stand.

SAND-RITE DUO-DLX Spindle Sander; Horizontal spindle sander with 3/4 HP BALDOR motor. -- Optional brush heads sand irregular surfaces with out loss of shape, and the optional pneumatic drum heads (available in 2" to 8" diameters) allow the operator to regulate how firm the sanding head needs to be to conform the head to what they are sanding. -- Price does not include the stand - Add $308.00 Cast iron stand."Drums, brush heads, and sleeves are additional".Brush Head: ADD $ 175.00 2" X 8" pneumatic drum: ADD $ 140.008" X 9" pneumatic drum: ADD $ 302.00 Special note: 220 grit is the finest grit supplied for Brush Head

SANDINGMASTER - KSB-900, ...Single Head Wide Belt Sander36" Width cap.; combination sanding head.Head: Rubber covered spiral grooved contact roll & finishing platen.Specifications:15 HP Main motor.37" x 75" Abrasive belt size.Electronic tracking and air tensioning of abrasive belt.Rubber covered infeed & outfeed holddown rollers & holddown shoes.Variable feed speed 15 - 45 FPM via 1.5 HP motor.0" - 5" Manual part thickness opening.Includes: Optional floating bed for sanding fine veneers.Equipped with & Features:Extended infeed.Load meter.Disc brake on main motor.Safety stop bar.

SANDINGMASTER SA3300-900 TRIPLE HEAD WIDE BELT SANDER3-Head, 36" max. width cap. - 1st Head: 11" Dia. rubber covered contact roll, 24 HP motor; 2nd Head: 11" Dia. rubber covered contact roll, 18 HP motor; 3rd Head: Combination head with rubber covered contact roll and finishing platen, 18 HP motor. 37" x 75" Abrasive belts with electronic tracking. -- 2-Speed conveyor feed, 23 & 46 FPM, 1.0/1.7 HP motor, 0" - 6" motorized part thickness with LED readout, a joystick lever controls raise and lower of feed bed and start and stop of conveyor belt, also includes "SP-Matic" automatic part thickness setup. -- Thin veneer sanding package with rigid table setting for solid wood dimensioning and floating table setting for veneer sanding, infeed and outfeed spring loaded holddown shoes. -- Includes: Motor load meters, electronic brakes on sanding heads, infeed safety shutoff bar and 18" infeed conveyor area. Actual model "SA-3300-900".

SANDMAN DL7236 Downdraft Sanding Table;The SANDMAN Sanding Table is a dedicated sanding station that doubles as a workbench.Specifications: -- 72" X 36" Rubberized work surface. -- 1.5 HP T.E.F.C. 220V 1-Phase motor with 10-5/8" LAU blower with sealed ball bearings. -- Industrial casters with 4" wheels, (2) ridged, (2) swivel-lock 2-ways. -- Magnetic tool holder. -- Hinged tilt-up top with gas strut lid support for easy filter servicing. -- Adjustable in height from 34" - 38". -- Grid system top adds versatility. -- 10.4 Cu. Ft. of built in storage area with 1 pull out shelf. -- Easy filter service.

SANDMAN M74836 Downdraft Sanding TableGreat sanding table for a singular function such as doing cabinet doors, door fronts, etc. This downdraft table has a 6″ overhang on the front side making it good for sanding while sitting. Machine comes standard with casters, utility tray, & Felt-lined Platforms.Specifications: 48 L x 36" W top surface with heights of 32", 34" $ 36". -- Overhangs of 6" front. 0" back and 4" ends. -- (2) DP20252 Filters and (1) PF4029 pre-filter. -- 1 HP Baldor Motor – Standard Single Phase 110V (13 Amps) -- (18) Month warranty on parts.(Single and 3-Ph 220V available)NOT IN STOCK - CALL OR EMAIL FOR CURRENT LEAD TIME TO SHIP. PRICING SUBJECT TO CONFIRMATION.

SANDMAN DL7236 Downdraft Sanding Table;The SANDMAN Sanding Table is a dedicated sanding station that doubles as a workbench. -- 72" X 36" Rubberized work surface. -- 1.5 HP T.E.F.C. 220V 1-Phase motor with 10-5/8" LAU blower with sealed ball bearings. -- Industrial casters with 4" wheels, (2) ridged, (2) swivel-lock 2-ways. -- Hinged tilt-up top with gas strut lid support for easy filter servicing. -- Adjustable in height from 34" - 38". -- Grid system top adds versatility. -- 10.4 Cu. Ft. of built in storage area with 1 pull out shelf. -- 18 Months Limited WarrantyNOT IN STOCK - CALL OR EMAIL FOR CURRENT LEAD TIME TO SHIP. PRICING SUBJECT TO CONFIRMATION.

SANDMAN M7236 Downdraft Sanding Table110V 1 HP (M7236) T.E.F.C Motor with 15’ power cord. -- 72" x 36" Rubberized work surface. -- 10-5/8" LAU blower with sealed ball bearings. -- Industrial casters with 5" wheels, (2) ridged and (2) swivel-lock 2-ways. -- Hinged tilt-up top with gas strut lid support for easy filter servicing. -- Grid system top adds versatility. -- (18) Month warranty on parts.NOT IN STOCK - CALL OR EMAIL FOR CURRENT LEAD TIME TO SHIP. PRICING SUBJECT TO CONFIRMATION.

SANDMAN DL9648 Downdraft Sanding TableThe DL9648 is a dedicated 96" x 48" sanding table that doubles as a workbench. The Sand Pro DL9648 is perfect for sanding large pieces such as doors or as a multi-person sanding station. Specifications: -- Table height 36", table size 96" x 48". -- (2) 1.5 HP TEFC motors with 7,400 CFM @ 1.5 SP and (2) 16" backward inclined fans. -- (6) Extended surface pleated filters each 20" x 25" x 2" deep w/ 1/2" netted polyester filter. Features: -- (4) 110 V duplex receptacles. -- Rubberized mar-proof top. -- Grid system top for jigs and fixtures. -- Hinged top with gas strut lid support for easy access to filters. -- (2) 10" x 32" Shelves. (2) 18" x 24" Storage drawers. -- Stainless steel hanger for air orbital sanders (choose 5" or 6"). Options: -- 3" Swivel casters (Adds 3/4" to machine height). -- Case of (12) replacement filters. -- Single phase available -- 18 Month Limited WarrantyNOT IN STOCK - CALL OR EMAIL FOR CURRENT LEAD TIME TO SHIP. PRICING SUBJECT TO CONFIRMATION.

SANDMAN M74831 Downdraft Sanding TableGreat sanding table for a singular function such as doing cabinet doors, door fronts, etc. This downdraft table has a 6″ overhang on the front side making it good for sanding while sitting. Machine comes standard with casters, utility tray, & Felt-lined Platforms.Specifications: 48 L x 31" W top surface with heights of 32", 34" & 36". -- Overhangs of 6" front. 0" back and 4" ends. -- (2) DP20252 Filters and (1) PF4029 pre-filter. -- 3/4 HP Baldor Motor – Standard Single Phase 115V (11.4 Amps) -- New filters and pre-filters installed.