Select For Sale

52 inch opening, 2762 lbs, 360 rotation

#134 • Caterpillar Forklift -- Specifications -- Year: unknown. Make: Caterpillar. Model: GC45K-SWR. Serial #: AT87A00367. Engine: unknown 4.3 liter. Fuel: LP. Load Capacity: 10,000 lbs. Mast Height: 98”. Meter Reads: 12,160. Reach Height: 17’. -- Features -- Fork Positioner: no. ROPS: Open. Side Shift: yes. Stage Mast: 3. Tire Size: front22x9x16. rear-13x7x12 1/8. Tires: Solid. -- Seller Statement -- Sells with extra set of 6’ forks, no propane tank

CATERPILLAR CB LINKAGE BRACKET INSTALLED PART NUMBER 253-7830 CATERPILLAR GSH324 WH GRAPPLE CATERPILLAR PART NUMBER 587-8986 INCLUDES CONNECTING LINES INCLUDES MOUNTING PINS INCLUDES WASTE HANDLING SHELLS SOLD AS IS

CAT G126 Contractors Grapple FOR USE WITH: "CB" Linkage FOR USE WITH: PIN ON OR PIN GRABBER COUPLER Online Owner's Manual

1.3YD FRONT LOADER BUCKET FOR USE WITH: 420F/F2, 430F/F2 ST, NEXT GEN 420, 420XE, 430 PIN ON

CAPACITY:UP TO 1000 TONS PER HOUR CASTING:75 FEET CUTTING HEIGHT UP TO 55 INCHES DRIVE: RUNS OFF CARRIER VEHICLE HYDRAULICS, 3700 PSI @ 50 GPM FLAT CAST: RIGHT, 135-DEGREE ROTATION TO THE LEFT FUSION INTERFACE Online Owner's Manual SIZE: 36” DIAMETER; 12” DEEP MINIMUM FAN WIDTH: 108” OR 120”

89" WIDTH BOLT ON CUTTING EDGE CATERPILLAR 1.3 CUBIC YARD MULTI PURPOSE BUCKET CATERPILLAR PART NUMBER 232-2696 FOR ALL BACKHOE MODELS EXCEOT 446 AND 450 IT LINKAGE SOLD AS IS

CATERPILLAR H55S HAMMER CATERPILLAR PART NUMBER 561-2551 HAS NOT BEEN USED INCLUDES 1 CONE TOOL AND 1 CHISEL TOOL INCLUDES 303/304 BRACKET INCLUDES CONNECTING LINES SOLD AS IS

2950 FT/LBS AUTOLUBE CHISEL BIT INSTALLED HAMMER M318F PIN LOCK BRACKET INSTALLED NEW GET NITROGEN GAS FIRED HAMMER SOLD AS IS

6000 ft/lbs impact force AUTOLUBE INCLUDES CATERPILLAR CB LINKAGE BRACKET INCLUDES PINS MOIL POINT NEW GET SOLD AS IS

CAT H160ES HAMMER COMMENTS: HAS AUTOLUBE. CONNECTING LINES INSTALLED DB BRACKET WITH PINS Online Owner's Manual REBUILT BY MILTON CAT

CATERPILLAR H160S HAMMER CATERPILLAR PART NUMBER 590-1662 HAMMER INCLUDES TB BRACKET INCLUDES AUTOLUBE INCLUDES BUCKET PINS INCLUDES CHISEL TOOL SOLD AS IS

AUTOLUBE INSTALLED CATERPILLAR H160S HAMMER CATERPILLAR PART NUMBER 590-1662 DB LINKAGE BRACKET INSTALLED INCLUDES CONNECTING LINES AND MOIL TOOL SOLD AS IS

CATERPILLAR H180S HAMMER CATERPILLAR PART NUMBER 590-1661 INCLUDES CHISEL TOOL INCLUDES CONNECTING LINES SOLD AS IS TB LINKAGE BRACKET INSTALLED

1998 Caterpillar 525B Grapple Skidder, No Winch, 12,700 Hours, Tires are 30.5 x 32, Good Tread, New Hydraulic Pump, Axle has New Bearings, Center Section is Tight, Front Axle Bearing Replaced, Two Seals in Cylinder Replaced, New Bearings in Cradle, Ready for the Woods. Operating Weight 35,800 lb Overall Length 21.29ft in Overall Width 11.11ft in Height To Top Of Cab 10.61ft in Disclaimer The information is the best of our knowledge at the time of the listing. The price may change without notice and additional charges may apply, including freight, taxes, duties, tariffs, quarantine, etc.

Grapple And Winch Skidder Single Arch Attachments Blade- Yes Exterior- ROPS- Enclosed Interior A/C- Yes Heater- Yes Engine

2007 Caterpillar 525C Grapple Skidder C7 engine Dual arch Winch 13500 hours 30.5 tires Will need two batteries

2014 Caterpillar 525C Dual arch Winch Good rubber Center section good 12k hours Woods ready

2014 Caterpillar 525C Skidder Cab Heat AC Dual Arch Winch New Fuel Pump New Injectors 10K hours