Equipment For Sale
10585 Results Found
Call for Price
EZ CAR CRUSHER MODEL B With Remote --HydraulicsSystem Pressure 2500 psiPort Reliefs Set At 2650 psi --Cylinders 8" bore --Travel 72" --Shaft 2.5" rod --OpeningSize 20" x 7'6" x 7'7" --OverallWeight 49,000 lbsLength 43'5"Travel & Operating Height 13'3"
Call for Price
EZ CAR CRUSHER MODEL A+ --Opening 20 ft long x 7'6" width x 8 ft height --System Pressure 2500 psi --Port Reliefs Set At 2650 psi --Cylinders 10" bore --Travel 78" --Shaft 4" rod --Remote --Approx 5,500 Hours
$ 14,995
EZ SANDER EZ-3760 Wide Belt SanderEZ-Sander's are built to with the ability to hold very tight tolerance (+/-.003) side to side when set up properly.Specifications: -- The sanding head is a combination head that consists of a 5" rubber-covered contact drum for the more aggressive sanding and then followed by an adjustable 2-1/2" graphite-covered felt polishing platen for doing very fine finishing sanding using a 37" X 60" abrasive belt. -- The conveyor belt speed is set to run at 10 - 30 FPM and is controlled via AC variable speed unit mounted in the main control panel. Simply adjust the dial setting to your desired feed speed. -- Double infeed and outfeed hold-down rolls are provided to help ensure proper part feeding through the Sander. -- The conveyor table/bed opening has a 0" to 5" opening allowing the operator to sand some parts as thick as 5" and the ability to sand very thin parts as well. -- Power raising and lowering of the conveyor bed is standard. -- Digital thickness display is standard.Complete with & Features: -- EZ Sander is equipped with a state-of-the-art electronic tracking system for the abrasive belt. -- Emergency stop heavy-duty caliper disc brakes bring the sanding head to a stop within 4 to 5 Sec when activated by the machine's safety interlock system. -- Limit Switches on both sides of the abrasive belt to keep the belt from over-travel. NOTE: -- Available in single phase with a 7.5 HP or 10 HP 3-Phase main drive motor. -- Voltage change to 440 Volt ...$275.
$ 69,000
1998 FABTEK 344B SINGLE BUNK FORWARDER 4 CYL DEERE POWERSHIFT JOYSTICK CONTROLS BYPASS BUCKET ROTATER 23.1-26 RUBBER
2006 Fabtek 153 Processor, Equipped with a Fabtek (4) Roller Processor Head, Engine Has 6,100 Hours, was Remaned, Frame Hours 15,800, Enclosed Cab with Heat and Air Conditioning, Undercarriage is 80%, Ready for the Woods. Disclaimer The information is the best of our knowledge at the time of the listing. The price may change without notice and additional charges may apply, including freight, taxes, duties, tariffs, quarantine, etc.
$ 71,900
2004 Fabtek 344B Single Bunk Forwarder, Engine has 14,400 Hours,3 New Tires, Center Section is 75%, Newer Bucket and Window, Newer Set of DD Chains, Enclosed Cab with Heat and Air Conditioning, Ready for the Woods. Disclaimer The information is the best of our knowledge at the time of the listing. The price may change without notice and additional charges may apply, including freight, taxes, duties, tariffs, quarantine, etc.
2001 Fabtek FT133, JUST ARRIVED! 22.5” double grouser pads, fixed 4 roller Fabtek processing head, $49,500
$ 71,900
2004 Fabtek 344B Single Bunk Forwarder, Engine has 14,400 Hours,3 New Tires, Center Section is 75%, Newer Bucket and Window, Newer Set of DD Chains, Enclosed Cab with Heat and Air Conditioning, Ready for the Woods. Disclaimer The information is the best of our knowledge at the time of the listing. The price may change without notice and additional charges may apply, including freight, taxes, duties, tariffs, quarantine, etc
$ 105,000
Fabtech 546c log forwarder -engine been rebuilt -new joysticks -most cylinders have been repacked -brand new center section -hydraulic control valve was rebuilt -new log Bunks brand new LED lights -all new window seals with brand new lexan -new hydraulic hoses -new seat -John Deere power Tech 6 cylinder
$ 55,900
Fabtek 546B Early 2000s Approx 24k hours Deere 6068 engine Bogie tires are new Front tires at 20% Pins and bushings are good Was ran through shop about 6k hours ago Valve seals weep a little when its cold Runs and operates good
$ 85,000
Fabtek 546C 6WD Forwarder, Clean Machine Inside and Out, New Grapple. Front Chains, Deere Motor. Call Today.
$ 74,900
1999 FABTEK 546B 8 WHEELED DOUBLE BUNK FORWARDER 6 CYL DEERE POWERSHIFT EXTENDABOOM BYPASS BUCKET JOYSTICKS 700 RUBBER
Call for Price
$ 2,000
$ 2,300
$ 299,000
2023 FAE PT175 Forestry Mulcher, 900 Hours. Runs Excellent. Call Today for Sales or Rental.
$ 154,900
2014 FAE P-175 Forestry Mulcher, Cummins 4,5L Cummins Engine, 165 HP, 870 HOURS on Rebuilt Engine, 1800 Frame Hours, Denis Cimaf 180D Mulcher Head, Has New Liner, New Runners Balanced, New Bearings New Undercarriage, Heat and AC, Purchased for a job and it fell through, Ready for the Woods. Length 253" Height 104" Width 69" Weight 24,145 Disclaimer The information is the best of our knowledge at the time of the listing. The price may change without notice and additional charges may apply, including freight, taxes, duties, tariffs, quarantine, etc.
Call for Price
2007 FAE PT400 with 6762 Hours and a 300U/250 mulching attachment with 400 Hours! Weight 7,033 lbs Length 291 in Width 108" Height 123" Disclaimer The information is the best of our knowledge at the time of the listing. The price may change without notice and additional charges may apply, including freight, taxes, duties, tariffs, quarantine, etc.