Equipment For Sale

EXTREMA DC-3200S TYPHOON Fabric Filtration Modular Dust Collection System. With 1-micron dust filtration efficiency this collector will make your shop cleaner, healthier, and more productive.Specifications: -- (5) Fabric filter top bags are mounted above individual plastic collection bags. -- The multi-bag system is placed on sturdy steel legs in a horizontal series. -- 8,975 CFM Output with single-stage blower. -- Additional filtration sections can be easily added. -- Heavy Duty 20 HP induction motor, 16" inlet. -- 25" Steel blower fan impellers are dynamically balanced. -- Collection bag snap-in rings for easy addition or removal of plastic bags. -- 1-Micron filter bags with 6 mil plastic bottom collection bags are standard. -- Wye-Delta soft start power switch. -- Options: Remote control, drum storage kit.

EXTREMA DCF-04 Bag Filter. -- Features a 14" inlet; unit has (4) sections, (4) 1 micron filter bags with (4) plastic collection bags, rings, clamps and legs. -- Modular design enables additional sections to be added or removed. -- Excellent addition to the "DCY Typhoon" Dust Collector!

EXTREMA DCY-750.3 TYPHOON Cyclone Dust CollectorCyclone & fabric filtration dust collection system. -- Powerful two-stage dust collection drops out heavier dust particles through a 1/2 HP Rotary Air Lock (included), allowing you to choose the disposal system, before passing finer particals through the fan and filter. -- (2) Fabric filter bags placed above plastic collection bags. -- Air volume output rated @ 4,850 CFM with 7.5 HP Induction motor with 12" inlet. -- 14-3/4" Steel blower fan impeller and is dynamically balanced. -- Collection bag snap-in ring for easy addition or removal of plastic bag. -- Filter bags filter dust particles down to (1) Micron in size. -- Low noise operation. -- Includes: Standard support frame to allow use with a waste hopper under the cyclone.

EZ SANDER EZ-3760 Wide Belt SanderEZ-Sander's are built to with the ability to hold very tight tolerance (+/-.003) side to side when set up properly.Specifications: -- The sanding head is a combination head that consists of a 5" rubber-covered contact drum for the more aggressive sanding and then followed by an adjustable 2-1/2" graphite-covered felt polishing platen for doing very fine finishing sanding using a 37" X 60" abrasive belt. -- The conveyor belt speed is set to run at 10 - 30 FPM and is controlled via AC variable speed unit mounted in the main control panel. Simply adjust the dial setting to your desired feed speed. -- Double infeed and outfeed hold-down rolls are provided to help ensure proper part feeding through the Sander. -- The conveyor table/bed opening has a 0" to 5" opening allowing the operator to sand some parts as thick as 5" and the ability to sand very thin parts as well. -- Power raising and lowering of the conveyor bed is standard. -- Digital thickness display is standard.Complete with & Features: -- EZ Sander is equipped with a state-of-the-art electronic tracking system for the abrasive belt. -- Emergency stop heavy-duty caliper disc brakes bring the sanding head to a stop within 4 to 5 Sec when activated by the machine's safety interlock system. -- Limit Switches on both sides of the abrasive belt to keep the belt from over-travel. NOTE: -- Available in single phase with a 7.5 HP or 10 HP 3-Phase main drive motor. -- Voltage change to 440 Volt ...$275.

2000 FABTEK 346B DOUBLE BUNK FORWARDER 4 CYL DEERE POWERSHIFT JOYSTICK CONTROLS SQUUIRT BOOM

2001 Fabtek FT133, both Knife Cylinders repacked, roller cylinder repacked , main lift cylinder repacked, double grouser style 22.5 " pads, fixed 4 roller Fabtek Processing head, nice machine for the year, and has been well taken care of, $49,500

Fabtek 546B Early 2000s Approx 24k hours Deere 6068 engine Bogie tires are new Front tires at 20% Pins and bushings are good Was ran through shop about 6k hours ago Valve seals weep a little when its cold Runs and operates good

THESE ARE BRAND NEW FABRICATED STAKES FOR FABTEK FORWARDER THESE ARE 2300 EACH

Parting Out Fabtek 153 with 4 Roller Head, Lots of Good Parts

THESE ARE BRAND NEW FABRICATED BUNKS FOR FABTEK FORWARDERS 2000 DOLLARS EACH

2006 Fabtek 153 Processor, Equipped with a Fabtek (4) Roller Processor Head, Engine Has 6,100 Hours, was Remaned, Frame Hours 15,800, Enclosed Cab with Heat and Air Conditioning, Undercarriage is 80%, Ready for the Woods. Disclaimer The information is the best of our knowledge at the time of the listing. The price may change without notice and additional charges may apply, including freight, taxes, duties, tariffs, quarantine, etc.

1998 FABTEK 344B SINGLE BUNK FORWARDER 4 CYL DEERE POWERSHIFT JOYSTICK CONTROLS BYPASS BUCKET ROTATER 23.1-26 RUBBER

Fabtek FT153, 14,000 hrs., $59,900

2002 Fabtek FT153 Track Processor 18,247 hours Good U/C Four roller head Good running condition, $49,900

Fabtek four roller processing head in decent condition. Head does come with computer.

Fabtech 546c log forwarder -engine been rebuilt -new joysticks -most cylinders have been repacked -brand new center section -hydraulic control valve was rebuilt -new log Bunks brand new LED lights -all new window seals with brand new lexan -new hydraulic hoses -new seat -John Deere power Tech 6 cylinder

1999 FABTEK 546B 8 WHEELED DOUBLE BUNK FORWARDER 6 CYL DEERE POWERSHIFT EXTENDABOOM BYPASS BUCKET JOYSTICKS 700 RUBBER

2001 Fabtek FT133 Track Processer 18,300 hours Four roller head Runs and works well, $49,900

FAE RCU55 Remote Controlled Tracked Carrier, In Stock. Multiple Head Options Available. Call Today!

2014 FAE P-175 Forestry Mulcher, Cummins 4,5L Cummins Engine, 165 HP, 870 HOURS on Rebuilt Engine, 1800 Frame Hours, Denis Cimaf 180D Mulcher Head, Has New Liner, New Runners Balanced, New Bearings New Undercarriage, Heat and AC, Purchased for a job and it fell through, Ready for the Woods. Length 253" Height 104" Width 69" Weight 24,145 Disclaimer The information is the best of our knowledge at the time of the listing. The price may change without notice and additional charges may apply, including freight, taxes, duties, tariffs, quarantine, etc.