Newman HP-688 Twin Bay Hydraulic Cold Press6-Sections (top platens) each 24" x 30" each, Center posts between third and fourth platens, creating two overall areas of 30" x 74". Specifications: -- Max. fixed opening 48" with 11" cylinder stroke, each platen section has (1) 10" bore with 5" dia. ram cylinder; -- Each platen is 15/16″ thick and it’s back structure is webbed every 5-1/2″ X 7-1/2″. -- Side-mounted self-contained hydraulic system w/tank, 10 HP continuous operating pressure compensating pump. -- Hand-Valves to Cycle Individual Platens with pressure gauges for each platen. -- Idle Pop-Up Bed Rollers in the bottom platen for easy loading and unloading.Over all the press is in excellent condition, is extremely heavily built, and is also a beautiful impressive press in person.

This item is in an Auction on exfactoryauctions.com. Go here to view item: http://exf.ac/i6r NEWMAN S-248 24" x 8" Single-Sided Planer Specifications: Planing thickness 1/16” - 8”. Min. stock length 13”, 4” Butted. Infeed & Outfeed table sizes 24" W x 16-3/4” L. Feed speeds 20 - 100 FPM. Equipped with: 4” Dia. 4-straight knife cutterhead. Segmented serrated upper with 2” W Spring-loaded segments & (3) Solid steel lower feed rollers. Chip breaker, with 2” W Reversible spring-loaded segments.

NICHOLSON Model A2 Ring Debarker:Complete with the following major features and components: -- Fast debarker capable of debarking logs up to 27" diameter. -- Air seal Ring. -- Presently set up as 3-Arm machine which will debark at rates up to about 105 FPM. -- Includes extra parts to make it a 6-Arm machine which could increase production capacity to 212 FPM. -- Mechanical ring centering mechanism.

NICHOLSON Rotomat series 35" Ring Debarker with a 1980s era Ring. -- Frame is 1960s era prior to the "A" series. -- Hydraulic Power Unit. -- Condition is good despite the machine's earlier frame.

NORDFAB NFK Series Modular Dust Collector with (8) Modules, reverse air cleaning and drag chain unloading into a Rotary Air Lock (RAL) --23,000 CFM approx. capacity based on filter area and desired Air to Clothe Ratio. With 50 HP. + 40 HP (was used as a transfer blower) Consisting of (248) filter bags of 8.7" dia. x 77.2 " long(220 mm x 1,960 mm long) also (8) filter bags of 8.7" dia. x 54.1" long.(220 mm x 1,375 mm long) - located at cleaning fans - for a total of 3,680 sq. ft. of filter area. -- Consists (8) modules and (1) inlet blank module. Fan inlet approx 26" dia. -- Bottom conveyor chain with scrapers carrying the dust to one end and fed into the RAL -- Includes NRS-10 Rotary Air Lock and Transfer Blower to convey the dust to an enclosed waste container (not included). -- Electrical control panel with starters included. -- Overall dimensions 32' long x 7.5' depth x 13.5' high (without support steel)., Approx weight 10,000 lbs. --Actual model is NFK 8AJ/1BL

NORFIELD - 250-M: Strike Router -- Strike Router capacity: 9' Length x 1-5/8" thickness cap.; infinite width; mortising plate & bolt relief in: (1) Continuous operation. -- 1-1/2 HP Router: Processes any strike up to 4-7/8" long, including T-strike. -- Rectangular relief leaves more wood in jamb for greater strength and more professional appearance.

NORTH AMERICAN PL-30 ROTARY PHASE CONVERTERPro-Line is the Professional Series, digital start, CNC rated, general purpose single phase to three phase rotary phase converter designed to take standard single phase energy and supply full running current to three-phase equipment.Equipped with: -- Control Panel -- NEMA 1 Enclosure (Indoor) -- Built-in Motor Starter -- Digitally Controlled and Protected Start Circuit -- ABB / Baldor Idler Generator Motor -- ODP (Open Drip Proof) – Indoor Rated -- Soft Start -- 10-Year Parts / Lifetime Labor Warranty

This item is in an Auction on exfactoryauctions.com. Go here to view item: http://exf.ac/i6q NORTHFIELD 12HD 12" Heavy-Duty Jointer Specifications: Max. depth of cut 5/8", Rabbeting cap. 5/8" x 12". 17” x 51-1/2” x 32-1/2” H. Outfeed table size 17” x 43” x 32-1/2” H. Equipped with: 3-1/2” Dia. 3-Knife Cutterhead. 5 HP - 1,735 RPM Motor. 52” L x 5-1/2” H Cast-iron fence, with 0° - 45° Tilt. Swing-away guard.

NORTHFIELD - #4, ...Table SawSpecifications: -- 16" Dia. saw blade cap.; 7.5 HP - 3,450 RPM motor; 1" dia. arbor; 13/16" dado cap. with: Thin collar; blade tilts: 0° - 45°; 32" rip cap. with T-type fence.

NORTHTECH - NT-SL2000XL, ...Straight Line Rip SawSpecifications: -- 20 HP Direct Drive Straight Line Rip Saw. -- 2" Arbor. -- Distance from column to blade: 18 in. -- Saw blade size: 10" - 14". -- 3-1/8" Cutting capacity. -- Glue Line Saw. -- Feed Motor: 1.5 HP. -- Feed Speed: 20 - 105 FPM.

Northtech FR-200 Frame SawSpecifications: -- Saw capacity of 6" width x 8" vertical capacity. -- Minimum working 2"; high X 12"; long. -- Main drive motor to saw frame is 30HP 3PH, wired 460 --V servo drive system to feed works is 1/4HP 3PH, --Blower to saw frame rack for added cleaning value is 3HP 3PH, -- Body of frame saw is (2) sections allowing for fast access to the saw frame, -- Saw blade speed is fixed at 550RPM, -- Dust extraction requires min 3000 CFM and is arranged with (4) 5" ports, -- Blade size is standard with 500mm L x 40mm W x 0.9mm body in stellite or TCT tip,Equipped with & Features -- Digital electronic oiling system provides proper lubrication to the saw frame guides -- Vertical rail system which allows optimum cooling and long term durability, -- (4) guide blocks are thermo- censored to allow auto shut-off of machine should possible heat buildup occur.Machine dimensions 122"; L X 40"; WX, 79"; H weight 7100 lbs. Machine was new in 2007.

NORTHTECH - SRS-12: Straight Line Rip-SawSpecifications --15 HP Motor; 1" dia. saw arbor; speed of 4,500 RPM, 8". -- Max. blade cap.: 12". -- Max. depth of cut: 3-5/16". -- Part length: 8" Min. -- Distance between saw & column: 18"; 60" W x 33" table. -- Feed & Chain: 2 HP Feed drive motor; variable feed speeds of: 59 - 72 - 91 - 111 & 137 FPM. -- 7" Wide double chain; with automatic chain lubrication.Equipped with & Feature: -- Top pressure system with: (6) Spring loaded holddown rollers. -- Double row antikickback fingers. -- Adjustable infeed fence. -- Safety side guard. -- 4" Dia. dust hood outlet. -- Push-button controls. -- Magnetic starters. - Overhead post for laser mounting.

NORTHTECH NT-KL-43-RC Wide Belt Sander (2) Heads;43" width cap. Drum, Combination Head.Head Configuration:1st Head: Rubber-covered contact drum with 25 HP motor2nd Head: Combination head with a rubber-covered contact drum and 2-1/4" wide finishing platen, 20 HP motor.Specifications: -- Thickness opening with PLC control, (DP-525 controller) keypad entry automatically adjusts to any thickness with LED readout. -- 37" x 75" Abrasive belts, TRU-TRAK solid state abrasive belt tracking. -- Variable feed drive 13 - 49 FPM, 2 HP motor. -- Endless belt conveyor, infeed and outfeed rubber covered pinch rolls. -- Complete with: 0" - 6" Automatic part thickness set up.Equipped with & Features: -- Infeed and outfeed rubber covered spring loaded holddown rolls. -- Feed emergency stops at infeed. -- Disc brakes on sanding heads, electrical interlocks on main access doors, and motor load meters. -- Note: Year of manufacturing has to be verified.

NORTHTECH NT-EV-920RC Dual Head Wide Belt Sander2-Head Wide Belt Sanding Machine with 37" capacity. Specifications: -- First head 8-1/4" Dia. grooved rubber contact roll, with 20 HP motor. -- Second head: Combination finishing platen with grooved rubber roller and polishing pad, with 15 HP motor. -- Two (2) infeed and outfeed spring loaded holddown rollers; 2 HP variable speed feed drive. -- Sanding belt size: 37" X 85" and with electronic belt tracking. -- Motorized opening between conveyor bed and sanding heads. -- Ammeters for measuring motor loads. -- Includes spare abrasive belts.

NORTHTECH - NT-920C-200: 2-Head Planer Sander Specifications -- 2-Head. 37" width cap.; 1-knife planer head followed by a wide belt sander head. -- 0" - 6" Motorized opening with: PLC control; keypad entry; LED readout for part thickness. -- 1st Head. 6" Dia. helical planer head with: (6) Rows of staggered carbide inserts; each insert has (4) usable sides; 30 HP motor. -- 2nd Head. Combination sanding head with: 4-5/8" Dia. rubber covered contact roll; 2-1/2" wide finishing platen; 20 HP motor. -- 37" x 75" Abrasive sanding belt; solid-state belt tracking. -- 3 HP Variable feed drive from 15 - 50 FPM; endless belt conveyor with automatic tracking.Complete with: -- Infeed over thickness bar. -- Emergency stops at infeed & outfeed. -- Air-operated disc brakes on sanding heads. -- Electrical interlocks on main access doors. -- Electrical controls with overload protection. -- Motor load meters. -- Panel cleaning brush.

NORTHTECH Four (4) Head Lineal Brush SanderSpecifications: • Sanding Head configuration: 2 Top + 1 Opposing Right + 1 Opposing Left• Working width up to 12"• Working thickness range: 1/4" - 6"• Minimum working length: 30"• (2) Top 1.5 HP Sanding heads RPM are inverter controlled• (2) 1 HP Opposing side sanding heads RPM are inverter-controlled• 150/180 Grit setup included; other grits available upon request• (2) 1/4 HP feed motors with 25 - 105 feed speed range• (2) 5" top dust ports requiring 681 CFM @ point of extraction• (2) 4" Side dust ports requiring 436 CFM @ point of extraction• 230V or 460V 3PH 60HZ• Net / Gross weight: Approx. 1,056 Lbs / Approx. 1,300 Lbs• Approximate Machine dimensions (LxWxH): 59" x 52" x 67"• Tool box and Operation/Parts Manual included• Warranty is one-year parts

//This machine is in an Auction on exfactoryauctions.com// //Link to machine: http://exf.ac/i5z NORTHTECH NT-EV-920RC DUAL HEAD WIDE BELT SANDER 2-Head wide belt sanding machine with 37" capacity. - Heads: 1st head: 8-1/4" Dia. grooved rubber contact roll, with 20 HP motor. 2nd head: Combination finishing platen with grooved rubber roller and polishing pad, with 15 HP motor. Two (2) infeed and outfeed spring loaded hold-down rollers; 2 HP variable speed feed drive. Sanding belt size: 37" X 85" and with electronic belt tracking. Motorized opening between the conveyor and sanding bed. Ammeters for measuring motor loads.

Northtech NT SLR-16SC Precision 16″ Straight Line Rip Saw FEED SYSTEM --Saw motor: 15HP, 3PH 230/460V -- Feed: 1.5HP variable from 40′ – 120′ FPMPRODUCT DIMENSIONS -- Min. thickness: 3/16″ -- Max depth of cut: 4-1/16″ with 16"; Blade -- Max depth of cut: 3-1/16"; with 14"; BladeSpecifications: -- Direct Drive = Direct Drive -- Feed Hp. = 1.5 Hp. -- Feed System = 4"; Split Chain with True Trac -- Feed Speed = 40-120 FPM -- Assisted Start = Wye Delt"; -- Throat Capacity = 18-1/4"; -- Min. Length = 12"; 2nd Roller to Kickback -- Min. Thickness = 3/16″ -- Max. Thickness = 4-1/16"; W/ 16"; BladeGlue Line Rip = Guaranteed 12′ 4/4 stock @ 50 FPMEquipped with & Features -- Blade Size = 14"; Tungsten Carbide Tipped -- Dust Collection = 1417 Total CFM -- Dust Port Out = 4"; Top 6"; Bottom -- Arbor Diameter = 2″ Arbor -- Idle Rollers = (8) Idle Rollers -- Hold Down Style = 8 Spring Loaded Hold Downs -- Kickback Finger = (59) Lower (32) Top -- Automatic Mechanical Oiler -- Low Oil Warning = Low Oil Shut-off -- Laser = 100mw Laser Light & Mount Bracket

NORTHTECH NT-6108ES-6 Edge SanderSpecifications: Sanding Belt is powered by a 3 HP 230/460V motor. -- The platen measures 6-3/4″ X 39″ and has NEW graphite. Rubber covered direct drive pulley. -- Equipped with: (1) 7-3/4" x 37" Adjustable side table and (1) 11-1/2" x 19" Adjustable end table; both side & end tables have vertical table travel w/hand wheel adjustment. Complete with: -- Magnetic controls with overload protection & dust hood with 4" dia. outlet.

NORTHTECH - NT-KL-920-PRK- B & NT-KL-920 PRK-U, ...Top & Bottom 3-Head Planer Sander3-Head bottom with: Planer, drum and platen; 3-head top with: Planer, drum, and platen 920 mm (36") wide.Capacity: 36" x 5" thickness.SpecificationsBottom Machine Model: "NT-KL-920 PPR". -- Infeed driven Conveyor: 37" x 72" Long. -- 1st Head: Spiral cutterhead; (8) rows of 15 x 15 x 2.5 mm inserts carbide knives; (4) sides for rotation; low tool cost.Cutterhead: 175 mm (7") Dia. and 50 HP motor. Segmented chip breaker before the cutterhead. -- 2nd Head: Contact roller; (280 mm) 11" in dia.; 70 durometers, powered by a 40 HP motor; running at 3,600 FPM belt speed.Sanding belt size: 85" x 37". -- 3rd Head: 3-1/4" Pneumatic Polishing Platen; engineered as a combination station, air-cushioned & adjustable in pressure to various grits and materials application. Powered by a 30 HP motor. -- Lifting & lowering conveyor bed; 1-1/2 HP motor (includes auto. thickness setup device). -- Variable speed: 7.5 HP; inverter duty motor integrated with an AC inverter (VFD); control providing variable feed rate from 15 - 70 FPM for heavy calibration; LED readout feed speed indicator. -- Microprocessor Control for: Conveyor bed positioning to high precision via keypad entry. -- Automatic electronic preset panel thickness gauge/micrometer. -- Automatic Air Jet blast cleaning system on both sanding heads.Top Machine Model: NT-KL-920 PRR-U -- 1st Head - Spiral Cutterhead: (8) Rows of 15 x 15 x 2.5 mm inserts carbide knives; (4) sides for rotation; low tool cost.Cutterhead: 7" (175 mm) Dia.; 50 HP motor.Segmented Chip Breaker: Before the cutterhead. -- 2nd Head - Contact Roller: 11" (280 mm) Dia.; 70 durometers; powered by 40 HP motor; running at 3,600 FPM belt speed.Sanding belt size: 85" x 37". -- 3rd Head - 3-1/4" Pneumatic Polishing Platen: Engineered as combination station; air-cushioned & adjustable in pressure to various grits and materials application; powered by 30 HP motor. -- Lifting & lowering Conveyor Bed: Motor 1.5 HP (includes auto. thickness setup device). -- Variable speed 7.5 HP inverter duty motor; integrated with AC inverter (VFD) control; variable feed rate: 15 to 70 FPM for heavy calibration; LED readout feed speed indicator. -- Microprocessor Control: For conveyor bed positioning to high precision via keypad entry. -- Automatic electronic preset panel thickness gauge/micrometer. -- Automatic Air Jet blast cleaning system on both sanding heads. -- Powered dropdown Conveyor between Bottom & Top machine.Features (includes both machines) -- Massive monoblock base: 3/4" Thick plate steel weldments. -- Large dia. roller hold-downs; ball bearing supported; 65 duro UV rubber are standard features. -- Automatic soft start of main motors (Y-Delta). -- Disc braking/emergency shut down protection for: Sanding belt breaking, non-tensioned sanding belt; and mistracking of sand belt. -- All motors & electrics are CE-approved. -- Electronic oscillating belt tracking system. -- Au