#100 • 2007 Baker 3640E Stationary Bandmill Serial #: BBS-O 07-552. Powered by: 40 hp electric. Weight & Height: 26’ x 114”. Hydraulic: Yes. Log Capacity: 36". Cut Capacity: 20'. Extra Wide Head: No. Setworks: Yes. Debarker: No. Bed Extensions: No. Control System: Stationary. Laser Sight: No. Lubrication System: Yes. (for logistics) Weight & Height: 26' x 114". Fully hydraulic, computerized set works, seller states works well, lot includes 10 horse hydraulic pack and motor starters

#200 • 2019 Case 621G Wheel Loader Serial #: JEEN0621KKF246947. Engine: FPT. Fuel Type: Diesel. Meter Reads: 4,011 hours. ROPS: Closed. 3rd Valve: Yes. Center to Center of Pins: 35.5". Lift Capacity: N/A. Tire Size: 20.5R25. Quick Attach: Hydraulic. Attachments: none. A/C: Yes. Heater: Yes. Air ride seat, Bluetooth works, backup camera, low hour good running loader

#202 • HMC RH Carriage Model: AC-40. Serial #: AC40 269 79. # of Headblocks: 4. Carriage Type: Automated. Setworks: Yes. Setworks Make: 110/Air. Scanner: No. Log/Cant Turners: No. Linear Positioning: No. Overall Carriage Length: 15'. Center to Center of Track Wheels: 45". Auto Lube System: No. # of Axles: 5. Wheel size: 10" (First lot of an entirety) Cab with setworks, pantograph arm

#175 • HMC Trim Saw Grading Line Entirety of Lots 169-174 With 10% raise. Contact Eugene with any questions, 574-242-1100

#116 • 2024 Mack Anthem Truck VIN: 1M1AN4GY2RM046976. Engine: Mack MP8. Meter Reads: 98,773 miles. Transmission: Mack M drive 12 speed automatic. GVWR: 52,000 lbs. Front Axle Rating: 12,000 lbs. Rear Axle Rating: 40,000 lbs. Tire Size: 11R22.5. A/C: Yes. Heater: Yes. Wet Kit: Yes. Used, new condition, 1 owner, MP8 505 HP, 3.08 gear ratio, Air ride suspension, 12k front axle weight, 40k rear axle weight, 11R22.5 tires, Aluminum/Steel wheels, 234” wheelbase, Raised roof, 70” sleeper with bed.

#102 • Morgan Dual Head Horizontal Resaw Serial #: S11.00010241S. # of Heads: 2.0. Blade Size: 13’-2”. Blade Tension: Manual. Cut Capacity: 7” x 12”. Drive Type: Line-Shaft. Guide Type: Roller. Overall Dimensions: 162” x 78”. Return: yes. Wheel Size: 24”. Used less than 2 yrs after new, new gearbox for feed belt

#142 • Salem Slant RH Headrig SN:R144560-90. Wheel Size: 13" x 7'. Meat on Wheels: 1 1/2". Strain: Air. Max Throat Opening: 30" x 40". Headrig Set Up: Slant. Features and Notes:Double guide blocks on bottom, band oiler system, 3' x 7' off bear belt, no power, support to ground, Headrig was totally rebuilt when installed in 2010. Contact Eugene with any questions, 574-242-1100

#137 • 2024 Woodpecker 54 x 56 JR Pallet Nailer SN: 239-073124-54X56-JR. Meter Reads: 10,881 pallets. Automatic nailer and stacker. Extra set rails for wing pallets, some extra support parts. Owners manual. Left and right wing flushers, trigger plates. Under 11k pallets made with machine. Excellent condition, owner needs bigger machine. No Reserve!

#204 • 2000 Barko 225 Knuckleboom Serial #: 22817. Engine: 5.9 Cummins. Fuel Type: Diesel. Meter Reads: 3,432 hours. Continuous Grapple: Yes. Trailer: Yes. Delimber: No. Bucksaw Hookups: Yes. A/C: Yes. Heater: Yes. Air conditioner needs work, grapple pins and bushings recently rebuilt, seller states runs and operates as it should

#112 • 2014 Caterpillar 553C Feller Buncher Serial #: CAT0553CTW5300103. Engine: CAT C6.6 Acert. Meter Reads: 6077 hours . ROPS: Closed. A/C: Yes. Heater: Yes. Tire Size: 30.5-32. Tire Chains: No. Type of Head: Forward tilt only. ROPS: Closed. Heat: Yes. Air Conditioner: Yes. Cutter Head Make: Caterpillar. Cutter Head Model: SH56B. Cutter Head SN: A820016. Blade Type: Circle. Cut Capacity: 28". Tilt: Partial. Runs and operates good.

#210 • Cornell Edger Model: 42. Serial #: HE528-11/78. Edger Set Up: Stationary. Cut Capacity: 6" x 42". Infeed Measurement: 46" x 9'6". Outfeed Measurement: 46" x 10'. # of Blades: 2. # of Stationary Blades: 1. # of Moveable Blades: 1. Blade Type: Circle. Arbor Size: 2 7/16". Drive Type: Electric. Lasers: No. Shadow light system, 75 hp electric motor, air cylinder roll lift, manual soft start, wires from box to motor

#110 • Frick 00 Carriage, Husk, and Track Frame Number of Headblocks: 4. Carriage Type: Manual. Scanner: No. Log/Cant Turners: No. Linear Positioning: No. Overall Carriage Length: 14'6". Center to Center of Track Wheels: 38". Auto Lube System: No. Number of Axles: 4. Wheel Size: 8". 44" x 7' Husk, 56" Saw, Belt Drive Carriage Drive, foot pedal recede, drum with cable, 41.5" x 45' Track and Frame

#131 • MDI Metal Detector MDI TWA 2000HD coil with controls. SN: DG10437. Mounted on frame with feed thru trough, 24" x 17' belt, 30" pan, 58" x 52" opening, electric drive, good working condition. Contact Eugene with any questions, 574-242-1100

#106 • Precision Chipper # of Knives: 6. Discharge: Top. Drive Type: Line-Shaft. Working condition, a couple extra set of knives

#180 • 2023 Stringer Wood Chipper SN: 0196. # of Knives: 8. Drive: None. Discharge: Top. Features and Notes: (First lot of an entirety) No pipe, used for only one year. Contact Eugene with any questions, 574-242-1100

#207 • 2016 Tigercat 610E Skidder Serial #: 6101198. Engine: 6.7 Tigercat. Meter Reads: 9,731 hours. Transmission: Hydrostatic. ROPS: Closed. Controls: Joystick. Tire Size: 30.5L-32. Tire Chains: No. Blade Size: 115". Grapple: yes. Cable Winch: Yes. A/C: Yes. Heater: Yes. Dual arch grapple skidder. Heat and air both work, seller states runs and operates well

#135 • 2019 Wood-Mizer LT70 Hydraulic Bandmill Model: LT70 Wide Super Hydraulic. Serial #: 456D72418KNJA5233. A55. 11. Meter Reads: 10,557 hours. Powered By: 55 hp Yanmar. Hydraulic: Yes. Log Capacity: 20'. Cut Capacity: 30". Extra Wide Head: Yes. Setworks: Yes. Debarker: Yes. Bed Extensions: No. Control System: Portable Pedestal. Laser Sight: Yes. Lubrication System: Yes. Weight & Height: 6,000 lbs. 25’ x 7’ x 8’ high. Less than 4,000 hrs on new engine. Fully hydraulic. All oils and filters serviced every 500 hrs, (Schaeffer’s oil), will have axle and wheels and hitch installed. No Reserve!