This line is for sale as one lot. 1. Vertical Reciprocating Conveyor (VRC) - 106x80x72 - Roller Dimensions: 94x3 inch diameter - 72" wide roller deck 2. Chain Transfer Conveyor - Space between rollers is 4 feet (size of Transfer deck) - Rollers on each side measure 94x3. - Roller housings on each side measure 72x96x26. -Total dimensions: 72x224x26. 3. Straight chain driven Conveyor - 72x100x26 - 8' rollers 4. 360° rotating turntable conveyor -Base dimensions: 74x58 -Roller dimensions: 40x3 - Conveyor Dimensions: 72x48x26 5. Straight belt driven conveyors (4 of them) - 54x12x12 belts not included 6. Curved belt driven Conveyor - Exterior curve: 224x48x26 - Rollers are 40" long and vary from 2-4.5" wide along curve. 7. Line conveyors (2) - 144x36x24 - Rollers available for this 8. Stacked rollers -96x66x75 - Roller dimensions: 80x3 9. Straight Gravity Rollers (18 of them) - 148x36x6.25 These rollers were stacked 4 high. Legs are available to stack them or they will work in line. 222' run consisting of 18 pieces. 10. 32' decline belt conveyor - This has damage. See last photo.

60" Pallet DIsmantler Motor 10 HP, 220/440V, 3 phase Switch on/off Band saw 228” long x 1-1/4” wide Table dimensions: 60” width x 48” depth Maximum size pallet to dismantle: 60” wide x any length Maximum distance between the horizontal bandsaw blade from table: 1” and up to 3” if the table stop end is cut. Machine dimensions: 115” length X 52” width x 55” height Weight 1,050 lb.

4- Head customer built resaw 6" Wide belt Hydraulic hold down rollers 15 HP Motors on each head Pneumatic tension

Single Head Pallet Notcher - New with warranty! 7.5 HP Motor 220/440 3PH Maximum Notch Size: 9" x 2-1/2" x 1-5/8 Power switch with magnetic starter Cutterhead with 4-stright HSS knives (optional 40 knife cutterhead) Dimensions: 48" L x 36" W x 40" H

Single Head 4 blade Notcher: custom built, lightly used Motor 10 HP, 220/440V, 3 phase Maximum notcher size 9” long x 2-1/2” height x 1-5/8” depth Cutterhead with 4 straight HSS knives installed

Custom Built Single Head Notcher Manual

Custom Built Single Head Notcher Manual

This line will produce 4-5 bags per minute. Outfeed conveyor from each line Optional: Infeed auger and shaving bin

Each system is custom built to fit your specifications. Standard Electric Lateral Chain Feeders include Basic Feeder with transport length of 30" Workpiece width 3/4" - 9-1/4" Min. Workpiece length 12" Drive system with 4 HP total drive system Feed speed range 50 - 250 ft/min (up to 400ft/min available) Thickness 1/4" - 4" Steel flat top chain 60 Cycle per minute Adjustable Fence 35MM Feed Wheel Shafts Options 6'-16' Lateral Chain Feeder Feed Wheel Knurled, Urethane or Light Knurl Hub Options 3/4" or 2" Powder Coating Bridge Side Fence Feed Speeds up to 400 FPM Short Stock Fence 12" Wide Capacty

15MM Cyclonic Air Burner -Refractory and Brick in Good Shape -Suitable for a Large Range of Drum Dryers

Orbital Sander Line 2004 DMC Unisand 2000 Timesavers Model 252-4C

Daewoo G25S Forklift

156" long x 60" wide x 80" high (3) vertical pneumatic Clamping bars (7) clamps that can be placed horizontal or vertical on perforated surface

This unit has been in storage for some time and will need some TLC.

3/4 HP 1725 rpm motor 115/208/230 volt single phase approx. 12” x 30” table Jacobs chuck approx. 3/4” footpedal Assorted fixtures and tooling as pictured.

MANUFACTURER'S SPECIFICATION Motor: - Horsepower: 3 HP - Voltage: 230V - Hertz: 60 Hz TEFC - Phase: 1-Phase - Feed Motor: - Horsepower: 1/6 HP - Phase: 1-Phase - Speeds: 1,550 RPM Drums; 3 to 20 FPM Feed Belt - Sanding Capacity: 12-1/4 in. x 25-1/2 in. - Minimum Sanding Thickness: 1/4 in. - Minimum Length of Unbutted Stock: 6 in. - Drums: 5 in. x 26 in. Aluminum - Sanding Strip Size: 5-1/8 in. x 92-1/2 in. - Dimensions (Assembled): 31 in. x 46 in. x 53 in. - Base Dimension for Mobile Base: 17-3/4 in. x 43 in. - Weight: 418 lbs.

Delta 6" Jointer

Delta Table Saw 5 HP 230 volt 3-phase

Detel M-2H Boring Machine (2) 25-Spindle Boring Heads

671 Diesel Model PTA11112