Optisand L202 Moulding Sander

Optimatic TS-06 Tooth Straightener Manufacturer specs: Every Tooth - Every Run - Every Time Introducing the TS06 automatic bandsaw tooth straightener. This latest Filing Room innovation from OPTIMATIC is designed to work in place of the backfeed on a bandsaw sharpener. The TS06 is timed from the feed of the bandsaw sharpener. Each tooth is examined as it passes through the sensor. When a tooth is not aligned properly it will bend it back to correct it. Teeth are examined on each round of the grinder, giving the tooth straightener the opportunity to examine each tooth several times as the saw is processed and make progressive improvement putting the tooth back in line. A standard 5' resaw can generally be processed in 30 minutes. The TS06 is designed to measure the body of the tooth, just below the grinding burr and just behind the swage or tip. The actual contact point is easily adjustable. It's important to measure the body of the tooth so that we do not cover up problems with swages, shapers, or tippers. - but instead provide them a square, strong tooth to work from. 1. The TS06 has two stations. The first station feeds then measures. 2. The second station bends. Specifications:Connection values:Electrical connetion:220 V 50 Hz or special voltageAir Pressure:1/4? Gas threadAir:Minimum 5 bar air consumption, 1 liter per strokeSaw blade diameter:Saw Wide:From 80 mm to 300 mm wide or special up to 420 mmSaw Long:From 6 m in the grinding machine carousel can be integratedSaw Thickness:0,7 mm to 2,7 mmDimensions:Length:1350 mmHeight:1550 mmWidth:600 mmWorking position:1000 mm can be adapted to grinding heightWeight:210 kg

Optimal 4-Side Canter See photos fro complete specs

7.5 HP 230/460 volt 3 phase 20” blade

9 speed transmission 6 wheel drive 46# rear lockers 23574 miles/24800 hours

These are available on a monthly basis: 49” x 22” x ½” Grade: CCX Species: Douglas Fir 34 units available 140 sheets per unit Approx 5,000 sheets per month available

This system was purchased new in 2011. It is started up every week for 15 minutes. Ready to be removed. FIRE PUMP 2000 USGPM@ 125 PSI UL/ CONTROLLER GRP-GPU 575/3/60 Note: INCLUDED: FIRE VERTICAL TURBINE FIRE PUMP 2000 USGPM @ 125 PSI , UL/ULC/FM APPROXIMATELY 25' COLUMN ONE TORNATECH 200 HP AUTO TRANSFORMER REDUCED VOLT STARTER C/W AUTO TRANSFER SW MODEL GPR/GPU 575/3/60 NEW WET PIPE SPRINKLER SYSTEM FOR PUMP ROOM C/W CONTROL VALVE & FLOW SWITCH TEST HEADER ONE JOCKEY PUMP SERIES GS MODEL 150H20-8, 100 USGPM@180 PSI ONE HOSE RAACK C/W 50 ' HOSE WALL HYDRANT CONNECTION FOR FIRE DEPARTMENT SEISMIC INSTALLATION DRAWINGS C/W HYDRAULIC CALCULATIONS

Deuma RF/S150 A-V

Turbosaw that was used a few times by seller. This machine did not work well with mesquite trees.

Single End Tenoner that will handle straight or curved material. Carves round ended tenons through the use of (2) worktables which independently slide on steel rails. Tables independently adjustable for height and tilt Max width 100mm Max thickness 30mm Max Depth 50mm Table adjustment (vertical) 100mm Tilting 20^ front 15^radial Fence 45^ Spindle motor 2.25KW (3HP) (2) dust hoods Weight 960KG Dims 1320 x 1120 x 1250 mm 230 volt 3phase

2022 Pallet Chief IV Deluxe Stacker 48x48 Capacity

Pallet Band Dismantler

Pallet Repair System Disc Dismantler Pallet size: 3.875" Stringer Width Max. (.098 m) 1.25" Deckboard Thickness Max. (.031 m)

This machine was purchased as "rebuilt" by the manufacturer and never put into service at the current location. Ready to load.

Paul AB920 Rip Saw Scanning Fenceless Infeed Infeed & Outfeed (not including decks) The machine has one fixed and 2 moving blades. The minimum distance between the moving blades is 44 mm (1.73"). The maximum distance between the moving saw blades is 210 mm (8-1/4"). The machine is designed for incoming boards with the following min./max. dimensions Length: 4' - 16' Width: 2" - 19" Ripped widths: 1.75" - 8" Thickness: 1" - 2" 480 Volt, 60 hz., 3 phase electrics 75 HP main motor Automatic edging separation after the saw Feed speed up to 300 fpm Fenceless infeed system with automatic skewing capability 16 width sensors on the infeed system

Peerless Chip Bin MOD 14

This machine was reported to be in running condition when removed from service. Looks like a Pendu. Cannot find a plate on the machine to confirm. this is a single arbor gang and it does not have a sizer. 75 HP Main Motor 5 HP Drive motor

Pendu Stacker No hydraulic pack

4 Head drill station 20' with powered roll case Hydraulic set stops

Good Condition Infeed Hydraulic Power Unit Stacker