Made for Solid and Engineered Flooring 2 Cutting Blades - 10 HP each 4 way adjustability for each blade Servo drive- programmable varying speed for a variable sawmark look Touchscreen Operation 480V 3 Phase Schneider Electronics

1994 Woodtech Bandsaw Model 816420

Specs: Model GH-2 3 Hp, 230/460 volt three phase drive motor Belt drive to spindle arbor design (2) Spindle drill head with adjustable centers Min drill centers 1" Max drill centers 9" Spindle speed 3000 rpm Machine weight 650 lbs Vertical table adjustment 4" 24" wide x 12" long machine work table Pneumatic stock clamping Pneumatic cylinder stroke of drill head Foot pedal pneumatic controls Square D push button motor controls

Yaskawa Motoman UP50N Robot YR-UP50N-A00 Payload 50kg Control Box Teach Pendant Yaskawa Motoman UP50N Robot Type: YR-UP50N-A00 Payload 50kg

Yates A20-12 Planer Infeed Deck Tilt Hoist 575 V Includes: Misc parts, heads and attachments for S4S and T&G. This system was removed from service this Spring. It is ready to load.

The seller has confirmed that this Yates American resaw was in working/running condition when it was pulled from production. It is ready to load! - Vertical resaw - All parts and blades included - Approximately 35 years old - 50-60HP - 440 amp

The frame is a massive, compact and solid casting which takes less floor space for its capacity The feed drive is built to stand up under the hardest kind of services The feed rolls are of such design that the advantages of the open side type of construction are combined with of the advantages of the inside The top and bottom head assemblies are of the most substantial construction The top head chip breaker is made of chilled cast iron section, each section being spring loaded and adjustable The side head spindles are short and of large diameter The side head chipbreaker moves in and out with the head and is also provided with an additional screw adjustment for close setting The bedding is continuous throughout the entire length of the machine

There are two of these systems available. They were recently removed from the current operation and available immediately.

Used Yates American Model B-26, 24” Double Planer, 75HP top, 40HPBottom, top and bottom 10 knife cutterheads, on the fly top and bottom jointers, 3 phase 480volt electrics, slide out lower cutterhead, top fixed cutterhead, 3-3/4” thickness capacity, approx. 20HP hydraulic feed works, power bed raise and lower, sectional pneumatic chip breaker, top infeed/outfeed rubber rollers.

Yates American E-12 End Matcher System for tongue and groove flooring includes: Belt, Straight Line Blade, 3-blades, Infeed conveyor to end matcher, transfer conveyor from first machine to second machine, variable speed outfeed conveyor

220v 3 phase 2hp motor Controls work, motor runs and spindle turns Spindle raising mechanism has pin sheared in bevel gear. Includes overarm casting & mobile base.

Planer Head Set Up Stand

Yuasa saw analyzer, great working condition comes with saw centers, magnifying camera and monitor.

Air Compressor Water Separator Single Phase 115V 16hz Good Condition

Recently removed from service Available immediately

Brewco 4-Head Resaw Seller has a hydraulic unit to go with the machine. No controls. Optional: System can be cleaned up and controls added PER SELLER: this machine is able to pass 7.75" cants it was purchased in Nelson BC 20 years ago it has not run since it is ready to go but has only on off switches and no motor starters per se I have not pulled the machine out to clean and paint and get ready to move it needs cleaned/ painted/ starters for 4-20hp motors/ small hyd unit for feed belt and feed rolls nice machine, I have not operated it but was running when I bought it and has been under cover since will need 5 starters, and a small hyd unit 5 hp, which i can provide this machine is easy to get ready if we have a commitment

This system is no longer needed at the current facility. Ready for immediate removal! - Brewco Wolf Resaw - 4" Blade; 20'4" Long - 40" Bandwheels - 40 HP Main Motor - 10 HP Hydraulic Feed - McDonough Style Guides - Some spare blades - Head moves up/down, not the bed - Approximate dimensions: 9'L x 10'W x 6'H - Also available separately: - 8' Infeed Belt - 16' Outfeed Rollcase

Brewer 5-Head Resaw Return Belt

Brewer 3-Head Resaw Model # BR-3B8X12R

Brewer 3 Head Resaw Model: Golden Eagle 2000 Year: 1998 Blade Size: 2" Voltage: 480 3ph Material Capacity: 7.5" - 12" width Serial #: No Placard Condition: Fully Functional, no rust, Updated electrical panel. Spare Parts: 2" Blades Dimensions: 20' long x 11' wide New Bearing on all wheels front and back. We put a new rubber belt on the infeed, we still have the steel belt infeed if they want to change it back. About 20-40 2” band saw blades included. Saw Head 3 has 1 new motor.