This machine was purchased as "rebuilt" by the manufacturer and never put into service at the current location. Ready to load.

Model P30N 600 V / 3 Ph / 60 Hz Includes Transformer

Paul AB920 Rip Saw Scanning Fenceless Infeed Infeed & Outfeed (not including decks) The machine has one fixed and 2 moving blades. The minimum distance between the moving blades is 44 mm (1.73"). The maximum distance between the moving saw blades is 210 mm (8-1/4"). The machine is designed for incoming boards with the following min./max. dimensions Length: 4' - 16' Width: 2" - 19" Ripped widths: 1.75" - 8" Thickness: 1" - 2" 480 Volt, 60 hz., 3 phase electrics 75 HP main motor Automatic edging separation after the saw Feed speed up to 300 fpm Fenceless infeed system with automatic skewing capability 16 width sensors on the infeed system

This machine was reported to be in running condition when removed from service. Looks like a Pendu. Cannot find a plate on the machine to confirm. this is a single arbor gang and it does not have a sizer. 75 HP Main Motor 5 HP Drive motor

4 Head drill station 20' with powered roll case Hydraulic set stops

Pendu Stacker No hydraulic pack

2016 Pendu 4600 Board Stacker Rollout Conveyor Hydraulic Unit Very Good Condition

Selling as a complete package: Pendu Sharp Chain Scragg (2) 100 HP Motors with soft starts Infeed System Log turner Operator Cab All controls and electrical (2) Log Decks: 3-Strand and 4-Strand Pendu bark conveyor: 30'4" Long with 180 degree tail section, 17" flights 2" high, flights spaced 18-3/4" apart Barn Sweep: Elevated conveyor: 25'4 Long, (2) Hold downs with idlers, chain has 17" flights that are 2" high, leg brackets, Approx 90' of Barn Sweep conveyor with chain and drive motor

Pendu 1400 Drill Station Includes: Some misc drill bits and infeed pieces

Pendu M-4000 Gangsaw 75 HP on bottom and 75 HP on top arbors 20 HP on blower Press rolls are all original and in very good condition Came from sheltered workshop and was never used much Comes with starter boxes Will disconnect and load.

Pendu E-4000 Gang Saw 75 HP on bottom and 75 HP on top arbors 20 HP on blower Press rolls are all original and in very good condition Comes with starters and 3000 amp disconnect box Some hydraulic upgrades Very good condition Seller will disconnect and load

Pendu Drill Machine 14’ long, up to 12” wide and 12” thick 12 drills 40” tall hydraulic pack, pedestal controls, air hold downs, hydraulic up and down Complete electrical boxes, very low usage

2011 Peterson Pacific Horizontal Grinder Power Source: Diesel Engine Mfr: Cat Engine Model: C27 Horsepower: 1000 Has approximate 9050 hours

PictureTally Booth With Scale

PILLAR MACHINE | CMJ-HSK – COPING MACHINE The CMJ-HSK is a machine designed for chip free coping or tenoning of either square or profiled parts without the need for a back-up piece or chip breaker. The CMJ-HSK is manually operated with 2 counter rotating vertical spindles. One spindle clears the leading edge of the rail with the other spindle then moving in and processing the remainder of the components width. This machine has 2 independent HSK spindle motors with a quick-release tool change feature. If you run multiple profiles a day, this will save you hours of time. The CMJ-HSK will provide a clean, tear-out free, end coped/tenoned part every time! THE CMJ-HSK PERFORMS THE FOLLOWING FUNCTIONS: - Coping STANDARD FEATURES: - 8? part width capacity - Counter rotating spindles to eliminate tear out - Heavy duty frame and components - Scissor lock clamp that applies up to 600 lbs. of force (Top Clamp) - Side Clamp - Auto feed carriage - Dual 10 HP HSK Spindles - Air Locking Tooling on each spindle - 5/8? maximum cut depth - Ability to cut multiple parts per cycle - 5? maximum cutter head diameter - Minimum part length 3? - Cycle time: 7 seconds (approx.) - Material thickness: 1/2? to 1? ADVANTAGES OF THE CMJ-HSK: - No backer board or chip breakers required - Tear out free parts every time - Accurate spindle adjustment for tool alignment - Part stays fixed while the carriage moves - Dual Air-Locking Spindles - Side and Top clamps

Pinheiro MF 4-Sided Planer Includes: Knife sharpener and transformer

The seller has confirmed that this Pinheiro planer is in good working/running condition. - Double sided planer with side saw - Complete package - Manual - no year...Motor HP 20 bottom, 10 top

12” blades 1-1/2 HP motors - 3 phase foot pedal control

The seller of this Pneumafil dust collection system has confirmed that it is in great working/running condition and ready to be loaded! - 150HP - Round duct enters the colletor at 48" diameter

The seller has confirmed that this Pneumafil 135 is available. Pneumafil Dust Collector Model 135 (13.5-460-8) 150 hp. The round duct enters the collector at 40" diameter & exits at 64" square