Hazlethorn Pallet Notcher Model A10

Heartwood 3-Head Resaw

LSM 8 2 head wide belt sander · 1st Head: Segmented cross-belt, 5/8" wide segments (86 total) with "CSD" control, abrasive belt size 5.9" x 244", (5,400 mm X 150 mm ) inside chevron belt 5.9" x 191", sanding belt speed 5-12 m/s with 17 HP motor. (Inverter controlled) · 2nd Head: Combination head, with segmented polishing platen, 5/8" wide segments with CSD control, 17 HP motor, 106" x 53" ( 2,620 mm X 1,350 mm ) abrasive belt size. (Inverter controlled) Cleaning brush Vacuum bed

MFA 6 3 heads Pad (inverter controlled) Pad (inverter controlled) brush CSD System 480 V 100 A

HEESEMANN LSM-8 C/L Wide Belt Sander, (2) Heads 53" (1,300 mm) Width cap., (1) Segmented cross-belt & (1) longitudinal combination head with segmented platen. Head Configuration: · 1st Head: Segmented cross-belt, 5/8" wide segments (86 total) with "CSD" control, abrasive belt size 5.9" x 244", (5,400 mm X 150 mm ) inside chevron belt 5.9" x 191", sanding belt speed 5-12 m/s with 17 HP motor. (Inverter controlled) · 2nd Head: Combination head, with segmented polishing platen, 5/8" wide segments with CSD control, 17 HP motor, 106" x 53" ( 2,620 mm X 1,350 mm ) abrasive belt size. (Inverter controlled) Equipped with & Features: · HESSEMANN's patented "CSD" magnetic pressure adjustment system, sensors spaced every 5/8" (16 mm) sense part configuration; (2) mm part thickness variation can be sanded without sand through’s, pressure for each segment can be pre-programmed to provide less pressure on the outer edges or more in the center if required. · The "CSD" computer control will hold approx. (20) programs or part configurations. · Additional features: Outfeed rotary panel cleaning brush with single end adjustment, 2 HP motor, air blast abrasive belt cleaners on all heads. · Variable feed speed from 13 to 82 FPM via Stober drive, 6.5 HP feed drive, motorized thickness opening 1/4" to 3-5/32" maximum. · Belt condition at 80% good.

Heeseman LSM8 Wide Belt Sander

Confirming it is a Heil system. Seller is not sure. Actual dimensions: 42' x 10'6" Triple Pass Drum

Confirming it is a Heil system. Seller is not sure. Actual dimensions: 42' x 10'6" Triple Pass Drum

Heil 15x32 Triple Pass Drum Dryer 8-10 TPH Drying Capacity Webb Burner Complete Dust Collection All Electrical & Controls 200 HP Wood Hog

12'x42' Triple Pass Drum 20 MM BTU Webb Burner Burner feed bin Burner blowers Blower to pull shavings through drum Cyclone BMM 3-level Shaker Screen (2) Outfeed Conveyors Electrical controls

Heil 10'x40' Triple Pass Drum Dryer Trunions Drum is ready to load.

Heil 10.5' x 32' Triple Pass Drum Dryer 1. Jackson Harvester Burner 24 million BTU 2. Fuel Bin 3. Pipe and fan from fuel bin to burner 4. Air lock on dryer 5. 8 X 24 3 pass dryer 6. Trunnions 7. Fans to dryer 8. Pipe to cyclone 9. Cyclone 10. Pipe to fuel bin 11. Fan moving sawdust to fuel bin 12 Hog with 200 HP motor 13 Dust collection system

Hemco Sorter Line System includes: - Unscrambler - Board Singulator - Even end roll case - 34 Sling Bays - 10 Slot Bays - Stacker Outfeed - Trim Saw

Hemple CL-8 Wood Turning Lathe 20” capacity will turn to 1/4” diameter manyal feed but auto cycle up to 400/hour 220 volt 3- phase

Hemple CL-8 Wood Turning Lathe 20” capacity will turn to 1/4” diameter manyal feed but auto cycle up to 400/hour 220 volt 3- phase

Hemple CL-8 Wood Turning Lathe 20” capacity will turn to 1/4” diameter manyal feed but auto cycle up to 400/hour 220 volt 3- phase

HewSaw SL250 Trio sawing line from 2005 This line has already been dismantled and loaded into containers. It is ready to ship! - Consists of log positioning devices, conveyors and three sawing machines. HewSaw sawing line is designed to process logs ranging from 100 mm – 420 mm small end diameter, to 550 mm large end diameter, with length 2.4 - 6.2 m - Feeding speed of the sawing line can be adjusted from 50 m/min to 150 m/min. Top diameter: 100–420 mm Maximum log diameter: 550 mm Cant height in Chipper Canter: 75–410 mm Cant width in Chipper Canter: 75–410 mm Cant height in Rip Saw: 63–310 mm Cant width in Rip Saw: 75–410 mm Saw kerf: 4.2–5.0 mm Chip length: 20–30 mm Sawline 1. Measuring conveyor 2. Log scanner 3. Log positioner 4. Chipper canter 5. Cant scanning conveyor 6. Cant scanner 7. Cant saw 8. Seperating conveyor EK2 9. Cross conveyor 10. Belt conveyor 11. Cant turner 12. Infeed conveyor 13. Rip saw 14. Belt conveyor 15. Belt conveyors under machines, for waste handling 16. All electric boxes

High Tech 20' Trim Saw (10) Blades

Single Head Horizontal Band Re-saw System Model : HP-11P-SMART • Single saw head configuration. • Motor powered set works for accurate saw wheel elevation. • Digital position controller permits accurate saw wheel height positioning. • Automatic blade tension is controlled by hydraulic cylinder. • Variable feed speed by hydraulic motor drive. • The big pressure roller is air cylinder loaded to hold wood down firmly. Specifications HP- 11P-SMART 1. Saves Time and labor costs 2. Pneumatic pressure roller infeed 3. Digital position controller permits accurate saw wheel height 4. Easy to operate and set up Feed speed: 4-27m/min (13-90FPM) Max. cutting height: 250mm (10”) Max. cutting width: 300mm (11 3/4”) Min. workpiece length: 400mm; 205mm with extension set Max. workpiece length: 580mm Distance from blade to conveyor: 4-125mm Saw wheel Diameter: 711.5mm (28”) Saw wheel width: 22.7mm (1”) Saw blade size: 4265 x 27mm (168” x 1’) Blade speed: 2816m/min (9240FPM) Saw Motor: 15kW(20HP) Feed unit: 0.75kW(2HP) gearbox motor with frequency converter Cooling system Oil mist Blade tensioning Hydraulic system Motor for blade positioning: 0.18kW(1/4HP) Dust post: Ø4” x 4 Table height: 902.5mm Machine weight: 951kgs Machine dimensions: 2835 x 2052 x 1678mm (LxWxH)

High Point 12" Resaw with Return Conveyor