SALVADOR - SUPERANGLE 600, ...Pusher Chop Saw. Provides complete chop to length & optimization of wood strips including the elimination of defects. -- Infeed is made of Heavy-Duty steel frame; working height: 1,000 mm (39") from floor level; safety provided by a light curtain. -- Pusher slides on double hardened rails. -- Reading Operation: Uses (2) Sensors: (1) for overall length and the other to read the crayon marks. -- Transmission of power: From motor to the carriage; accomplished by a 50 mm wide steel reinforced toothed belt. -- Part held in place by (2) aligners before & after the blade; insures a square cut. -- Saw box area: Enclosed by interlocking steel cover with a large window for clear view; Saw travels through an aluminum table insert that can be easily changed as needed; High Efficiency motor, IE3 rating, helps keep power consumption at a minimum. -- Technology: Operating software: Customized Windows-based program; designed to be intuitive and specially designed for optimization of the wood. -- Large 19" monitor at operator eye level; PC set up with: SSD Double hard drive with 2nd being a clone to have and be ready to back up in the machine. -- Cut lists: Can be uploaded remotely by network connection or flash drive; chop length optimization can be set for minimum waste priorities. -- Optimizer supports defecting crayons, as well as up to 5-grade qualities. -- Electronics: Multi tap transformer steps down higher voltages; 460 - 600 to the voltage requited by the machine. -- SP 15 Magnetic Strip Measurement: Technology improves positioning from basic encoder standards to absolute measurements of +/- 0.1mm. -- Outfeed: 0° Belt and (1) PC double ejector. For applications of many workpieces cut at angles, it is best to eject the workpieces together with one large rack & pinion ejector. Workpieces are pulled from the Saw on an outfeed belt. - Once the parts are clear of the Saw, the large ejector manages all cuts in 1-push onto the steel table for collection. WORKING CAPACITYMaximum board length before cutting: 5,100 mm (16').Minimum board length before cutting: 500 mm (19.6").TECHNICAL SPECIFICATIONSMain saw power: 15 HP.Saw blade specifications: SA600; Max. 00 mm; dia. bore 35 mm.Maximum pusher reading speed: 60 MPM (200 FPM)Maximum pusher pushing speed 60 MPM (200 FPM)CUTTING CROSS SECTION &#9679 0°: 100 mm x 360 mm / 160 mm x 310 mm. &#9679 +/- 45°: 100 mm x 260 mm / 160 mm / 220 mm. &#9679 +/- 70°: 100 mm x 120 mm / 160 mm x 100 mm.Minimum: 15 mm x 30 mm.Number of cuts within last 40 mm of board One: (1)Maximum workpiece weight: 110 kG (242 Lbs).Power Requirements &#9679 11 kW. &#9679 Primary supply voltages: 220/380/420/440/460/480/560/580/600 V.Pneumatic Requirements &#9679 Compressed air supply: 600 - 800 kPa (6 - 8 bar). &#9679 Maximum air consumption: 300 Nl/min.Dust Extraction &#9679 Intake diameter: 160 mm Upper; 120 mm lower/ &#9679 Extraction System Collection speed: 28 M/s. &#9679 Dust Extraction Capacity: 1

//This machine is in an Auction on exfactoryauctions.com// //Link to machine: http://exf.ac/i61 WHIRLWIND 1000 L Upcut Saw Specifications: 2-3/16" x 8-1/4" Cap., 14" blade cap., 3,450 RPM, left-hand unit feeding from right-to-left, 5 HP BALDOR motor. Complete with: (5 - 90) Cycles/Min; magnetic starter with low voltage controls, air filter, regulator, coalescing filter, and 4" dust chute. NOTE: The above specs are taken from literature and considered accurate. As always please take advantage of the inspection period to verify. Items seen in the background are NOT a part of this Lot.