EXTREMA DCY-750.3 TYPHOON Cyclone Dust CollectorCyclone & fabric filtration dust collection system. -- Powerful two-stage dust collection drops out heavier dust particles through a 1/2 HP Rotary Air Lock (included), allowing you to choose the disposal system, before passing finer particals through the fan and filter. -- (2) Fabric filter bags placed above plastic collection bags. -- Air volume output rated @ 4,850 CFM with 7.5 HP Induction motor with 12" inlet. -- 14-3/4" Steel blower fan impeller and is dynamically balanced. -- Collection bag snap-in ring for easy addition or removal of plastic bag. -- Filter bags filter dust particles down to (1) Micron in size. -- Low noise operation. -- Includes: Standard support frame to allow use with a waste hopper under the cyclone.

EXTREMA DCY-1000 TYPHOON Cyclone Dust Collector. Cyclone & fabric filtration Dust Collection System. -- Powerful 2-stage dust collection drops out heavier dust particles through a 1/2 HP Rotary Air Lock with 10 CFM capacity, allowing you to choose the disposal system, before passing finer particles through the fan and filter. -- (2) Fabric filter bags placed above plastic collection bags; air volume output rated @ 6,400 CFM. -- Equipped with: 10 HP Induction motor, 16" steel blower fan impeller and is dynamically balanced and 12" inlet. -- Includes: Collection bag snap-in ring for easy addition or removal of plastic bag; filter bags filter dust particles down to (1) Micron in size; low noise operation. -- Supplied with: Heavy Duty support frame to allow usage with a waste hopper under the Cyclone.

EXTREMA RC-04 Rotary Air Lock Standard capacity Rotary Air Lock; Cycles waste off of a cyclone dust collector while maintaining internal pressure.Specifications: -- The Rotary Air Lock is an essential device for dust collectors that dump directly into a dumpster or hopper. -- This unit has a 16" dia. lock with a 1/2 HP motor. -- 33 RPM TEFC Direct drive motor. -- 16" Inlet dia. & 16" outlet diameter. -- (8) Rubber blades. -- Does not include electrical controls. -- Features: Approx. 10 Cu. Ft./Min capacity.

EXTREMA DB-100 TYPHOON BLOWER. Capacity 10 HP, 6,350 CFM. -- Solid heavy gauge steel construction. -- Heavy duty dynamically balanced steel impeller, 12" inlet, 14" impeller, 14" outlet. -- Rotatable collection port for use in a variety of applications. -- Safety guards on all inlets. - Complete with magnetic starter. -- Note: 460 Volt available.

EXTREMA DB-150 TYPHOON BLOWER. Capacity 15 HP, 7,900 CFM. -- Solid heavy gauge steel construction. -- Heavy duty dynamically balanced steel impeller, 14" inlet, 25" impeller, 16" outlet. -- Rotatable collection port for use in a variety of applications. -- Safety guards on all inlets. - Complete with magnetic starter. -- Note: 460 volt available.

EXTREMA RC-10 Air Lock Standard capacity Rotary Air Lock; Cycles waste off of a cyclone dust collector, while maintaining internal pressure. -- The Rotary Air Lock is an essential device for dust collectors that dump directly into a dumpster or hopper. -- This unit has a 16" dia. 1 HP - 33 RPM TEFC Direct drive motor -- 16" inlet dia. & 16" outlet dia. -- (8) rubber blades. -- Does not include electrical controls. -- Features: 38 Cu. ft./min. cap.

EXTREMA DB-250 TYPHOON BLOWER. Capacity 25 HP, 10,350 CFM.Specifications: -- Inlet 18", 27" impeller, 20" outlet. -- Solid heavy gauge steel construction. -- Heavy duty dynamically balanced steel impeller. -- Rotatable collection port for use in a variety of applications. -- Safety guards on all inlets. -- Complete with magnetic starter. Note: 460 Volt available

EXTREMA DCY-1220 L3 TYPHOON Cyclone Filtration Dust Collection System. -- Powerful two-stage dust collection drops out heavier dust particles through a Rotary Air Lock, allowing you to choose the disposal system, before passing finer particles through the fan and filter. -- Air volume rated @ 8,800 CFM. -- Unit includes; 20 HP Motor, with a Soft Start already wired in. -- Rotary air lock with a 1 HP motor @ 38 CFM. -- Low noise operation. -- Standard support frame LEG 3 164" clear height x 149" clear width x 91" clear depth. -- Return air filters also available.

EXTREMA DCY-1215 L3 TYPHOON Cyclone Filtration Dust Collection System.Powerful two-stage dust collection drops out heavier dust particles through a Rotary Air Lock, allowing you to choose the disposal system, before passing finer particles through the fan and filter. -- Air volume rated @ 7,600 CFM. -- Unit includes: 15 HP Motor, with a Soft Start already wired in. -- Rotary air lock with a 1 HP motor @ 38 CFM. -- 14" Inlet Low noise operation. -- Standard support frame LEG 3 164" clear height x 149" clear width x 91" clear depth. -- Return air filters also available.

EXTREMA DCY-1425 L3 TYPHOON Cyclone Filtration Dust Collection System. Powerful two-stage dust collection drops out heavier dust particles through a Rotary Air Lock, allowing you to choose the disposal system, before passing finer particles through the fan and filter. -- Free air volume rated @ 10,500 CFM. -- Low noise operation. Equipped with: -- 25 HP Motor, with a Soft Start already wired in. -- Rotary air lock with a 1 HP motor @ 38 CFM. -- Standard support frame LEG 3 164" clear height x 149" clear width x 91" clear depth. Other Options available: Return Air Filters (DCF-5) plus the pipe to connect the Cyclone with the filter and 460V electric rather than 230 Volt.

EXTREMA DC-3250S TYPHOON Fabric Filtration Dust Collection System. With 1-micron dust filtration efficiency this collector will make your shop cleaner, healthier, and more productive.Specifications: -- (6) Fabric filter top bags are mounted above individual plastic collection bags. -- The multi-bag system is placed on sturdy steel legs in a horizontal series. -- 10,000 CFM Output with single-stage blower. -- Additional filtration sections can be easily added. -- Heavy Duty 25 HP induction motor, 18" inlet -- 27" Steel blower fan impellers are dynamically balanced. -- Collection bag snap-in rings for easy addition or removal of plastic bags. -- 1-Micron filter bags with 6 mil plastic bottom collection bags are standard. -- Wye-Delta soft start power switch. Options: Remote control, changing 230 to 460 voltage

EXTREMA DC-232.3 TYPHOON Fabric Filtration Dust Collection System. -- Powerful, portable, and affordable dust collector with roll around casters mounted to a steel platform base. -- (2) Oversized Fabric filter top bags are placed above fabric collection bags. -- 2,950 CFM Output with single-stage blower. -- 3 HP Induction motor. -- Filter bags filter dust particles down to (2) Micron in size. -- Quad 4" dust port adapter.

EXTREMA DC-250.3 TYPHOON Cyclone & Fabric Filtration Dust Collection System. Powerful two-stage dust collection drops out heavier dust particles into a drum before passing finer particles through the fan and filter.Specifications: -- (1) Fabric filter bag placed above plastic collection bag. -- 2,975 CFM rated output. -- 5 HP Induction motor. -- 14-1/4" Steel blower fan impeller is dynamically balanced. -- Collection bag snap-in ring for easy addition or removal of plastic bag. -- Filter bag filters dust particles down to (1) Micron in size. -- Low noise operation. Includes: Sturdy steel tripod cyclone mounting stand. Drum dollie (drum not included).

EXTREMA DC-275.3 TYPHOON Cyclone & Fabric Filtration Dust Collection System. -- Powerful two-stage dust collection drops out heavier dust particles into a drum before passing finer particles through the fan and filter. -- (2) Fabric filter bags placed above plastic collection bags. -- Air volume output rated @ 4,850 CFM. -- 7.5 HP Induction motor. -- 14-3/4" Steel blower fan impeller and is dynamically balanced. -- Collection bag snap-in ring for easy addition or removal of plastic bag. -- Filter bags filter dust particles down to (1) Micron in size. -- Low noise operation. -- Includes: Sturdy steel tripod cyclone mounting stand and drum dolly. (drum not included).

EXTREMA DC-2100 TYPHOON Cyclone & Fabric Filtration Dust Collection System.Powerful two-stage dust collection drops out heavier dust particles into a drum before passing finer particles through the fan and filter.Specifications: -- (2) Fabric filter bags placed above plastic collection bags with 117 Sq. Ft. total cloth area -- 32 Cu. Ft. of storage capacity -- Rated at 6,400 CFM at 16" static pressure output. -- 10 HP Induction Motor. -- Inlet 13" with 16" Steel blower fan impeller that is dynamically balanced.Features: -- Collection bag snap-in ring for easy addition or removal of plastic bag. -- Filter bags filter out dust particles down to (1) Micron in size. -- Low noise operation. Includes: -- Sturdy steel tripod cyclone mounting stand and drum dollie (drums not included).

HOLZ-HER 1329 SPRINT PERFORMANCE EDGEBANDER (W/PRE-MILL & CORNER ROUNDING) + EVA/PUR GLUING TECHNOLOGY: -- Specifications:Features the HOLZ-HER Patented Dual "GLU-JET" EVA & PÜR Zero Joint Technology System.Edge thickness min./max. 0.4 - 12 mm (0.016 - 0.472"); coiled material 0.4 - 3 mm (0.016 - 0.157").Panel thickness 8 - 60 mm (0.236 - 2.362"); workpiece width min. of 60 mm (2.36"); workpiece length min. 160 mm (6.29"). Programmable Logic Control (PLC) for Pre milling, edge feed, glue application, end trimming, flush trimming, radius trimming, scraping, corner rounding, and buffing. -- Pre milling Station (1802):(2) 2.0 kW (2.68 HP) - 12,000 RPM motors; equipped with: "ProLock" quick change flange including height adjustment for optimum utilization of cutters. -- Edge Magazine (1901):Small 3° feed angle thanks to nozzle design with easy feeding of coils, strips & up to 3 mm and solid wood edging up to 15 mm (0.059").Exclusive "Tractor-Belt Feed System", edge guide equipped with automatic guillotine lock-out for safety. -- Pressure Section (1913 Mot):Servo-controlled pressure section with (1) large driven roller and (2) cantered idle rollers. Straight and tapered pressure rollers for perfect glued joints. -- Gluing System (GJ301 Auto):"GLU JET" Hybrid Technology "thin film technology processes EVA or PÜR Glue in cartridge or granulate form.Motorized, programmable glue nozzle (upper glue line) height positioning. Automatic reload of the glue cartridges or granulated. Workstations: -- End Trimming Unit (1918-P):Front & Rear - (2) 0.35 kW (0.5 HP) - 9,000 RPM motor each; unipoint swivel axis for no re-indexing when changing from flush to bevel end trim (0° - 10° bevel)."PCS" programmable pneumatic changeover from flush to bevel. -- Multi-Function Trimming Unit (1827MOT4): (2) 0.65 kW (0.87 HP) - 12,000 RPM each motor, Servo motors: (1) for horizontal copy wheel & (1) for tool spindle position; programmable top & bottom unit. Unipoint design with no second adjustment with pneumatic, programmable tilt action for changing the degree of bevel.Digital counters for vertical copy wheel position and pneumatic air cylinder for in/out pre-positioning of trimming motor. -- Corner Rounding Unit (1833 MOT4):(2) motors with 0.22 kW (0.30 HP) - 9,000 RPM, for linear edge trimming or vertical corner rounding with (4) Servo programmable positioning motors; Up to 3 mm edge thickness and workpiece thickness min./max.8 - 60 mm (0.31 - 2.36"); max. feed speed 18 MPM (59 FMP) up to 25 mm panel thickness; 26 - 38 mm panel thickness,16 MPM (52 FPM); 39 - 60 mm panel thickness, 2 MPM (6 FPM). -- Profile Scraping Unit (1929-MOT2): Top/Bottom Servo motor controlled, programmable knife position for PVC edges, reversible insert carbide knives.Equipped with air jet blowers and chip collector box. -- Glue Scraping Unit (1964):Flat, Top/Bottom, ball bearing guided and pneumatic controlled. -- Buffing Station (1940):Top & Bottom buffing motors with - 150 mm

HOLZ-HER 1321 SPRINT EDGEBANDER WITH PRE-MILLING & CORNER ROUNDING Specifications: 0.3 - 15 mm Thickness edgebanding capability (3 mm coil or 15 mm max. strip); 6 - 50 mm panel thickness, workpiece width min. of 60 mm; workpiece Length min. 180 mm; Feed speed 12.5 MPM (41 FPM). -- Programmable Logic Control (PLC) for Edge feed, glue application, end trimming, flush trimming, radius trimming, scraping, corner rounding, and buffing. -- Programs can be easily created and recalled at will; screen with graphic interface makes programming easy, icon of each unit may be brought up on the screen to show the operator the status of the unit and the parameters which can be programmed; Edgebander can be operated manually when required, without necessity to write a program.Machine configuration: -- Pre-milling station "1961", (2) 2.0 kW - 12,000 RPM motors; "1903" Edge strip Magazine; (1) Universal magazine for solid edges, strips, and coiled material.Utilizes motion detector to ensure accurate, trouble-free positioning of edge material; exclusive "Tractor-Belt feed System", edge guide equipped with automatic guillotine lock-out for safety, 3° approach angle allows easy feeding of large wood edges. -- "1906-M" Gluing Station - Cartridge System: Servo controlled pressure section with (1) large driven roller & (2) cantered idle rollers.Workstations: -- "1918 HF" Front & rear end trim unit (0.35 kW - 9,000 RPM motor each), Uni-Point axis for no re-indexing when changing from flush to bevel end trim (0° - 10° bevel),"PCS" Pneumatic Changeover from flush to bevel from control panel. -- Top & bottom flush trim unit "1823" (0.6 kW - 300 Cy HF motors 18,000 RPM Motor ea.), SIKO digital readouts. -- "1942-M" Servo controlled Top & Bottom combination flush/chamfer & radius unit (0.6 kW - 18,000 RPM each motor), Uni-Point design for no second adjustment when changing the degree of bevel, air jets for debris removal, digital counters, and includes 2-position "PCS" Pneumatic Changeover System from flush to radius from control panel. -- "1929" Servo controlled Top & bottom PVC scrape station: Reversible insert carbide knives, equipped with air-jet blowers; "PCS" Pneumatic Changeover System moves Scraper Unit in-and-out from control panel; Chip Collector Box. -- "1832" 1-Motor Corner Rounding unit: For edges up to 3 mm edge thickness; incl. Tooling R = 3 mm. -- Pneumatic controlled Top & Bottom glue scrape station -- "1940" Top & bottom buffing station: Possible to adjust in any direction (vertical tilt is 0° - 5°, horizontal Swivel is 0° - 20°); 1,440 RPM wheel rotation.Equipped with: -- Microprocessor for line control & glue temperature, 10 KVA frequency changer, outboard panel support, and sound enclosure w/interior lights over enclosed workstations of the machine, & used tooling on the stations.

HOLZ-HER - 1619, ...Boring Machine (Construction & Line Boring) -- Specifications:(19) Spindles on 32 mm centers; bores vertically from top and horizontally from the rear; repositions via manual air shock assisted tilting.2 HP Motor with: 2,800 RPM Gear driven boring head. -- Features:4-Position turret style depth stop for boring depth and a 4-3/4" max. stroke of boring head.24-3/4" Working width; 27-1/8" max. panel width; 19-1/2"; x 38"; x 32-1/2"; H table size. -- Equipped & Complete with:RH & LH Indexing fence with flip stops; (2) indexing pins (for continuous line boring); (3) 4" dia. pneumatic holddown clamps; foot pedal actuator; magnetic push button starter. -- Actual Model is: HOLZ-HER 1619Dimensions of this specific machine with pallet: 52" x 40" x 65" H.Dimensions of this specific machine when vertical: 52" x 37" x 60" H.Dimensions of this specific machine when horizontal: 52" x 51" x 46" H.

HOLZ-HER 1488V TRIATHLON (W/PRE-MILL & CORNER ROUNDING): -- Specifications:PC Controller which has the ability to program all functions including, thickness, edge feed, glue application, side pressure, end trimming, flush trimming, bevel/radius trimming, shaping, buffing. Virtually eliminates set-up time by selecting & loading program that automatically activates all functions simultaneously.Basic Capacity Data: Max. 1" (25 mm) solid wood banding, thin PVC, veneer, HPL & 3 mm PVC cap., 2-3/8" max. panel thickness and 7" min. panel length.Front-End Equipped With: -- Granulate Gluing System (#1907), w/flat glue-nozzle only 3° angle of approach ideal for solid wood edgebanding & "quick melt" feature. -- Automatic Edge-Magazine (1901) for coil, strip & solid wood edgebanding with TRACTOR-BELT feed system, with Heavy Duty guillotine for 4 mm PVC. -- Pressure Section (1926K MOT) with (3) large dia. rollers, each w/individual pneumatic plunge and pressure control; Programmable with servo motor positioning. Powered 1st roller with electronic speed control synchronized with chain feed speed.EDGEBANDING WORKSTATIONS: -- End Trimming Unit (#1916.1), (2) "HF" motors @ (1 HP - 2,480 RPM ea.) with "Uni-Point Swivel", quick change from flush to 0° - 15° bevel programmable from operator panel. -- Flush Trimming Unit (#1962), (2.6 HP - 200 Cy HF motors), w/servo controls, (3) motors, for compl. workstation forward/backward, vertical copy-wheels +/-. -- Fine/Bevel/Radius Trimming Unit (#1966M), w/5-axis servo motors, (1.5 HP - 200 Cy HF motors), bevels 0° - 45°, plus SIKO digital readouts. -- Scraper Unit (#1927), "Super Duty" for positively smooth finishing thick PVC for radius range from 2 - 5 mm, vertical & horizontal tracing wheels, positioning enabled through (1) servo motor function from control panel, as well as SIKO readouts for easy setup. -- Edge Shaper (#1932 MOT), w/jump control for vertical or horizontal shaping or grooving, 3.8 KW (5 HP) spindle motor, 12,000 RPM spindle speed, max. cutter dia. 135 mm (5.3"), max. cutter width 60 mm (2.36"), servo motor positioning for shaper base and SIKO digital readouts. -- Flat Glue Scraper (#1964), top & bottom for removal of potential glue squeeze-out w/air pressure nozzles to prevent shavings build-up. -- Jump Buffing Unit (#1944), w/programmable jump action for cleaning & polishing of edges (two 0.25 HP - 3,600 RPM motors), tilts 0° - 5°. -- Edge Sanding Unit (1935), vertical oscillating, belt size 120 x 2100 mm (4.75 x 82.75"), pneumatic pressure control for sanding pad, anti-dubbing device for leading & trailing edges.Equipped with and Includes: -- Microprocessor with color LCD screen, 90% of all set-ups can be adjusted from the control panel, programmable for a large variety of edges like solid lumber, veneer strips or coils, HPL, thin & thick PVC. Line control so there are no mechanical limit switches along the chain track. -- Variable feed speed from 8 - 24 MPM (26 - 67 FPM), panel overhang

HOLZ-HER 1327 SPRINT CLASSIC SPECIAL EDGEBANDER + EVA/PUR GLUING TECHNOLOGY: -- Note: This is a "SPECIAL MACHINE for THIN TAPE Only". -- Specifications: Features the HOLZ-HER patented dual "GLU-JET" EVA & PUR Zero Joint Technology System.Edgebanding capacity: Edge thickness min./max. 0.4 - 8 mm (0.02 - 0.31"); coiled material 0.4 - 3 mm (0.016 - 0.157").Workpiece thickness: 6 - 60 mm (0.23" - 2.36"); Workpiece width min. of 65 mm (2.56").Workpiece length: Min. 160 mm (6.29"); variable feed speed 10 - 18 MPM (33 - 59 FPM). Machine Infeed: -- "Open Space" for Pre-milling Station "1802": (2) 2.0 kW (2.68 HP) - 12,000 RPM motors.NOTE: This machine is not equipped with the Premilling Station, but it can be added. -- Edge Magazine "1903":For coil & strip processing; utilizes motion detector to ensure accurate, troublefree positioning of edge material.Exclusive "Tractor Belt Feed System": Edge guide equipped with automatic guillotine lockout for safety.3° Approach angle allows easy feeding of solid wood edges. -- Pressure Section "1913 Mot":1-Axis Servo controlled adjustment of the edge thickness.Pneumatic Plunge controlled pressure section with: (1) Large driven roller and (2) cantered idle rollers. -- Gluing System "GJ301Auto":Glue Jet Hybrid Technology: Processes "EVA" or "PUR" glue in cartridge or granulate form.Motorized programmable glue nozzle (upper glue line); height positioning. approx. 3-minute heat up time. Workstations: -- End Trimming Unit "1918P": Front & Rear; 2 x 0.45 kW (0.6 HP) - 9,000 RPM each motor.For Straight or Chamfer trimming with: "UNI-POINT Axis for "PCS" pneumatic changeover/swiveling up to 10° bevel. -- Combination Trimming Unit "1827": Top & Bottom; 2 x 0.65 kW (0.87 HP) - 12,000 RPM each motor; for T & B Flush/Bevel/Radius trimming. - "ProLock" Clamping System for rapid tool change.Manual edge radius adjustment up to 3 mm & chamfer adjustment up to 15° with a max. edge thickness of 6 mm. -- "Open Space" for 2nd T & B Trimming Unit.NOTE-1: This machine is not equipped with the 2nd T & B Trimming Unit, but it can be added. -- "Open Space"for Profile Scraping Unit "1929P". NOTE-2: This machine is not equipped with the Profile Scraping Unit "1929P", but it can be added. -- "Open Space" for Finish Scraping "1964". NOTE-3: This machine is not equipped with the Finish Scraping "1964", but it can be added. -- "Open Space"for Buffing Unit "1940". NOTE: This machine is not equipped with the Buffing Unit "1940", but it can be added. Operator Interface: -- HOLZ-HER "PPC 231" Power-PC + "Windows-like" Operating System. - 15" SVGA Flat "Touchscreen" control.USB Connection & Ethernet network connection ready; programs can be easily created and recalled at will. Graphic interface makes programming easy; icon of each unit may be brought up on the screen to show the Operator the status of the unit and the parameters that can be programmed.Edgebander can be operated manually when required, without necessity to write a program.C