VANTEDGE MM 6.0 9 C-MOTION Edgebander with Pre-milling & Corner Rounding (EVA & POLYOLEFIN adhesive ready).Specifications: -- 10" Color Tough Screen PLC. The PLC controls all work units and the adhesive thermostats with 1-touch Icon Programmable selections, Photo Indicator Alarms to easily troubleshoot, and Swivel Control Panel.Tape and Panel Infeed System: -- 750 mm Coil support table, heavy-duty large solid polished steel panel in-feed fence guide system, Large industrial digital adjustment for the Pre-Mill panel material removal amount. Top Pressure Beam Adjustment: -- Automatic adjustment from the PLC control, Red LED panel feed indicator light for correct panel spacing, Pneumatic Pop Up Stop system -- Working Capacity: Edgebanding thickness, 0.4 - 3 mm capacity. Min. panel width 85 mm (3.3"); min. panel length 125 mm (4.9"); panel thickness 10 - 50 mm (0.39" - 1.96"), Edge Height 55 mm (2.2").Equipped With: -- Dual 3 HP Pre-milling Motors w/Diamond Cutter Heads, Misting Unite w/Large Dual Dust housing ports to help clean the Pre-Milling system, quick change Glue Reservoir and Pressure Section/Infrared Heat Lamp system; consists of Heavy Duty Guillotine to cut 3 mm coil materials, (4) pneumatic polished Pressure Rollers with manual digital adjustment to edge thickness, (1) Rubber Infeed Tape Roller, (1) Metal Infeed Tape Roller; Direct Universal Drive system - NO Chains. Unit with "Auto-set" automatic intervention, Strip & Coil Edge magazine, automatic shear type guillotine. -- Hot-Melt Glue System: Teflon-coated glue pot, digital thermostats with automatic kick-down when the machine is in idle mode.Workstations:End Trimming Unit: -- Dual 0.5 kW (.67 HP) high-frequency End Trim motors on precision "Auto Lube" Linear Guideway. 90 to 10° pneumatic tilt cut adjustment. Electronic sensors to safely monitor motor positions. Thumb screw pneumatic adjustments for simplicity. Tilting Super Finish Top & Bottom Trimming Station: -- Dual High Frequency 0.65 kW (.75 HP) motors with Combi Finish insert tooling, Top Servo-driven positioning of motors for different edge trimming profiles & positions. Corner Rounding Unit: -- Motors on precision billet aluminum swing tracer arms with pneumatic guidance and Face Copy system. The (2) independent motors can be adjusted to match tape thickness via digital scales. Profile Scraping Unit: -- Top, Bottom & Side Copy wheels to properly follow your panels edge, Triple Copy System for panels with blind Dados & Hinge cup holes., digital adjustment for fine-tuning the unit to the proper tape thickness. -- Flat Scraping Unit: Large copy wheels, Insert tooling, adjustable panel spray mist cooling & cleaning system for special materials and composites, adjustable dual Buffing Wheel system, Dual Hot Air Blowers. Buffing Unit: -- Top & bottom Buffing Unit, 0.5 HP (0.37 kW) - 2,800 RPM motors), units tilt 0° - 30°.Complete With: -- Insulated sound enclosure overall trim stations with a split dust hood,

For pre-glued PVC, veneer, & melamine laminate coil stock; 0.4 - 1.2 mm edge thickness and up to 35 mm panel thickness cap., automatic coil feed. -- Equipped with: Electronically controlled temperature setting for hot air blower, 3,000 watts for up to 650° F temperature, (1) Min heat-up time. -- Guillotine type front & rear end trim (with fast speed, flying knife), top & bottom flush trims with single motor drive to cutterheads. -- Overhead belt type feeder, 16 FPM feed speed. - Mounted on machine base with panel support table.

VITAP RC 92 Semi-Automatic Top & Bottom Edge Trimmer – New, Never Used!Specifications: -- For straight & curved edgebanded panels. -- Max. edge thickness 3 mm (0.12"). -- Panel thickness 10 - 60 mm (0.39" - 2.36"). -- Table size 27" x 31".Equipped with: -- (2) 0.55 kW (0.7 HP) - 12,000 RPM Spindle motors. -- Large dia. guide bearings to ensure precise trimming of edges.NOTE: Sold "As-Is" Without Warranty!

VITAP - ECLIPSE 2.0, ...Semiautomatic Contour (Curved Panel or Round Tables) EdgebanderSemiautomatic Contour Edgebanding and Trimming for Panels including: -- Concave shaped panels. -- Convex shaped panels. -- Straight panels.(3) Methods of Operation: -- Manual: Via the use of a foot pedal control for the guillotine. -- Laser: By entering the length of the desired dimension into the PLC, the guillotine will engage automatically. -- Smart Laser: Guillotine engages automatically when the high-definition laser detects the starting point of the applied edgeband with no need to measure/enter the length.Standard Specifications: -- High productivity and flexibility. -- Application for big and small shaped panels. -- Reinforced hinged holding arm with vacuum table to hold large pieces for edging and trimming. -- Color touch screen HMI 7";.(4) Control Pedals: -- Pedal to start the automatic feeding and manually engage guillotine. -- Pedal for slowing down the feed to process tight radii (turtle speed). -- Pedal for opening/closing the trimming head. -- Pedal to engage suction table vacuum.Glue Station: -- Teflon coated glue pot with 1 kG / 2.2 Lbs capacity. -- Quick disassembly system. -- Supports PUR or EVA Hotmelt Glue. -- Amount of glue applied is adjustable., -- Programmable glue temperature. -- Automatic guillotine for edgebands up to 3 mm x 45 mm. -- (2) Side rollers to follow the contour of the workpiece. -- Bottom support roller tilts after edgebanding for easy release of the panel. -- Variable speed for turtle speed adjusted by potentiometer.Laser for an automatic speed adjustment for complex panel shapes with the help of a potentiometer. -- Utilizes 2 x 800 W heating elements with a thermoregulator and electronic temperature control.Trimming Station: -- Trimming unit with: (2) Motors, approx. 0.5 kW / 0.7 HP high frequency, 15,000 RPM motors. -- Upper, lower, and front contour copy rollers, -- Auxiliary working table that can be raised for trimming small pieces. -- (2) Brazed cutters: R=3, Z = 6. -- Trimming Station with: Pneumatic tilting to allow trimming of big pieces.Technical Data: -- Dimensions of the machine: 2,000 mm (6’-6";) x 2,000 mm (6’-6";) x 1,700 mm (5'-7";). -- Weight: 600 kG/1,323 Lbs. -- 10 - 60 mm Panel thickness range. -- 1 - 3 mm Band thickness range. -- 13 - 64 mm Band height range. -- Connection data: 230 V, 3-Phase, 60 Hz.

CANTEK MX350 EDGEBANDER (W/ PRE-MILLING): -- Specifications:0.4-3 mm Edge thickness, panel thickness 8~45 mm, min. panel width 100 mm (4″), min. panel length 170 mm (6.7″). Equipped with: -- Quick melt Teflon coated glue pot 2.5 Lb capacity. Two spring loaded pressure rollers (One driven, one idling). Automatic coil feed PVC/ABS up to 3mm thick, pneumatically operated guillotine. Laminate strip material can be hand-fed. PLC control system with LED display and keypadWorkstations: -- Pre-Mill station with (2) 1.1 Kw 12,000 RPM trim motors 32 mm (1.25") max. material thickness. -- Single motor front and rear edge trim station. -- Top & bottom trim station with insert knife cutters for radius trimming & bevel trimming. -- Top & bottom scrape station 2 mm radius. -- Top & bottom buffing. -- Feed speed 29 FPM

CANTEK MX340M EDGEBANDERThe MX340 from CANTEK is designed to be a compact, and durable edgebander. -- This machine is equipped with end trimming, flush trimming, PVC scraping, and buffing. -- The CANTEK MX340 Edgebander is operated through a PLC control system with an LED display and keypad.Specifications: -- The MX340 handles panel thickness of 0.315" up to 1.77" (8 mm to 45 mm), -- The coil feed accepts edgebanding from 0.4 mm to 3 mm thick, and strip material can be hand-fed. -- The conveyor feed speed is 29.5 FPM (fixed).Work stations: -- Heated infeed fence for optimum glue penetration. Large capacity Teflon-coated glue pot (2.64 Lbs). -- Pneumatically operated guillotine for up to 3 mm thick banding, followed by spring-loaded double-pressure rollers. -- Single front/rear trimming unit 0.3 HP motor. -- Double top and bottom trimming units (2) 1/2 HP motors. -- Top and bottom scraper/radius scraper. -- Top and bottom buffing station (2) 0.16 HP motors.Note: Edgebander was used for approx. 1 year before health issues forced closer of shop. Has been stored covered since.

CANTEK MX340M EDGEBANDERThe MX340 from CANTEK is designed to be a compact, and durable edgebander. -- This machine is equipped with end trimming, flush trimming, PVC scraping, and buffing. -- The CANTEK MX340 Edgebander is operated through a PLC control system with an LED display and keypad.Specifications: -- The MX340 handles panel thickness of 0.315" up to 1.77" (8 mm to 45 mm), -- The coil feed accepts edgebanding from 0.4 mm to 3 mm thick, and strip material can be hand-fed. -- The conveyor feed speed is 29.5 FPM (fixed).Work stations: -- Heated infeed fence for optimum glue penetration. Large capacity Teflon-coated glue pot (2.64 Lbs). -- Pneumatically operated guillotine for up to 3 mm thick banding, followed by spring-loaded double-pressure rollers. -- Single front/rear trimming unit 0.3 HP motor. -- Double top and bottom trimming units (2) 1/2 HP motors. -- Top and bottom scraper/radius scraper. -- Top and bottom buffing station (2) 0.16 HP motors.Note: Edgebander was used for approx. 1 year before health issues forced closer of shop. Has been stored covered since.

CANTEK MX340M Edgebander (Single Phase):The MX340 from CANTEK is designed to be a compact, and durable edgebander. -- Equipped with end trimming, flush trimming, PVC scraping, and buffing. -- The CANTEK MX340 Edgebander is operated through a PLC control system with an LED display and keypad.Specifications: -- The MX340 handles panel thiknesses of 0.315" up to 1.77" (8 mm to 45 mm). -- The coil feed accepts edgebanding from 0.4 mm to 3 mm thick, and strip material can be hand-fed. -- Conveyor feed speed is 29.5 FPM (fixed).Work stations: -- Heated infeed fence for optimum glue penetration. Large capacity Teflon coated glue pot (2.64 Lbs). -- Pneumatically operated guillotine for up to 3 mm thick banding, followed by spring loaded double pressure rollers. -- Single front/rear trimming unit 0.3 HP motor. -- Double top and bottom trimming units (2) 1/2 HP motors. -- Top and bottom scraper/radius scraper. -- Top and bottom buffing station (2) 0.16 HP motors.Also available in 220V/3PH/ 60 Hz

CANTEK - RapidEdge Pro, ...Edgebander w/Premill & Corner Rounding: -- Specifications:0.4 - 3 mm Edge thickness; strip material can be hand fed; panel thickness 0.315" - 1.77" (8 - 45 mm); min. panel length 6.7" (170 mm); min. panel width 3.54" (90 mm). 0.4 kW Heated infeed fence for better glue adhesion; 2 HP (1.5 kW) feed motor with fixed feed speed of 29 FPM (9 MPM).Equipped with: -- Premill Unit:(2) 2 HP (1.5 kW) - 12,000 RPM each counterrotating cutterheads for removing up to 3 mm of the panel edge. -- Glue System:Quick-Change 1.2 kG Teflon coated glue pot is designed for EVA hot melt glue. The glue pot is a Quick-Change type and can be removed and replaced in less than (1) minute.Spring-loaded Pressure Unit with (2) pressure rollers.The Guillotine shear can rough trim coiled material up to 3 mm in thickness. Pressure rollers section consists of : (1) Large driven roller followed by a smaller one. Workstations: -- End Trim: (1) 0.29 HP (0.22 kW) - 12,000 RPM Single motor end trim system with (2) saw blades; unit is mounted on high precision linear guide rails. -- Rapid Top & Bottom Trim:The RAPID adjustment system uses a pneumatic 3-position adjustment to quickly change from 0.5 mm to 1 mm, to 2 mm edgebanding. This is done directly from the Control Panel.(2) 0.5 HP (0.37 kW) - 12,000 RPM high frequency motors for Top & Bottom trimming of the panel; each motor has an inset knife cutterhead that can be adjusted from flush to beveled finish for thin edges and radius trimming (2 mm radius). -- Nesting Function:Nesting kits are installed on the Top & Bottom trimmers and scraping units to ensure they properly trace the panel when predrilled for hinge holes. -- Corner Rounding:(1) 0.5 HP (0.37 kW) - 12,000 RPM, high frequency single motor Corner Rounding Unit. Quick change corner rounding motor for fast changeover from 1 mm to 2 mm radius on the ends.Unit can process between 0.4 - 3 mm and up to a board thickness of 1.77" (45 mm).The multifunctional cutter can round straight or radius edges with a 2 mm radius cutter. -- Profile Scrappers:Multi-radius scrapers allow operator to apply a 1 mm or 2 mm radius on the Top & Bottom of the panel. -- Flat Scrappers:Flat insert knives designed to remove any excess glue which remains on the surface of the panel after applying the edge due to squeeze out. -- Buffing Units:(2) 0.2 HP (0.12 kW) - 3,000 RPM motors, Top & Bottom Buffing units leave a super finish on ABS & PVC edging and removes any discoloration on the edges. --Release Agent Spray Unit:Applies release agent to the Top & Bottom surface of the panel before applying the glue allows for simple removal of any excess glue.The unit is located before the Premilling Station so any overspray which gets on the edge will be milled off to ensure proper bonding. -- Cleaning Agent Spray Unit:The Cleaning Agent System sprays the Top & Bottom edge before the Buffing Unit & designed to polish the edge and loosen any excess glue residue on the surface of

CANTEK MX-370P EDGEBANDER (W/ PRE-MILL & CORNER ROUNDING): --Specifications:0.4 - 3 mm Edge thickness, panel thickness 0.315" - 1.77". Minimum panel length 6.7", minimum panel width 3-¾". Heated infeed fence for better glue adhesion. Fixed feed speed 29 FPM.Equipped with: -- Pre-mill (2) 1.5 kW each (12,000 RPM) counter-rotating cutter-heads for removing up to 3mm of the panel edge. -- Quick change 1.2 kg Teflon-coated glue pot is designed for EVA hot-melt glue. The glue pot is a Quick-Change type and can be removed and replaced in less than 1 minute. -- Guillotine shear: The guillotine shear can rough trim coiled material up to 3 mm in thickness. Pressure rollers section consist of one large driven roller, followed by a smaller one. Workstations: -- End Trim: The end trim system is a single motor with (2) saw blades. The unit is mounted on high-precision linear guide rails. -- Top & bottom trimmers with (2) high-frequency motors for top & bottom trimming of the panel. Each motor has an inset knife cutter-head which can be adjusted from flush to beveled finish for thin edges, and radius trimming (2 mm radius). Single motor Corner Rounding Unit Can process between 0.4 - 3 mm and up to a board thickness of 1.77" (45 mm). The multifunctional cutter can round straight or radius edges with a 2 mm radius cutter. -- Radius scraping unit fine-tunes the edge radius while removing knife marks during the milling process on radius edging. Insert knives have a 2 mm radius. -- Buffing unit leaves a super finish on ABS and PVC edging and removes any discoloration on the edges.

CASADEI FLEXA 47 RMA8 EDGEBANDER WITH PRE-MILLSpecifications: -- 0.4 mm - 3 mm Max. edge thickness cap., (0.5 mm to 3 mm for solid strip edge thickness). 8 mm - 50 mm (0.3" - 1.97") panel thickness cap. (when edgebanding 3 mm PVC max. thickness is 40 mm). -- Minimum panel dimensions 80 mm wide x 140 mm long (3.15" x 5.5"). -- Automatic feed of coil banding and semi-automatic strip fed magazine (strips 1- 3 mm max.) with 3 mm PVC cap. guillotine.Equipped with: -- Teflon coated glue pot w/fast (10 - 12) Min heat-up time; 1 Kg. capacity. -- Guillotine to cut edgebanding in coils up to 3 mm thick. -- Pneumatically controlled pressure section with (3) pressure rollers; 1st drive, (2) idle.Workstations: -- Cutting group moves on rounded ways made of hardened steel, to guarantee high precision and reliability; cutting movement from the top of the panel is synchronized by the PLC control. -- Pre milling unit with 3 HP - 8,300 RPM High Frequency motors. -- Single motor, double end trimming saw unit with (1) 0.25 HP - 12,000 RPM High Frequency motor. -- Top & Bottom Trim station with (2) 0.45 HP - 12,000 RPM High Frequency motors; unit features adjustable copying on vertical & horizontal floating movements, adjustable cutterhead position by mechanical digital readouts, quick release (electrical & mechanical). -- Includes (2) 3 mm radius cutters. -- Top & Bottom 3 mm scrape station -- Top & Bottom Buffing unit with (2) 0.20 HP - 1,400 RPM motors. -- Fixed feed speed 23 FPM. -- Actual Model is CASADEI FLEXA 47 RMA8

CASADEI ALA 23 EDGEBANDER WITH CORNER ROUNDING0.4 - 15 mm (1/2") Edge cap., panel thickness 10 to 60 mm (.39" to 2.36"). Minimum panel length 120 mm (4-3/4") and 55 mm (2-1/8") minimum width. Equipped with: -- Quick heat-up glue system,(approx. 12 Min) 1.5 Kg glue pot capacity. -- Pressure roll section with (3) rolls - one driven. Pneumatic cut-off guillotine.Workstations: -- Double end trim, chamfers 0° - 15° -- Top & bottom flush/radius trim, bevels 0° - 15°. -- Double motor Corner Rounding station -- Top & bottom scraping for 3 mm radius, -- Top & bottom buffing (0.25 HP - 2,800 RPM motors).NOTE: Seller states that the buffing unit appears to have an electrical issue and is not currently being used by the current owner";Actual Model: "ALA 23 R"

CASADEI ALA 21 COMPACT EDGEBANDER SINGLE PHASEEdgebanding thickness from 0.4 mm to 1.2 mm thick; panel thickness from .8 to 40 mm (.32" to 1.57"), min part width 65 mm (2.55") min part length 140 mm (5.51"). Feed speed 9 MPM (30 FPM)Equipped with: -- Quick heat glue pot (10 to 12 minutes) with 1 Kg (2.2#) capacity. Pneumatically operated guillotene cut-off a double roll pressure section (One driven, one idiling)Work stations: -- Single motor end trim for leading and trailing edges. -- Adjustable dual motor top and bottom trim with straight/curved inserts.

CASADEI - FLEXA 37 M-5, ...EDGEBANDER (W/PREMILL & CORNER ROUNDING): -- SpecificationsEdge material thickness 0.4 - 3 mm coil & 6 mm (0.25") strips. Min./max. panel thickness 8 - 60 mm (0.31 - 2.36"). - Min. panel width 80 mm (3.1") and 140 mm (5-1/2") min. length.Equipped with: -- Premilling Unit: (2) x 3 HP - 8,300 RPM High Frequency motors with counter-rotation. -- Automatic Coil & Strip Feed Magazine with: Heavy Duty 3 mm PVC cap. Guillotine. -- Gluing Unit: Teflon coated quick-change glue tank; approx. 10-minute heat-up time, programmable temperature control w/timer if machine idles to prevent glue overheating/burning. -- Side Pressure Unit: 3-Roll pressure unit w/1st roller power; driven via clutch with pneumatic in & out positioning; (2) idler rollers.Workstations: -- End Trimming Unit:Front & rear end trim, (2) x 0.3 HP - 12,000 RPM ea. motor with pneumatic tilting feature (0° - 15°) from the control panel. -- Top & Bottom Trimming Unit: Combination flush/bevel/radius trimming (2) x 0.65 HP - 12,000 RPM ea. motor; tilts from 0° - 25°. Pneumatic 3-position presets programmable from the control panel. -- Corner Rounding Unit: 2-Motor Corner Rounding unit for leading & trailing edges. -- Edge Scraping Unit: Top & Bottom PVC Scraper for up to 3 mm radius; complete with 3 mm scrape shaving collection box. - Programmable, pneumatic exclusion on/off. -- Buffing Unit:Top & bottom buffing unit; (2) x 0.2 HP - 1,400 RPM ea. motor each; tilting range 8°.Controller: -- "MEGA 300 TS"Sequential motor start, 12" color touch screen, up to (100) programs capacity; maintenance alarms & machine use statistics.Complete with:&#9679 Chain feed motor; feed speed 11 MPM (36 FPM) &#9679 (2) Rows of upper pressure wheels in holddown beam &#9679 Adjustable material support Outrigger &#9679 Sound & Safety Hoods &#9679 Tooling: (1) Ued set of tooling in the machine, cutterheads are combination flush/bevel/radius &#9679 Original Factory Machine documentation.Actual Model is: CADADEI FLEXA 37 M-5. - Sister model to an SCM Edgebander.

CASADEI FLEXA 208-MA-8 EDGEBANDER (W/PRE-MILL & CORNER ROUNDING): Specifications: -- Edge material thickness 0.4 - 3 mm coil & 8 mm (0.314") strips ~ min/max panel thickness "all units" 10 - 45 mm (0.39" - 1.77") ~ min. panel width, 100 mm (3.9") and 210 mm (8.2") min. length.Equipped with: -- Automatic coil & strip feed magazine, with Heavy Duty 3 mm PVC cap. guillotine. -- Gluing Unit, Teflon coated quick change glue tank, approx. 10-minute heat-up time, programmable temperature control w/timer if machine idles to prevent glue overheating/burning. -- Side Pressure Unit: 3-roll pressure unit w/1st roller power driven via clutch with pneumatic in & out positioning, (2) idler rollers.Workstations: -- Pre-Milling Unit: (2) 2.0 HP (1.5 kW) motors, to rectify/clean panels already sized. -- End Trimming Unit:Front & rear end trim (2 x 0.3 HP - 12,000 RPM motor ea.), with pneumatic tilting (0° - 15°). -- Top & Bottom Trimming Unit: Combination flush/bevel/radius trimming (2 x 0.65 HP - 12,000 RPM ea. motor), with pneumatic tilting from 0 - 25°. -- Corner Rounding Unit: 2-Motor Corner Rounding unit for leading & trailing edges. -- Edge Scraping Unit: Top & Bottom PVC Scraper for up to 3 mm radius, complete with 3 mm scrape shaving collection box. Programmable, pneumatic exclusion on/off. -- Buffing Unit:Top & bottom buffing unit (2 x 0.2 HP - 1,400 RPM motor each), Tilting range 8°Controller: -- "MEGA 200":Sequential motor start, 6" color monitor, up to 100 programs capacity, maintenance alarms & machine use statistics.Complete With:- Electronic positioning of upper pressure beam- Pneumatic exclusion of trimming unit and edge scraping unit- Track Drive Chain feed speed 12 MPM (39 FPM) - (2) rows of upper pressure wheels in hold-down beam.- Adjustable material support outrigger.- Sound & Safety Hoods- Used Tooling -- Actual Model is CASADEI FLEXA 208-MA-8NOTE: Pictured Dust Collector & Return Conveyor is not included.

CASADEI FLEXA 37 RMAT-7 EDGEBANDER (W/PRE-MILL & CORNER ROUNDING): -- Specifications: 0.4 mm - 3 mm Max. edge thickness cap., (0.5 mm to 3 mm for solid strip edge thickness). 8 mm - 50 mm (0.3" - 1.97") panel thickness cap. (when edgebanding 3 mm PVC max. thickness is 40 mm). -- Minimum panel dimensions 80 mm wide x 140 mm long (3.15" x 5.5"). -- Automatic feed of coil banding and semi-automatic strip fed magazine (strips 1- 3 mm max.) with 3 mm PVC cap. guillotine.Equipped with: -- Teflon coated glue pot w/fast (10 - 12) Min heat-up time; 1 Kg. capacity. -- Guillotine to cut edgebanding in coils up to 3 mm thick. -- Pneumatically controlled pressure section with (3) pressure rollers; 1st drive, (2) idle.Workstations: -- Cutting group moves on rounded ways made of hardened steel, to guarantee high precision and reliability; cutting movement from the top of the panel is synchronized by the PLC control. -- Pre milling unit with 3 HP - 8,300 RPM High Frequency motors. -- Double motor end trimming saw unit with (2) 0.25 HP - 12,000 RPM High Frequency motor. -- Top & Bottom Trim station with (2) 0.45 HP - 12,000 RPM High Frequency motors; unit features adjustable copying on vertical & horizontal floating movements, adjustable cutter-head position by mechanical digital readouts, quick release (electrical & mechanical). -- Single motor Corner Round Unit (set up for 3mm). -- Top & Bottom 3 mm scrape station -- Top & Bottom Buffing unit with (2) 0.20 HP - 1,400 RPM motors. -- Fixed feed speed 23 FPM. -- Actual Model is CASADEI FLEXA 37 RMAT-7

CASTALY MAX370P EDGEBANDER WITH PRE-MILLING AND CORNER ROUNDING0.4 - 3 mm Edge thickness, panel thickness 8~45 mm, min. panel width 100 mm (4″), min. panel length 170 mm (6.7″).Equipped with: -- Quick melt Teflon coated glue pot 2.5 Lbs capacity. Two spring-loaded pressure rollers (One driven, one idling).Automatic coil feed PVC/ABS up to 3mm thick, pneumatically operated guillotine. Laminate strip material can be hand-fed.PLC control system with LED display and keypadWork stations: -- Pre-Mill station with (2) 1.1 Kw 12,000 RPM trim motors 32 mm (1.25") max. material thickness. -- Single motor front and rear edge trim station. -- Top & bottom trim station with insert knife cutters for radius trimming & bevel trimming. -- Corner Rounding Unit for leading and trailing corners with (1) 0.5 HP (0.37 kW) - 12,000 RPM motor. -- Top & bottom scrape station 2 mm radius. -- Top & bottom buffing. -- Feed speed 29 FPM

CEHISA PRO-9 EDGEBANDER SINGLE PHASE ELECTRICAL!Single sided edgebander with end trim, top/bottom trimming, scraping and buffingSpecifications: -- 0.4 - 3 mm Edge thickness cap., -- Teflon coated glue pot system, -- Automatic magazine for strip & coil feed; Heavy Duty guillotine for up to 3 mm thick PVC, -- (2) roll pressure zone with (1) motorized and (1) idle roller. Workstations: -- Double motor end trim station (0.33 HP - 12,000 RPM motor ea ); -- Top & bottom flush/bevel trim, bevels 0° - 20° (0.45 HP motor ea.) -- Top & bottom PVC profile scraper for up to 3 mm radius. -- Last Station: Top & bottom buffing unit (0.75 HP motors). -- Electronic braking on trim motors; digital readout on top/bottom trim. -- Feed speed of 33 FPM & 1 HP feed drive. -- - Sound enclosure, -- Outboard panel support, -- Frequency converter, -- Digital readouts for trimmer adjustments, -- Sound enclosure

CEHISA - PRO 10, ...EDGEBANDER (W/PREMILL): -- Features: Premilling Station with: 2 x 1.5 kW (2.0 HP) 12,000 RPM motors; standard equipped with diamond cutters. Both spindles pneumatically controlled. -- Automatic Edge Magazine: For coiled material up to 3 mm thickness, strip feed magazine for up to 5 mm (3/16") solid wood banding. -- Quick Melt Glue System: 10 - 15 Min. heat up time, auto-temperature drop. Glue Tank is coated with nonstick material, quick change mechanism for easy maintenance and/or color change. -- Pressure Section: (1) Large dia. driven and (2) idle rollers. Digital readout and pneumatic positioning selectable from controller touchscreen. -- Edgebanding Workstations. End Trimming Station: Double motor front & rear, 2 x 0.35 kW (0.5 HP) - 12,000 RPM. -- Edge Trimming Station: Top & bottom flush/bevel/radius trimming, (2) 0.35 kW (0.5 HP) - 12,000 RPM motors, tiltable 0° - 20°, pneumatic exclusion from operator panel. -- Profile Scraping Unit: For thick PVC/ABS radius scraping, pneumatic in/out positioning from control panel with chip collection box. -- Flat Glue Scraper: To remove potential glue squeeze out. -- Buffing Unit: Top/Bottom, (2) 0.12 kW (1/8 HP) - 1,650 RPM motors, tilting horizontally and vertically. -- Controller: "Unitronics V350" Controller with color touchscreen, memory up to (20) programs. -- Equipped with: Feed Speed: 9 & 14 MPM (29 & 46 FPM). -- Power holddown beam, workpiece support outrigger, safety & sound enclosure. -- Included Options:RIEPE non-stick Spray System. -- Actual Model is: CEHISA PRO 10

--AT AUCTION-- COMEVA CUBE 3 Compact Edgebander, Single-Phase, Showroom Model – New, with Warranty! The CUBE 3 from COMEVA is designed to be a very compact "every day" Edgebander. The CUBE 3 Edgebander is operated through a PLC control system with a touchscreen. The machine handles panel thicknesses of 0.315" up to 1.77" (8 mm to 45 mm), The coil feed accepts Edgebanding from 0.4 mm to 2 mm thick; strip material can be hand-fed.