TWIN FLOW Air Make-Up Unit 14,000 CFM. Vertical mount with Remote Control Panel: -- CFM: 14,000 CFM @ 1.75" ESP, 10 HPTEFC motor -- BTU: 1.38 MBTUH -- Burner: MAXON burner -- Temperature Control: 80º F temperature rise in spray cycle -- -- Mounting: Vertical, outdoor/indoor mounted -- Fuel required: Natural gas, 0.3 PSI pressure -- Intake/Discharge: Vertical, screened, air intake with vertical discharge -- Filter Sections: V-Bank style with 1’’ cleanable air intake disposable type filters -- Gas Control: Control cabinet and pre-piped gas combustion system mounted on burner section to FM, Electronic Modulation -- Specifications includes: Digital Temperature Controller, ON/OFF & Summer/Winter Switch, pressure regulator, metering valve, pilot pressure regulator & pilot gas valve, flame rod, high limit switch, air flow switch, power transformer, ignition transformer and spark plug -- Electrical Control cabinet includes: main breaker disconnects, magnetic motor starters with adjustable overload protection for air makeup, motor fuse protection -- Enclosure Design: Framed, with 18 ga. metal walls and 1" insulation -- Note: Available in Horizontal and Vertical mount. Please inquire. -- Also available: Controls option: - Two stages for 14,000 or 7,000 CFM at extra cost of about $3,000.

TYLER 804 Air Pod Press; Overall Platen dimension of 50" x 100", with (4) individually controlled top platens - each 25" X 50". -- Side loading on 100" side. -- 0 - 50" Motorized adjustable daylight. -- Pneumatic top pressure via 5-1/2" stroke air pods by (32) 8" Air Pods with maximum 50 PSI specific pressure. -- Spring loaded rollers in bottom platen for easy loading & unloading of stack.Overall Dimensions - 122" Long x 60" Wide x 97" High

TYLER "POWER POD" Cold Press with Motorized OpeningThis TYLER "Power Pod" Press has a 36″ X 148″ capacity, side loading on 148" -- It consists of (3) individual top mounted platens with their own controls that measure 36"; wide x 49"; long each. There are a total of (27) total air pods or (9) for each platen. -- 3-1/2″- 48″ adjustable motorized daylight opening. -- The bottom platen has spring loaded rollers for easy loading and unloading. -- Max. operating pressure is 100PSI.NEW plumbing, NEW regulator, a few NEW air bags, NEW top plates, and fully cleaned and tested.

--In Auction--- TYLER French-Type Dovetail Machine Equipped with: - (2) 14-1/2” x 17” Tables. - (2) 2 HP Routing heads for mounting of drawer sides. - (1) 2 HP Grooving head for drawer bottom dado, - (2) 2-Spindle Vertical boring heads for drawer hardware. - (2) Pneumatic hold-down clamps Details, Photos, Videos, Bidding: https://exfactoryauctions.com/Detail/DL-230110/event/A051324$1

TYLER 2400 SLOT-WALL MACHINE: -- Specifications:Produces T-slot "slat-wall" for architectural/store fixtures. 4' x 8' (48" x 97") max. panel cap., 2' x 2' (24" x 24") min. panel cap., min. panel thickness = 0.5" max. panel thickness = 1.5"; The Tyler 2400 can machine up to (40) panels/Hr, depending on material density, thickness and the slot profile. -- Equipped with: (18) Router spindles all on 3" fixed centers, spindles are driven in groups of (3) with (6) 7.5 HP - 3,450 RPM motors, all router spindles rotate @ 15,400 RPM. -- Operation: Panels remain stationary on top, pneumatically clamped in place while the bottom mounted router bank traverses the full length of the panel with a high-speed return, variable feed speed control, router assembly traverses on ground & polished rails with chain drive. -- Panels are positioned along the 8' rear edge fence line, distance from the panel edge to the centerline of the 1st cut can be adjusted from 0.0" - 3" (1 router spindle pitch). -- Overhead hold-down assembly with (2) large air cylinders and (5) arms with spring loaded clamping pads hold the panel in place. Panels are loaded from the 8' front and exit to the side. -- Includes: Operator controls for the machine cycle and a "setup" mode of operation; machine cutting cycle is initiated by a 2-hand operator safety buttons located on the right front of machine. - Produces approx. (30 - 40) panels per hour. -- Available Options at Additional Cost:Router spindles on 4'- & 100-mm centers; 48" x 121" workpiece capacity increases left-to-right workpiece (length) capacity.60" x 97" workpiece capacity increases front-to-back workpiece (width) capacity & includes (1) additional multi-spindle router head.60" x 121" workpiece capacity increases front-to-back & left-to-right workpiece capacity & includes (1) additional multi-spindle router head.

UAS FJH8-2 DUST HOG Cartridge Dust Collector with Rotary Air Lock. Approx. 3,500 CFM Cartridge Filter System, complete with capacity of 1,808 sq. ft. of filter area composed of (8) cylindrical cartridges (226 sq. ft. cloth area per cartridge), CFM based on a target 2:1 Air to Cloth Ratio.. -- Automatic Pulse Clean System with differential pressure gauge and sequencing timer board in enclosure. Continuous pulse jet cleaning via compressed air, (1) pulse valve per (2) cartridges. -- Includes: Bottom hopper ROTOLOK 8" Rotary Air Lock (not mounted and to be adapted). steel support legs. -- Features: Heavy Duty steel legs which can be extended for position a storage container below RAL's. -- Comes with: CINCINNATI 150 BI t0 HP side mounted direct drive fan motor which pulls dust laden air thru the collector (clean air side); Baghouse has dusty air inlet at the top of hopper and clean air discharge from fan. -- Price includes dismantling and loading on flatbed truck.

ULTRA GL-630H Feed Through Moulder: 6-Head (B-T-R/L-T-B), "Flooring" working capacity of 12" x 6".Specifications: -- Head sequence: Bottom 25 HP, top 30 HP, right 20 HP/left 20 HP (opposing), top 25 HP, and bottom 25 HP motor. -- Spindle dia. of 1-13/16" with cutterhead speed of 6,000 RPM; all spindles with high prevision bearings. -- Auto. positioning of the left & top spindles radially; all additional spindles with digital readouts, including chipbreaker & pressure elements. -- Pneumatics on all chipbreakers, pressure elements, and holddown rollers. -- Horizontal spindles with HydroLock outboard bearings on #1, #2, #5 & #6. -- Straight jointer on spindles #5 & #6; Profile Jointers on spindles #3, #4, #5 & #6. Equipped with: -- Inverter controlled feed drive, variable speed of 26 - 260 FPM. -- Infeed table 1.2 M (4') with all table plates & fences hard chromed to RC 70. -- Machine table includes: (5) Table rollers for smooth through feed; short stick attachment for through feed on pieces down to 230 mm. -- Electrical cabinet & pedestal for machine controls separate from machine, Heavy Duty sound enclosure. -- Includes Startup training and Warranty!

UNIQUE - 313, ...Automatic Cope & Dowel Door MachineMiters the end & drills for dowels of (2) cabinet door rails on each pass; automatic cycle for accurate & easy alignment of mitered corners.Equipped with: -- (2) 5 HP Dual motor set for shaping w/1-1/4" spindles; (2) 0.33 HP dowel alignment drills. -- Automatic cycle with: Dowel hole boring for accurate alignment of mitered door corners in (15) Sec/cycle. -- 1" Material thickness cap., 4" max. material width, 5" max. cutter diameter. Features: -- (2) Pneumatic clamps hold material during operation for safe machining of parts; adjustable stops for dowel drilling; air over oil rodless cylinder driven table. -- Staggered tables with angled fences allow: (2) 1" Thick parts to be machined simultaneously; digital position indicator. -- Dust Collection: (2) 5" Dust ports require approx. 1,000 CFM per spindle.

UNIQUE 2753 Arch Shaper with Sanding HeadThe Unique Model 2753 Is A Single End Machine Designed For High Quality, High Production, Cabinet And Passage Door Arching Of Top Rails And Panels. Its Two Counter-Rotating Spindle Motors are Easily Programmed For Multiple Cuts With Hogging And Finishing Cutters To Eliminate Tear-Our And Extend Tool Life. A Sanding Station Provides A Multi-Pass Sanding Finish On Arched Door Panel Profiles. Unique “ArchPro"; Software Guarantees High-Speed Measuring And Fully Dynamic Programming Abilities.• Shaper Motor: (2) 10 HP Himmel Direct Drive , 440V - 39.2A, 3PH Motor• 5" Stack Height • Compressed Air Requirements: 90 PSI - 2 CFM• Dust Collection: (2) 5" Diameter 1200 CFM each (1) 4" Diameter 800 CFM each• Work Height: 3’6"• Machine Footprint: 113" Width X 78" DepthIncludes - Safety Mats, Dust Collection Manifold, and Owner's Manual

UNIQUE 250 GT2 Automatic Raised Panel Door ShaperMachine to manufacture raised panel cabinet doors with (1) operator in (2) Min.Specifications: -- Two Counter-Rotating Variable Speed Direct Drive 10 HP Shaper Motors. -- 5" of vertical stack height, capable of stacking up to (3) cutters. -- Three (3) Position Turret for quick change over between profiles. -- The change from one cutter to another is achieved via a select switch for each operation. -- Two-position pneumatic stop system positions automatically when cutters are selected -- Easy to read positioning scale allows for accurate centering of Arched panel and rail. -- Free-floating table w/pneumatic holddown has a 2-way linear movement for straight or cathedral top doors up to 55" long.Complete with: -- (1) Set of templates (998800). -- One set of tooling included. Set includes Unique 410 cope / rail cutters and 460 panel cutter with back cutter. -- Please call for other options.

UNIQUE 2700 CNC CNC Door ShaperCNC Controlled Machining Center for Raised Panel Doors.Equipped with: -- (1) CNC controlled 5" stackable vertical spindle (max. 4 tools per stack), 7.5 HP belt driven; max. clamping thickness 2-1/2" and 6" max. cutter head diameter. -- "X" Axis of spindle travels 81" on (2) THK rails with ball screw movement, "Y" axis with 5" travel on THK rails with 5" max. workpiece overhang, "Z" axis with 5" max. travel on THK rails.Features: -- Windows based PC computer with large touch screen menu for quick set-up, new door or custom door stiles can be programed in minutes, automatic operation from one style and size of door to the next, straight raised panels & widths of stile or rail and end tenoning work the same. -- Electronic sensors measure the length of the part to be cut allowing for various width panels or rails to be shaped consecutively, once a door is pre-programmed it can be re-called.Complete with: Electronic brake on spindles, (2) 5" dia. outlets for dust collection and UNIQUE's Windows based "Raised Panel Door" Software. .

UNIQUE 4522 Shape and Sand with DOUCET Return Conveyor(4) Stations (2 Floating shapers, 2 floating sanders), each with 5" stack capacity.Configured as follows:(2) Shaper Stations with: 10 HP Direct drive HIMMEL motors, 1-1/4" dia. arbors.(2) Sanding Stations with: 2 HP Direct drive BALDOR Motors, 1" dia. arbors tiltable up to 45 °.Sanding Stations are variable speed from 6,000 - 9,000 RPM and reversible.Shaper Stations are variable speed from 6,000 to 9,000 RPM and reversible.Specifications & Features:Variable speed conveyor speed from 0 - 35 FPM; 6"Heavy Duty conveyor and roller hold-down system.Features: Digital indicators for both horizontal & vertical adjustment on all spindles from the front.PLC Controlled "jump-cope"; machine is equipped with Windows/XP-based computer touch-screen & software. - Software stores feed rates, positions, cutter rotation, profile pictures, and RPM settings.Includes "DRO" Option: (Software and hardware upgrade from standard "Trueset" software - linear encoders on each station send real-time location of spindle back to the computer and give the operator the desired position; Machine will not start until all spindles are manually brought to the correct setting; a ...$ 10,950 value option).Includes Optional "Inset" automated size &squaring infeed fence ($ 16,850.00 option value).Max. material thickness - 2-1/2"; min. material width - 1-1/2" plus the depth of the cut.(2) 5" Dia. dust ports and (2) 4" dia. dust ports; Tooling not included.Complete with: DOUCET Feedback Return Conveyor ($ 10,000 option value).Floorspace required with DOUCET Return is 17-1/2' x 10'.

UNIQUE 313 Automatic Cope and Dowel Door MachineMiters the end and drills for dowels of (2) cabinet door rails on each pass, automatic cycle for accurate & easy alignment of mitered corners.Equipped with: -- (2) 5 HP Dual-motor set for shaping w/1-1/4" spindles; (2) 1/3 HP dowel alignment drills. -- Automatic cycle with dowel hole boring for accurate alignment of mitered door corners in (15) Seconds per cycle, -- 1" Material thickness capacity, 4" max. material width, 5" max. cutter diameter. Features: -- (2) Pneumatic clamps holds material during operation for safe machining of parts, Adjustable stops for dowel drilling, Air over oil rod-less cylinder driven table. -- Staggered tables with angled fences allow (2) 1" thick parts to be machined simultaneously; digital position indicator. -- Dust Collection: (2) 5" Dust ports require approx. 1,000 CFM per spindle.Includes - Standard Finger joint shaper heads to cut miters and drill bits for doweling.

UNIQUE - 2700 CNC, ...CNC Door ShaperCNC Controlled Machining Center for Raised Panel Doors.Equipped with: -- (1) CNC Controlled 5" stackable vertical spindle, max. (4) tools per stack; 7.5 HP belt driven; max. clamping thickness: 2-1/2" & 6" Max. cutter head diameter. -- X-Axis of spindle travels 81" on (2) THK rails with ball screw movement; Y-axis with 5" travel on THK rails with 5" max. workpiece overhang; Z-axis with 5" max. travel on THK rails.This machine is designed to perform the following: -- Arched panels (from DXF file) -- Arched rails (from DXF file) -- Mitered Tenons (w/ holes for dowels) -- Straight Tenons (w/ holes for dowels) -- Rounded Tenons (w/ holes for dowels) -- Straight Rail CutFeatures: -- Windows-based PC with large touchscreen menu for quick setup; new door or custom door stiles can be programed in minutes; automatic operation from one style & size of door to the next; straight raised panels & widths of stile or rail; end tenoning work the same. -- Electronic sensors measure the length of the part to be cut allowing for various width panels or rails to be shaped consecutively; once a door is preprogrammed it can be recalled.Complete with: Electronic brake on spindles; (2) 5" dia. outlets for dust collection.

100HP Single Shaft Shredder With Infeed and Discharge ConveyorsSpecifications: --100 HP --Includes Infeed Conveyor- 50" Wide x 37’6"; Long, Sides 20"; high --Includes Discharge Conveyor - 47" Wide x 16' Long

12-Station Paint Colorant Dispenser with Unused CupsDimensions: 24" x 24" x 24" H.

---In Auction---NO RESERVE--- 2-Spindle Vertical Boring Machine Equipped with: - 1 HP - 3,400 RPM Motor. Complete with: - "30C-W20” 2-Spindle Boring Head, with Maximum bit cap. 15 mm (0.59”), Bit threads 7/16 - 14 TPI Right-hand, Spindle speed 4,000 RPM Details, Photos, Videos, Bidding: https://exfactoryauctions.com/Detail/BV-230384/event/A051324$1

---In Auction---NO RESERVE---Fair Condition--- 7' Stroke Sander Specifications: - Table size 19” x 73-1/4” x 24” H, with 19-3/4” x 73-1/4” x 3/4” Thick Wood top. - Manual table stroke 26-3/4". Equipped with: - 7” W x 84” Face Sanding belt, with 3 HP - 1,140 RPM Motor. Details, Photos, Bidding: https://exfactoryauctions.com/Detail/SS-230670/event/A051324$1

---In Auction---Good Condition--- 24" 2-Head Wide Belt Sander Specifications: - Thickness cap. 0" - 5". Equipped with: - 1st Head: 5” Dia. Grooved rubber-covered contact roll, with 15 HP - 1,740 RPM Motor. - 2nd Head: 3” Dia. Grooved rubber-covered & 3” Dia. Smooth steel contact rolls, with Finishing platen, & 15 HP - 1,740 RPM Motor. - 1-1/2” Dia. Spring-loaded rubber-covered infeed & outfeed pinch rolls, (1) In front of 1st head, (1) In between heads, & (2) Pair after 2nd head. - 23-1/4” W x 3-1/2’ L Feed belt, with 2 HP - 1,720 RPM Motor. Control, with Motor load meters. Details, Photos, Bidding: https://exfactoryauctions.com/Detail/SX-230385/event/A051324$1

Steel Belt CP Conveyor - 72" Wide Above or In-Ground Specifications: -- Steel Belt Width: 72" -- Lower horizontal length: 20' -- Incline section length: 22' -- Nose over: 2' - 4'