BLACK BROTHERS - 22-D-875-56, ...Roller Coater56" Nominal length; 8-3/4" dia. applicator, Chrome doctor roll, upper elevator & top only. -- Setup to 0" - 6" thick. -- Smooth Chrome applicator rolls and Chrome doctor rolls. -- Stationary feed speed drive, passline height 34". -- Drip Pan, Feed Pan, Continuous Flow Through. -- Trough for continuous flow 1" pneumatic pump and hose to supply product. -- (30) Day warranty for workmanship and manufacture's warranty for all parts used.Complete with: -- NEMA-12 Electrical enclosure, operating control bars, magnetic brake, electrical interlocks, reverse lockout, and cleanup pan.

BLACK BROTHERS - 22-D-875-56, ...Roller Coater56" Nominal length; 8-3/4" dia. applicator, Chrome doctor roll, upper elevator and top only. -- Setup to 0" - 6" thick. -- Smooth EPDM applicator rolls and Chrome doctor rolls. -- Variable feed speed drive, pass line height 34". -- Drip Pan, Feed Pan, Continuous Flow Trough to be Stainless Steel or Teflon Coated. -- Trough for continuous flow 1" pneumatic pump and hose to supply product.Complete With: -- NEMA-12 Electrical enclosure, operating control bars, magnetic brake, electrical interlocks, reverse lockout and cleanup pan.

BLACK BROTHERS - 410-56: Panel Brush Cleaner56"+ Top & Bottom Panel Cleaner; upper elevator: 0" to 4-3/4" upper elevator opening; standard: 30" passline height. -- (2) New 61-1/2"; wide (max. brush width) fiber brush rolls. -- 3 HP Speed drive; 230 /460 V/3-phase motor voltage; currently wired for: 230 Volt / 3-phase power. -- Feed speed approx. 80 FPM -- (2) 3-1/2" Upper infeed & outfeed spring loaded idler rollers; (2) 3-1/2" lower infeed & outfeed feed rollers. -- Operating handwheel & magnetic starter: Located on left-hand side. -- Complete with: Sheet metal hood w/separate (2) exhaust ducts for upper & lower cleaning brushes; requires 2,800 CFM. Machine was refurbished & never put into production. Cleaned & checked: "New" brushes; "new" feed rollers; (3) spare feed rollers; fresh paint.

BURKLE - VBM 1688, ...Stain Wiping MachineSingle sided machine, 1,600 mm wide; 2-Brush Panel Cleaner (TAMPICO brushes). Features: Heads can be positioned as needed spacing between the brushes by sliding brackets. Brush raising & lowering accomplished by means of handwheel adjustment. Brushes are removed at side of machine by sliding out of shroud/channel support rail. Safety bar checks part thickness for overthickness parts. SIEMENS Control to set rotation speeds & feed belt speed. Rigid Aluminum bolted base construction. Solid feed belt (NO vacuum holddown)

Features:• Top quality resin conveyor belt ensures minimum stretch and long service life.• Fast cleaning of the resin conveyor belt, and easy belt tracking with the hand knob.• Infinitely variable conveyor feed rate 40 - 100 meters per minute suited for desired coating thickness.• Paint material is delivered through the powerful pump unit running low noise.• Flow of paint can be infinitely regulated to any amount desired, will circulate back to the pump unit without any loss of paint.• Open type coating device, easy to clean interior and installed clear windshields keep wind away in coating processes.• Simple operation, low cost for maintenance & service the coating material can be circulated and no waste.• Rapid for coating speed, the feeding variable speed can be adjusted from 80 FPM ~ 260 FPM randomly advanced operating efficiency.• Heavy-duty construction for long-life usage.SPECIFICATIONS: TS-1200FX Max. Coating Width - 50" Max. Coating Thickness - 1/8" Minimum Coating Length - 7" Throat Clearance Range - 0 -1/16" Feed Speed (Variable) - (FPM) 80 ~ 260 Material Container - 20 L Circulating Pump Hose - 1" Conveyor Belt Motor - 2 HP Pump Motor - 1 HP N.W. - 2640 LBS G.W. - 3300 LBS (Customer is responsible for local regulations and connecting utilities)

TS-24ATSM:Features:• Through feed conveyor with cleaning brush for the belt, no minimum length limitation.• PLC control for easy operator and variability setup.• Fast spraying processing for profile strips and two edges in one pass through the machine.• Spray gun "On/OFF" controlled by photocell sensor for automatic spray control saving the spray material.• Individual coating volume adjustment control for each spray gun.• Variable feed speed control for the best finish results.• Two collection trays to catch overspray. • Powerful collection fan for air filtration by dry filter in totally enclosed cabinet eliminating no spray or fumes in the air.• Heavy sheet metal total enclosure frames and see through cabinet window.• Standard equipment comes with (1) one pneumatic paint pump and (4) four spay guns.• Extra spray guns are optional additional cost.SPECIFICATIONS: Max. Working Width - 12" Max. Working Thickness - 3-1/2" Max. Working Length - Infinite Min. Working Length - 19" Conveyor Feed Motor - ½ HP Feed Speed (Variable) - 32 ~ 96 FPM Spray Gun Capacity and included - 4 Paint Pump (piston type) included - 1 Set Exhaust Fan Motor - 3 HP Machine Size (L x W x H) - 138" x 62" x 99" Net Weight - 3200 LBS (Customer is responsible for local regulations and connecting utilities)

TS-24ATSPX:Features:• Through feed conveyor with cleaning brush for the belt, no minimum length limitation.• PLC control for easy operator and variability setup.• Fast spraying processing for profile strips and two edges in one pass through the machine.• Spray gun "On/OFF" controlled by photocell sensor for automatic spray control saving the spray material.• Individual coating volume adjustment control for each spray gun.• Variable feed speed control for the best finish results.• Two collection trays to catch overspray. • Powerful collection fan for air filtration by dry filter in totally enclosed cabinet eliminating no spray or fumes in the air.• Heavy sheet metal total enclosure frames and see through cabinet window.• Standard equipment comes with (1) one pneumatic paint pump and (4) four spay guns.• Extra spray guns are optional additional cost.SPECIFICATIONS: Max. Working Width - 24" Max. Working Thickness - 3-1/2" Max. Working Length - Infinite Min. Working Length - 21.5" Conveyor Feed Motor - ½ HP Feed Speed (Variable) - 32 ~ 96 FPM Spray Gun Capacity and included - 6 Paint Pump (piston style) included - 1 Set Exhaust Fan Motor - 5 HP Machine Size (L x W x H) - 138" x 73" x 78" Net Weight - 3960 LBS (Customer is responsible for local regulations and connecting utilities)

Features:• Top quality resin conveyor belt ensures minimum stretch and long service life.• Fast cleaning of the resin conveyor belt, and easy belt tracking with the hand knob.• Infinitely variable conveyor feed rate 40 - 100 meters per minute suited for desired coating thickness.• Paint material is delivered through the powerful pump unit running low noise.• Flow of paint can be infinitely regulated to any amount desired, will circulate back to the pump unit without any loss of paint.• Open type coating device, easy to clean interior and installed clear windshields keep wind away in coating processes.• Simple operation, low cost for maintenance & service the coating material can be circulated and no waste.• Rapid for coating speed, the feeding variable speed can be adjusted from 80 FPM ~ 260 FPM randomly advanced operating efficiency.• Heavy-duty construction for long-life usage.SPECIFICATIONS: TS-300F Max. Coating Width - 12" Max. Coating Thickness - 1/8" Minimum Coating Length - 7" Throat Clearance Range - 0 -1/16" Feed Speed (Variable) - (FPM) 80 ~ 260 Material Container - 20 L Circulating Pump Hose - 3/4" Conveyor Belt Motor - 1 HP Pump Motor - 1/2 HP N.W. - 1320 Lbs G.W. - 1650 LBS (Customer is responsible for local regulations and connecting utilities)

Features:• Top quality resin conveyor belt ensures minimum stretch and long service life.• Fast cleaning of the resin conveyor belt, and easy belt tracking with the hand knob.• Infinitely variable conveyor feed rate 40 - 100 meters per minute suited for desired coating thickness.• Paint material is delivered through the powerful pump unit running low noise.• Flow of paint can be infinitely regulated to any amount desired, will circulate back to the pump unit without any loss of paint.• Open type coating device, easy to clean interior and installed clear windshields keep wind away in coating processes.• Simple operation, low cost for maintenance & service the coating material can be circulated and no waste.• Rapid for coating speed, the feeding variable speed can be adjusted from 80 FPM ~ 260 FPM randomly advanced operating efficiency.• Heavy-duty construction for long-life usage.SPECIFICATIONS: TS-750FX Max. Coating Width - 30" Max. Coating Thickness - 1/8" Minimum Coating Length - 7" Throat Clearance Range - 0 -1/16" Feed Speed (Variable) - (FPM) 80 ~ 260 Material Container - 20 L Circulating Pump Hose - 1" Conveyor Belt Motor - 2 HP Pump Motor - 1 HP N.W. - 2090 LBS G.W. - 2530 LBS (Customer is responsible for local regulations and connecting utilities)

Features:• Top quality resin conveyor belt ensures minimum stretch and long service life.• Fast cleaning of the resin conveyor belt, and easy belt tracking with the hand knob.• Infinitely variable conveyor feed rate 40 - 100 meters per minute suited for desired coating thickness.• Paint material is delivered through the powerful pump unit running low noise.• Flow of paint can be infinitely regulated to any amount desired, will circulate back to the pump unit without any loss of paint.• Open type coating device, easy to clean interior and installed clear windshields keep wind away in coating processes.• Simple operation, low cost for maintenance & service the coating material can be circulated and no waste.• Rapid for coating speed, the feeding variable speed can be adjusted from 80 FPM ~ 260 FPM randomly advanced operating efficiency.• Heavy-duty construction for long-life usage.SPECIFICATIONS: TS-990FX Max. Coating Width - 36" Max. Coating Thickness - 1/8" Minimum Coating Length - 7" Throat Clearance Range - 0 -1/16" Feed Speed (Variable) - (FPM) 80 ~ 260 Material Container - 20 L Circulating Pump Hose - 1" Conveyor Belt Motor - 2 HP Pump Motor - 1 HP N.W. - 2490 LBS G.W. - 2970 LBS (Customer is responsible for local regulations and connecting utilities)

CEFLA 5 Ft. Wide Single Lamp UV OvenGreat for handing those "extra wide" Panels!Features: -- UV-R Super Focus: This configuration is suitable for reducing the heating effect of the lamps on artifacts sensitive to high temperatures (e.g. resinous wood). -- The particular shape of the lamp parabolas focuses the UV ray beam at the same point of the panel, allowing to reduce significantly reducing the number of lamps needed to dry the paint and avoiding the dispersion of rays, also guaranteeing significant savings in terms of space and energy consumption. -- This configuration can be integrated with the "SMART-THICK" system for adjusting the thickness of the pieces in line, usually on roller application lines.UV-R SP: Allows the cross-linking of the paint applied even on the edges of the pieces, thanks to the use of inclined lamps and a greater energy impact of the lamps themselves on the edges.UV-R: Equipped with an electronic system for regulating the power of each lamp; it also allows you to automatically activate the energy-saving function by checking the presence of material under each lamp.The Electrical Panel is integrated into the machine body and does not require additional spaces in the line layout.

2019 CEFLA, model ROC 3 D. Reciprocating Spray Machine:This sprayer can easily run at 30 feet per minute Machine consists of --a tilt-able up infeed belt conveyor with the Electronic Reading bar located over the entire width, this bar reads the parts as they enter the machine which controls the Gun spray pattern. --Parts are fed through the spray cabin by means of a Patented continuous CFB belt conveying system. --Sprayer is equipped with (2) two roll Overspray recovery systems. Belt cleaning is done by means of a counter-rotating roller's with scraper and belt cleaning unit. The rollers are fitted on the "cleaning" trolley which is pulled out from under the machine longitudinally by manual control. Motorized outfeed belt conveyor, tilt-able up to make access to the cleaning trolley easy. -- (2) Oscillating arms equipped to accept a maximum of (8) guns, driven by a Brushless motor's, the PLC in the control panel automatically triggers the guns based on thier size and location on the belt. -- This sprayer has (2) two separate lacquer feeding circuits and a pressurized cabin with both incoming air filtration and exhaust filtration. -- Air is pulled in from (2) air intake ducts (positioned between guns) above the slanted perforated top panels, perforations help to reduce turbulence -- Large front viewing window/access panel.

CEFLA ROCTRE D Automatic Spray Finishing Machine for HIGH VOLUME PRODUCTION and includes (2) two integrated cleaning trolleysThickness: Max. 50 mm (2"); Min. 5 mm (0.2").Maximum Line speed: 20 MPM (65 FMP).Equipment Specifications:CEFLA, model ROC 3 D. Is a Two-arm reciprocating Spray Machine: -- Parts are fed under the Part Reading Bar to measure size and spray parameters on a continuous CFB belt conveying system. -- Lacquer recovery and belt cleaning are accomplished by means of a "cleaning trolley" located under the existing end feed belt. Made up of counter-rotating rollers with scraper and belt cleaning unit, with (3) rollers and stainless-steel troughs: all the rollers are fitted on the motorized trolley longitudinally removable by hand pulling of trolley out. -- Powered outfeed tilt-able belt lifts to approach the cleaning trolley. -- (2) Oscillating arms equipped to accept a maximum of (8) guns, four per arm, and driven by a Brushless servo motor.There are (2) Separate lacquer feeding circuits with recycling system. -- This is a fully pressurized spray cabin with an exhaust air filtering system for overspray using a double dry filter set, primary filter, and secondary. -- Electronic control cabinet to monitor spraying functions.The booth consists of sandwich paneling, and air is pushed in through (2) air intake ducts (positioned between guns) above the slanted perforated top panels made of fine filter material, which help to reduce turbulence. Parts running through the sprayer can be viewed by means of a large front viewing window/access panel, which can be lifted to access the guns and interior of the sprayer. Photos show equipment while it was still in service - currently being reconditioned.Note: EX-FACTORY’s Logistics Department is experienced and set up to provide “Full Service Logistics"; from Overseas Suppliers to your Door. …Packaging, Container Loading, Ocean Freight, Marine Insurance (door to door).

CEFLA ROCTRE D Automatic Spray Finishing Machine: for HIGH VOLUME PRODUCTIONThickness: Max. 50 mm (2"); Min. 5 mm (0.2").Maximum Line speed: 20 MPM (65 FMP).Equipment Specifications:CEFLA, model ROC 3 D. Is a Two Arm reciprocating Spray Machine: -- Parts are fed under the Part Reading Bar to measure size and spray parameters on a continuous CFB belt conveying system. -- Lacquer recovery and belt cleaning are accomplished by means of a "cleaning trolley" located under the exist end feed belt. Made up of counter-rotating rollers with scraper and belt cleaning unit, with 3 rollers and stainless-steel troughs: all the rollers are fitted on the motorized trolley longitudinally removable by hand pulling of trolley out. -- Powered outfeed tilt able belt lifts to approach the cleaning trolley. -- (2) Oscillating arms equipped to accept a maximum of (8) guns, four per arm and driven by a Brushless servo motor.There are (2) Separate lacquer feeding circuits with recycling system. -- This is a fully pressurized spray cabin with an exhaust air filtering system for overspray using double dry filters set, primary filter and secondary . -- Electronic control cabinet to monitor spraying functions.Booth consists of sandwich paneling and air is pushed in through (2) air intake ducts (positioned between guns) above the slanted perforated top panels made up of fine filter material help to reduce turbulence. parts running through the sprayer can be viewed by means of a large front viewing window/access panel which can be lifted to access the guns and interior of the sprayer. Note: EX-FACTORY’s Logistic Department is experienced and set up to provide “Full Service Logistic"; from Overseas Suppliers to your Door. …Packaging, Container Loading, Ocean Freight, Marine Insurance (door to door), US or Canadian Customs, Duty and domestic shipping to your Plant Door.

CEFLA "ROTOSTAIN RT 2000 10 + 10 Rotary Stain Machine with: -- 20 Guns; utilized for automatic application of stain material on workpieces; the "Roto-Stain ROT 10 + 10" represents a new generation Spray Machine from CEFLA, the leader in CEFLA "ROTOSTAIN RT 2000 10 + 10 Rotary Stain Machine with: -- 20 Guns; utilized for automatic application of stain material on workpieces; the "Roto-Stain 2000 10 + 10" represents a new generation Spray Machine from CEFLA, the leader in technology development for spraying applications. -- The "Roto-Stain 2000 10 + 10" incorporates CEFLA's previous innovative developments into a machine with maximum capabilities (line speed and production output) for stain application. -- Continuous 65" width carbon fiber belt enables the recovery of over sprayed coating material for reuse. -- Cefla's patented conveyor belt system for coating recovery and belt cleaning is controlled by the PLC and recovers approximately 98% of the coating material deposited on the belt, which is then automatically cleaned with "Coating Appropriate Solvents" -- The automatic air flow system monitors and maintains consistent air flow/pressurization through spray booth. When filters become too plugged to maintain sufficient air flow, system operation is ceased --electronic control unit utilizes a 60 cell photodiode bar to monitor and regulate spray application, further maximizing application transfer efficiency -- Spraying is performed through a rotary system designed for the installation of ten plus ten (10 + 10) guns in (2) coating supply circuits with recycle.TECHNICAL SPECIFICATIONS: Working width from 0 - 1300mm ( 0 - 51") Minimum workpiece length 305mm (12") Speed range from 2 - 11 m/min (6.6 - 36 ft/min) Power consumption 10.7 kW Compressed air required 50 NI/min (1.8 cfm) Exhausted solvent /air mix 10000 mc/h (5886 cfm)

The CEFLA Belt Handling Type TNS 4500/A is an industrial vacuum belt conveyor designed to transport, stabilize and accurately position wood panels and furniture components throughout automated finishing lines. The machine utilizes a perforated conveyor belt combined with an integrated vacuum chamber and centrifugal blower to generate continuous negative pressure, securely holding workpieces against the belt during transport. This vacuum retention system prevents movement, vibration and misalignment while components pass through sanding, painting, drying and curing operations, ensuring consistent product positioning and superior finishing quality. The conveyor operates in synchronization with adjacent production equipment through PLC control, improving production flow, minimizing manual handling and increasing the overall efficiency, reliability and safety of industrial woodfinishing operations.Machine Type: Vacuum Belt Conveyor (Belt Conveyor with Suction)• Model: TNS 4500/A• Manufacturer: Cefla Finishing• Machine Function: Automatic conveying and positioning of workpieces through finishing lines• Conveyor Type: Continuous vacuum belt conveyor• Conveyor Length: 4,500 mm• Maximum Working Width: Up to 1,300 mm• Conveyor Belt: Wear-resistant perforated conveyor belt• Vacuum Holding System: Integrated suction chamber beneath the conveyor belt• Vacuum Generation: Integrated centrifugal blower for negative pressure generation• Suction System: Continuous vacuum retention for workpiece stabilization during transport• Drive System: Geared electric motor with variable frequency drive (VFD)• Conveyor Speed: Variable, electronically synchronized with production line equipment• Control System: PLC integrated with upstream and downstream finishing equipment (NOT INCLUDED IF PURCHASED SEPARATE OF THE LINE)• Workpiece Detection: Photoelectric sensors for automatic panel detection• Machine Frame: Heavy-duty welded steel construction• Adjustable Leveling Feet• Electrical Supply: 400–480 V, 3 Phase, 50/60 Hz• Approximate Dimensions: 4.50 × 1.60 × 0.95 m• Approximate Weight: 900–1,100 kg

EFLA - BT20 SP - 1/R: Combination Differential/Filling MachineOne of the best units ever produced! -- Dual purpose machine can be utilized as:Standard differential Roll Coater for application of U.V. sealer or topcoat material. As a differential Roll Coater, the 1st application head is independently utilized for precisely controlled application.Filling Machine. For application of U.V. filling material to calibrated substrates with porous veneer. As a filling machine, both heads are utilized for application & reverse smoothing or pressing of U.V. filling material. -- Features: 2-Head, 53" width cap.1st Head: 250 mm (9-3/4") Dia. rubber coated applicator roller; (40 shore) w/separate doctor roller.2nd Head: 245 mm (9-5/8") Dia. chromium coated smoothing/reverse roller; separate chromium doctor roll: 0 - 100 mm (3-3/4") Adjustable opening (manual).HP Conveyor Drive. Variable feed speed from: 26 - 131 FPM; 1/2 HP variable RPM drive on doctor rolls; separate 3/4 HP drive on applicator & reverse rollers; 880 mm (34-1/2") working/pass through height. -- Electrical Power: 480 V - 3 Ph (3.8 kW - 7 amps). -- Includes: Wheels & rails for removal of the Line; has its own operator Control Panel. -- Plus: Pneumatic emergency lifting in case a part is misfed or too thick for the setup.NOTE: Equipment is a Brazil version of the model. all specifications should be the same, but there may be a small variation in details.

CEFLA - EASY 2000 D: Finish SystemCEFLA - Easy 2000: Reciprocating Spray Machine. 2-Arm dry filter Reciprocating Spray Machine with: (3) Independent paint circuits; allows several different coatings to all applied using the same machine with reasonably quick-change over. Parts are electronically scanned as they enter the spray cabin: To lower waste & increase spraying efficiency.Spray guns are: All electronically controlled at the "Easy lCD" interface panel.Spray Cabin. Setup with the CEFLA Recovery System. Means: No paper belt to change maintaining a "Clean" feed belt. The positively pressurized cabin helps both: Control dust & direct overspray down into the dry paper filters. Machine: Completely reconditioned with many new parts including: All belts. Air & Fluid lines. Pumps for the cleaning trolley. Filters. Wear parts.

VERY LOW HOUR MACHINE; power on 760 hours, running 554 hoursThe CEFLA MITO 2P is an automatic industrial spraying machine used to uniformly apply paints, sealers, stains, and coatings to wood panels, doors, and components in industrial manufacturing processes. -- The machine uses two oscillating arms with automatic spray guns and a photoelectric scanning system that detects each workpiece's dimensions and position to optimize application and minimize waste. Its continuous conveyor system and electronic controls ensure consistent finish quality, high productivity, and production repeatability. -- Additionally, it incorporates filtration and overspray extraction systems that enhance process efficiency and contribute to achieving high-quality surface finishes on components destined for the subsequent assembly and finishing of furniture and wood structuresMachine type: Oscillating automatic spray painting machine• Model: CEFLA MITO 2P• Manufacturer: Cefla Finishing• Application type: Water-based paints, solvent-based paints, and industrial adhesives• Spraying system: 2 automatic oscillating arms (2P)• Typical configuration: 2 arms with 4 guns per arm• Total number of guns: Up to 8 automatic guns• Effective working width: 1300 mm• Maximum workpiece thickness: 60 – 80 mm• Minimum workpiece length: 250 mm• Variable feed speed: 1 – 6 m/Min• Maximum oscillating arm speed: Up to 140 m/Min• Maximum oscillation frequency: 55 cycles/Min• High-precision photoelectric barrier scanning system• Automatic spray optimization system• Paper conveyor belt with vacuum system• Patented Airsphere Plenum system for airflow control• Overspray filtration via dual-stage dry filters• Automatic color and product change system• 12.1"; color touchscreen• Industrial PLC control• Ethernet and USB connectivity• Installed power: 15.5 kW• Compressed air consumption: 5 Nl/min• Extraction airflow: 10,000 m³/h• Power supply: 480V three-phase• Approximate dimensions: 3.66 × 3.78 × 2.40 m• Approximate weight: 2,270 kg

CEFLA - MITO, ...Complete Spraying System with SORBINI Cleaning Brush.Reciprocating Feed Through System for Waterborne & Solvent-Borne Coatings: The max. flexibility and technology for the continuous spraying of any kind of raised panels.Features: -- Machine designed with a solid structure: LASER 3D; full accessibility, thanks to the wide use of glass superficies, access doors, and extractable parts. -- Conveying System with: CFB Belt with sealed edge, driven by inverter. -- Axis driven by the powerful brushless motor and by a sophisticated toothed belt handling system, with recycling sphere bearings. The best performances in speed, acceleration, and the softness in guns motion allows to achieve the max. application quality. -- The central axis holds: (1) Gun supporting arm (removable), equipped with quick-release (predisposed for max. 4 guns); complete with: Manual height adjustment, (3) high pressure lacquer feeding circuits with recycle; lacquer filters with stainless steel fittings. -- Exclusive pressurization flows analysis and sophisticated air diffusion plenum with double fan for air intake and filtration results in: Higher lacquer saving, better machine cleaning. Circulation provided by floor mounted MZ RLQ 560, Direct-drive 4 KW , 1755 RPM motor. -- Tanks with supporting areas for filters by COLUMBUS or ANDREAS-type filters.Electronic Scanner for: Shape reading and workpieces positioning; max. efficiency in managing the guns' spraying.TECHNICAL FEATURES:Total length of the machine: 4,650 mmTotal width of the machine: 3,850 mm (4,210 mm with fan)Machine structure height: 2,500 mmElectronic control unit with: PLC and software for machine managing.Main control cabinet: Pressurized, placed at the machine infeed, along the service side complete of cable and wiring system for connection to all the users.Spraying parameters management is operated by PLC:Working programs setup, measurements of the lacquered surface & lacquer consumption, 5" color touchscreen display for diagnostic and control; possibility to exchange data from and to PLC managing complete Lines.Possibility to manage pumps for color change/washing (up to 4 pumps). -- Comes with: 2006 SORBINI/CEFLA VS/33-ACT-F, 460/3/60 Panel Cleaning Brush with brush for the top roll followed by a nozzle blow off station. (1) Head, 53" width cap. Top brush head; features timed rotating air blowers, air liner blower with nozzles. Upper mounted Anti-static ionization bar; 400 RPM brush speed.With CEFLA TM 3000, 600/3/60 V, infeed belt conveyor. -- Line is disconnected/dismantled per last (8) photos.