AUTOQUIP 36S128 DL Double Long Scissor Lift.12,800 Lbs. max. cap. with standard 24" x 98" smooth steel platform top. -- 36" Travel with a 7-1/4" height and 43-1/4" raised height; (35) Sec up and down speed. Base frame 24" x 98". -- Power unit with 5 HP remote Super Torque Motor, 240/480 V, 3-Ph, fan-cooled, Intermittent (2 minute) duty. -- Polyethylene hydraulic fluid reservoir with a capacity of 5 gallons. Supply voltage must be specified. -- Complete with; -- Hand held up/down push button control with 10' cord, velocity fuse on cylinder, and maintenance locks on baseframe, -- Options; Guarded foot pedal control, Accordion skirt, larger platforms available. NOTE: Surface mounted lift. Unit is painted AQ black; Pricing subject to change.

AUTOQUIP 48S60 SCISSOR LIFTThe Series 35 Scissor Lift Tables are designed and built to provide long-service life, durability, and outstanding lifting power. Series 35 models range in travel from 24″ to 60″ with lifting capacities up to 15,000 lbs. More models and standard options than any other competitive lift table allows for easy customization to meet your specific needs. Single-piece, steel reinforced legs and a 1/4- to 3/8-inch-thick steel platform make for extremely solid construction and easy adaptability. Solid steel leg and added stiffeners provide optimal overall stability and straight, repeatable tracking of the rollers as the lift raises and lowers.Specifications -- 6,000 Lbs Cap., electro-hydraulic operation. -- With 48" x 64" smooth steel platform. -- 7" Lowered height, 48" travel to raised height of 55"; -- 2-Cylinder design -- Complete with: Velocity fuse on cylinders, and maintenance locks on base frame. -- Unit is painted AQ black; .Please note: -- Autoquip to supply recommended GPM flow to achieve a 60 sec. lift time when all (4) lifts are operated at the same time. -- There will still need to be a mechanism to switch on/off (sequence) 1, 2, 3 or 4 lifts at a single time and there may need to be valving to ensure level lifting. -- AUTOQUIP cannot ensure the latter or warranty these lifts since AUTOQUIP is not supplying the complete lifts.

BAKER BDDO Board DedusterSpecifications: -- Conveyor Height: Min: 24", Max: 34" -- Feed Speed: Fully variable 0-700 feet (0 to 213.36 m) per minute -- Brushes: 3 Nylon brushes (replaceable) 0.040" diameter 8 strips per brush -- Height Adjustment: Hydraulic hand pump -- Dust Hook-up: 6" diameter recommended air flow dust pipe for 1,300 CFM (37 m³/min) -- Power: 3 Brush Motors with 2 HP (1.49 kw) TEFC on each brush. -- Hopper Conveyor Drive: 2 HP (1.5 kw) variable speed frequency drive. -- Board Width: Up to 8" -- Board Height: Up to 2.5"—modifications to this are available upon request) -- Board Length: Min: 36" Max: 55" or longer if dead rollers are added

BALEMASTER - EO-650: Horizontal Auto-Tie Baler Specifications: • 25 HP Motor.• 8"; Main Cylinder.• Hopper Opening: 46";x 50";.• Bale Size: 48"; x 30"; x (variable).• Main Ram Face Pressure: 75 PSI.• System Pressure: 2,000 PSI.• Total Compression Force: 100,500 Lbs.

BALEMASTER - 4550G-10: Auto-Tie Horizontal BalerSpecifications: --27"; x 40"; Opening. -- 50 HP. -- 10"; Cylinder. -- 30"; x 40"; x Variable Bale.

BARKER 600 HP BOILER, BIOMASS-FIRED: -- BARKER Boiler and Fuel System built & tested in 2011 as a pilot unit. Successful testing has been completed. This surplus equipment includes the following main features: -- Combustion Temp Capability- 2,000 deg. F.; Steam Flow 24,000 lbs/hr saturated; Steam Pressure 1,500 PSI @ 600 deg. F. -- Fuel Feed rate - 3,000 Lbs/hr at 1/4" biomass (5% moisture) -- Heat Input - 7,500 btu/Lbs HHV @ 22 mmbtu/hr. -- All equipment has less than 2,500 actual operating hours since installation.EQUIPMENT MAJOR COMPONENTS: Combustor, Cyclonic combustion technology, Refractory lined Heat Recovery. Steam Generator. Rotary Drum Dryer for Fuel drying - capable of 30% moisture reduction (at the above combustion parameters) and 1.5 tons per hour (installed as used equipment).BALANCE OF PLANT FUEL FEED SYSTEM: Live-bottom bin, Bunker, Feed conveyors, Wood hog, Vibrating screen, Drag and screw conveyors. Boiler water system - feed pump, water and steam piping Emissions Control: All required bag houses (SJVUAPCD) California permitted. -- Now REDUCED PRICE from $1.5 million !!

BELFAB RPJ26-121 Pulse Jet Dust Collector with Rotary Air Lock and Transfer Fan.Specifications: -- 15,285 CFM approx. baghouse dust collector with (121) filter bags at 10-feet long with metal cages. Total of 1,884 sq. ft of cloth area. -- Filter Cleaning: Reverse Pulse Jet (RPJ) via plant compressed air that is sequenced by diaphragm valves/solenoids/manifold thru to a Venturi that injects a burst of air pressure to dislodge the dust build up on the outside of filter bags. This is a continuous process during the operation of the dust collector. (no shut down is needed). -- Main Fan: 75 HP side-mounted blower motor. with approx 26" dia. inlet. Rated at approx 15,000 CFM @ 15" SP. -- Comes with: Main starter with control panel. -- System includes: Relay/Transfer fan, steel structure support stand, low height as waste is transferred by fan, safety ladder/platform, safety railing, and approx. 20" Rotary Air Lock. -- Housing is about 8'-5" square by about 23' high overall. Weight with structure is about 8,600 Lbs. Note: Round cone section with storage capacity of about 246 cu ft may not be included. in above height and weight. -- Available in May 2025.

BELFAB - NBM5-20: Modular Dust CollectorPatented modular technology; 6,000 CFM with a static pressure of 10"; designed for current need that can easily be upgraded, as required. -- Exterior design; each "NBM" filter module with: (1) Service door & (1) explosion door per NFPA 68 safety regulations; unit has (5) filter modules. -- Each "NBM" filter module with: (18) 7" x 60" Poly twill filter tubes. -- Direct drive centrifugal Fan Assembly with: HUMMER 20 HP @ 1,800 RPM High Efficiency TEFC blower Motor; UL & CSA approved; AMCA Class-C anti-spark blower assembly with: Heavy Duty steel impeller; 16" inlet dia.; 825 sq. ft. filter surface area. -- Control Panel & Shaker Mechanism includes: (2) Interlock magnetic starters; (1) for the blower motor & (1) for the automatic shaker mechanism; adjustable timer; pilot lights all pre-wired. -- Includes: (10) Plastic drum.

YM-1000 1.3 YARD 4 TINE Orange Peel GrappleSpecifications: -- Operating Weight 3,100lbs -- Opening Width 78 3/4" -- 4 Tine in stock - Ready to ship -- Rotating -- Hanger Included

YM-800 1 YARD 4 OR 5 TINE Orange Peel GrappleSpecifications: -- Operating Weight 2,400lbs -- Opening Width 71 1/8" -- 4 or 5 Tine in stock - Ready to ship -- Rotating -- Hanger for Extra Cost

DISA CS-4 MAXI Dust collector with Rotary Air Lock. Approx. 16,000 CFM at 8.7:1 air-to-cloth ratio; 1,725 sq. ft. of filter area, with (128) filter bags filtering to 3-micron. -- General Info: CS-4-M consists of (3) filter modules & one entrance module. -- Comes with: DISA, S56-500 Material Handling fan powered by 50 HP TEFC motor. Fan nominal rating: 16,000 CFM @ 9" SP. Fan is currently mounted on elevated support but can be installed on the ground as well. -- (3) Reverse air bag cleaning modules with motorized fans that clean the bags every (4) hours of operation automatically, each with 2 HP fan motor. A damper at inlet closes during cleaning cycle to prevent blowback. -- Complete with: Hopper bottom as collected dust is conveyed to one end by a drag chain along to one end where dust is picked up into Transfer fan. Filtered air return unit, 8' support structure to allow for dumpster under Dust Collector. -- Includes: Control panel, motor starters and switches, and Explosion Panels. Material handling main fan w/motor mounted to side of base module. -- 26" diameter inlet pipe, 97" clearance under collector for dump hopper, free standing steel bolt-together structure, -- Features: Dust transfer from bottom of Rotary Air Lock to enclosed container by separate floor mounted material handling fan, approx 7.5 HP. -- Note: Pictured storage bins are not included.

DIXIE - 15 HP: Dust Collector Specifications: -- 15 HP Motor. -- 1,760 RPM. -- Air Pulse filter bag cleaning System. -- (2) Bottom outlets. -- 15" Diameter: Inlet pipe size. -- Wall-mounted motor control station. -- Overall Collector footprint: 90" Wide x 67" deep (101" with rear-mounted fan) x 122" high.

DONALDSON / TORIT DWST6-5 Cartridge Dust CollectorDownflo® WorkStations (DWST) fit anywhere on the plant floor and apply NO restrictions to worker movements or visibility. The full line of WorkStations are designed specifically for those in-plant areas where dirty and/or noisy operations are out in the open—grinding, sanding, chipping, batch mixing or welding. The DWST delivers exceptional performance in metalworking, woodworking, and process applications where high filtration efficiency and ledge less construction is often a requirement. Specifications: -- (5) Module System, each with 10 HP motor, 7,000 CFM. -- (4) Ultra-Web cartridges. -- Pulse-cleaning manifolds and ventures, (2) dust drawers. -- (1) Acoustical panel per module. Louvers mounted on lower section of unit.Includes: -- (1) IEC control panel includes 460-volt motor starters, circuit protection for each motor, transformer, programmable logic controller. -- Magnehelic gauge mounted in a panel door, start/stop buttons, and a through-the-door disconnect switch. -- Pulse cleaning can be continuous or after-shift. -- All components are IEC rated. The enclosure is rated Type 12. -- 1"; Compressed Air Regulator with Filter Separator and Gauge, Black Iron Fittings, and Black Iron Piping Required for Cleaning System. -- Provides a 1"; Common Connection Point for Design Shutters to Tie into with Existing Compressed Air System.

DOUCET ERS-96/RS-75/AP-508 MULTI-BLADE PANEL GROOVE/RIP SAW SYSTEM:The Doucet ERS-96/RS-75 Automated Panel GROOVE/RIP Saw System is designed to GROOVE and/or RIP panels as well as edge the sides of core materials. Ideal for plywood, OSB, MDF, HDF and other composite panels.This Line was originally designed for Engineered Flooring Blanks.ERS-96 Grooving Specifications:40 HP - 3,500 RPM belt driven saw arbor motor. Material width cap. 96" maximum. Material thickness 0.5" - 0.625" maximumGrooving pattern on 4" centers across the 96" width of panel. Depth and width of groove approx. 3/16" kerf/width by 1/8" deep.3" dia. Arbor shaft with 1.5 HP motor for motorized arbor adjustment for panel thickness. Saw arbor accessible from above for tool changes. -- Feed system:5 HP - 1,750 RPM feed motor, variable feed speed up to 75 FPM.(4) Powered bottom feed rollers & adjustable top idler pressure rolls with positive panel support during grooving operations.Top & bottom feed rollers have slip resistant urethane covered rollers, feed rollers are chain driven with air tensioning. -- Complete with:Dynamic saw arbor brake; Infeed anti-kickback fingers; Saw blade safety interlock cover; 12" dia. dust collection outlet (4,000 CFM required). RS-75 Ripping Specifications:40 HP - 3,500 RPM belt driven saw arbor motor. Material width cap. 60" maximum. Strip width cap. 2.5" minimum. Depth of cut 0.25" - 0.75" (6 - 19 mm) maximum.3" dia. Arbor shaft with 1.5 HP motor for motorized arbor adjustment for panel thickness. Saw arbor accessible from above for tool changes. -- Feed system:Doucet AP-508 Automatic panel feeder with scissor lift to automatically feed panels as needed.5 HP - 1,750 RPM feed motor, variable feed speed up to 75 FPM.(4) Powered bottom feed rollers & adjustable top idler pressure rolls with positive panel support during grooving operations.Top & bottom feed rollers have slip resistant urethane covered rollers, feed rollers are chain driven with air tensioning. -- Operator Interface: Doucet OI/HMI Control System for automatic loading & stacking with minimal human intervention other than a forklift operator to bring in new material and remove the processed parts/strips. -- Complete with:Dynamic saw arbor brake; Infeed anti-kickback fingers; Saw blade safety interlock cover; 12" dia. dust collection outlet (4,000 CFM required). -- Options Include: (1) Doucet AP-508 Automatic panel feeder with Indexing scissor lift. (1) Cross Transfer Chain Conveyor to feed panels sideways by the long edge through the Groover, max width 96". (1) Cross Transfer Chain Conveyor to feed panels short end wise through the panel RIPSAW, max. width 60" (1) Outfeed Lift Table to automatically stack ripped strips. Maximum weight of stack: approx. 5,000 LBS. -- Actual Model is DOUCET RS-75/ERS-96/AP-508

DUST TECHNOLOGY DT-50 Modular Dust Collector5 HP BALDOR Motor, compact 2-bag free-standing & self-contained Heavy Duty Dust Collector, rated @ 2,400 CFM, 9" - 11" static pressure at fan. -- Equipped with: 10" Inlet dia., (2) Cotton Filter bags with 66 sq. ft. filter area and (2) Plastic Collection Bags w/ 30 cu. ft. collection capacity. -- (2) Double "T" Bolt Straps and (2) Quick Release Metal Straps. Includes: Magnetic Starter

DUST TECHNOLOGY DT-150 Modular Dust Collector Free-standing self-contained internal air system, 15 HP Motor, rated for 6,000 CFM, 4-bag unit, 60 cu. ft. collection capacity. -- (4) Upper cloth filter bags with 133 sq. ft. filter area; 14" inlet dia., dust baffling system to fill bags evenly. -- Includes: 15 HP motor, magnetic starter, (4) Upper cloth filter bags with 133 sq. ft. filter area and (4) lower plastic disposable collection bags

DUST TECHNOLOGY DT-75 Dust Collector7.5 HP BALDOR Motor, compact 3-bag free standing & self-contained heavy-duty dust collector, rated @ 3,450 CFM, 9" - 11" static pressure at fan. -- Equipped with: 12" Inlet dia., (3) upper filter bags with 99 sq. ft. filter area (patented BEANE bags designed to be 99% efficient to .5 microns). -- Dynamically balanced sand cast poured aluminum high quality impeller with easy access; 45 Cu. ft. collection cap., dust is collected in 6-mil thick clear plastic or canvas collection bags for easy disposal or reuse, a unique adjustable baffling system assures even filling of bags. -- Includes: Manual motor starter with thermal overloads & push button station.

DUST TECHNOLOGY DT-100 Dust Collector3-Bag free-standing & self-contained heavy-duty dust collectorSpecifications: -- 10 HP BALDOR Motor, compact 3-bag free standing & self-contained heavy-duty dust collector, rated @ 4,450 CFM, 9" - 11" static pressure at fan. Equipped with: -- 12" Inlet dia., (3) cotton needle felt upper filter bags with 99 sq. ft. filter area or patented BEANE bags designed to be 99% efficient to 0.5 microns. -- Dynamically balanced sand-cast poured high-quality aluminum impeller with easy access; 45 Cu. ft. collection capacity. -- Dust is collected in 6-mil thick clear plastic or canvas collection bags for easy disposal or reuse, a unique adjustable baffling system assures even filling of bags. -- Includes Push-button Magnetic starter control.Dimensions: 24" Deep x 136" High x 107-1/2" Length; Weighs (810) Lbs.

DUST TECHNOLOGY DT-250 Modular Dust Collector Free-standing self-contained internal air system, 25 HP Motor;Specifications: -- Rated for 9,800 CFM, 5-bag unit, 75 cu. ft. collection capacity. -- (5) Upper cloth filter bags with 165 sq. ft. filter area; 16" inlet dia., dust baffling system to fill bags evenly. Supplied with & Includes: -- 25 HP motor with magnetic starter, -- (5) Upper cloth filter bags and (5) lower plastic collection bags. -- (5) Double "T: Bolt straps. -- (5) Quick release metal straps. -- Roll of 50 Lower Plastic Dust Collection Bags, 24" Dia. X 72" Long.Three Year Comprehensive Warranty

DUST TECHNOLOGY DT-200 Modular Dust Collector Free-standing self-contained internal air system.Specifications: -- 20 HP Motor, rated for 7,500 CFM, 4-bag unit, 60 cu. ft. collection capacity. -- (4) Upper cloth filter bags with 132 sq. ft. filter area; 14" inlet dia., dust baffling system to fill bags evenly. Features & Includes; -- 20 HP motor, magnetic starter; -- (4) Upper cloth filter bags and (4) lower plastic collection bags. -- (4) Double "T": Bolt straps. -- (4) Quick release metal straps. -- Magnetic starterThree Year Comprehensive Warranty