HURST SERIES 45 207.5 HP 60 PSI HOT WATER NATURAL GAS FIRED FIREBOX: -- Specifications:Built New in 2016...Complete, never installed & ready to deliver! -- Efficient 3-Pass Design NATURAL GAS FIRED FIREBOX -- ASME Code Constructed & Stamped for 15 PSI Steam / 30-100 PSI Water -- Registered with the National Board of Boiler Inspectors -- Easily Maintained, Designed for Efficiency, Large Furnace Volume for Ultimate Combustion Efficiency -- Unified Refractory Base Floor, Steel Skids and Lifting Eyes -- Low Heat Release, Factory Insulated – 2"; Mineral Wool, Factory Jacketed & Painted -- Easy Access to Fireside Surfaces n Ample Waterside Clean-Out Openings -- Fully Automatic Operation, U.L. Listed, Forced Draft Burners -- Wet Back Construction -- U.L. Listed Controls & Trim -- Factory Test Fired, Flame Observation Ports Front & Rear.BOILER DESIGN: Three-Pass “FireBox"; design with stress relieving “Wetback"; Firetube construction. Hot Water pressures models are from n 8.5-415 HP } 100 psi. max. n 500-813 HP } 60 psi. max. Built to Section-IV ASME Code. Hot water temperature not to exceed 250° degrees F. at or near the outlet of boiler.HOT WATER MODEL TRIM: Safety relief valve, operating temperature control, high limit temperature control with manual reset, combination pressure & temperature gauge, low water cut-off control with manual reset.HOT WATER SUPPLY: 180 D/F RETURN: 160 D/F -- FIRESIDE HEATING SURFACE: 830 SQ.FT. FURNACE VOLUME: 132 CU. FT. HOT WATER OUTLET: 8", HOT WATER RETURN: 6", DRAIN CONNECTION: 2".BURNER: Matched UL listed “forced draft"; power burners with factory pre-piped, wired and tested fuel configurations for natural gas, propane (LP) gas, No. 2 (diesel) oil, or combination of both gas/oil.All units are factory packaged with operating controls, relief valves, burner and fuel train. Installation is made simple in that only service connections are needed to place in operation.High density 2"; mineral wool insulation assures lower radiant heat loss. In addition to meeting the requirements of U.L., burner systems are optionally available to meet the requirements of FM, IRI, MILITARY and others. -- Actual Model is HURST S45 – G – 207.5 – 60W

HURST 205 HP / 6.9mm BTU / 15 PSIG WET WOODY BIOMASS FIRED BOILER/STEAM PLANT: -- Specifications: Complete in-place system with the following features: -- 205 HP Biomass Wood Fired Boiler, 7,073 PPH, gross steam output @ 212° F. -- Low Pressure "Fire Tube" design fire box model FB-1332-15-UF, built in accordance with ASME Code. -- Operator Interface:Allen Bradley PLC with Power Supply Rack. Pentium-based computer with network & modem remote communication capabilities with operator interface software. -- RSView Runtime for automatic operating of the steam pressure, temperatures, fuel flow & combustion airflow. -- The control system incorporates a 4-20 milliamp steam pressure transmitter to sense any changes in steam flow, boiler pressure, & regulates the fuel feed & combustion airflow accordingly. -- Complete with:Additional details on file for the scope of this Complete System's original project.NOTE: Building that houses Boiler can be included with Boiler if desired by Buyer.

HURST 600 HP Waste Fired Boiler; -- Specifications:Complete in-place system with the following features: -- Decommissioned July 2019. -- 150 PSI. (300 PSI max wp), -- 20,700 Lbs per hour. -- Fuel House, Boiler Building and all Controls -- System has been "pickled" to maintain tube integrity.

HUSTLER - FC-2, ...ScreenSpecifications: -- OD at the longest point: 104" -- Long at longest point: 122" -- Tall at the tallest point: 65"Equipped with: -- (2) Shutoff switches

IMPERIAL CM-002 CMaxx Dust Collector The CMAXX™ was designed with revolutionary cleaning technology that insures maximum pulse cleaning power. The CMAXX™ housing is the largest in the industry with the lowest internal velocities. This large housing causes more dust to drop into the hopper before attaching to the filters. The low internal velocity combined with DeltaMAXX™ filters makes this the most efficient dust collector in the industry.Specifications: -- 700 s/f Filter Media 2.55-1 Air to Media Ratio -- Main Handle Operator -- Overload Protection -- NEMA 4 enclosure -- Push button start -- Emergency stop button -- Run indicator lightIncludes: -- 7.5HP Fan Motor Starter with 1,790 CFM -- Integrated Dwyer DCT1000 Control -- Window kit for easy access to dust collector settings

IMPERIAL CM-006 Cartridge Modular Pulse Jet Dust/Fume Collector. Designed to be the strongest, safest, and most efficient dust and fume collector in the industry. -- Overall Specs: 4,800 CFM with 2,800 sq. ft. of total filtration media operating at 2.0:1 Air-Cloth-Ratio (ACR). Factory provided compressed air (clean - dried) is supplied to manifold mounted valves providing efficient continuous pulse jet Filter Cleaning System. -- Fan/Motor: MS-180-HD-70-20 Fan driven by 20 HP premium E motor. Efficient backward-inclined fan wheel. Manual slide gate damper on fan discharge. Fan-Silencer at fan outlet. Fan capable of 4,800 CFM at 13" SP. -- Electrical Control Panel: Nema 12 (indoor) enclosure with main breaker houses fan Start, E/stop, continuous On-Demand selector switch, Local/Remote selector. Soft Start drive to reduce power peaks on start up. -- Construction/Housing/Features: Heavy 7 - 10 gage construction with no external bolt holes guaranteeing no leaks for life. Filter access door with lockable handle, heavy duty latches for one handed operation. Tool-free filter change out with 'Even-Lock technology positive stop double sealed ensures cartridges are always installed properly. Filters are fully grounded to dust collector housing. OSHA compliant full length platform and adder access. Bolted support stricture with 54" clearance for 55 Gal drum & adapter.. Discharge via 10" Rhino heavy duty collection drum sealed cover kit requires not airlock with slide gate closure, tool-free sliding coupler, and grounding wire. -- Comes with: High Entry inlet with staggered angle inlet baffle plate provides filter protection and allows material to enter at filter level causing the natural downflow material primary separation effect. Horizontal square to round transition. DWYER DCT1000 control manages the Filter Cleaning System with user-friendly software menu. Solenoid time/on-off/settings and high/low differential pressure control capability Auto/Manual control option. Compressed air pressure regulator and filter. -- Optional: Updated control panel to include a Variable Frequency Drive (VFD) to replace the Soft Start drive and keypad on cabinet door. Upgrade Controls to Include VFD. VFD reduces inrush current at startup saving energy. Also regulates system airflow by maintaining static pressure at the collector inlet. This reduces the load on the motor saving operating cost, instead of dampening the airflow with an outlet damper that is required on other starter options. On system shut down the VFD slows the fan down to a preset speed of 20 HZ for 5 minutes (the duration of the down time cleaning cycle), this prevents dust from backflowing out of the collector due to the cleaning system pressurizing the collector creating a back flow through the ductwork. Please inquire for price.

INDUSTRIAL RESOURCES PASS ONE Pallet DismantlerRemove stringers with a single stroke and dismantle 400 plus pallets per shift with "one" operator. -- Machine size; 14' L x 5' W, table size 54" L x 60" W. Stringer cap. 54". -- Includes; Hydraulic power pack, 7.5 HP, 12 GPM @ 750 psi. Manual variable speed valving. Hydraulic cylinder 2" bore x 62" stroke. -- Options Include; Upper arm lift to provide ease of maintenance, greater flexibility, table rollers to help simplify pallet handling and 60" pallet length. -- Cycle time in / out approx. 7 Sec.

INGERSOLL-RAND UP6-15C-125 15 HP Single-Stage Horizontal Tank-Mounted Rotary Screw Air Compressor, with 2,313 Hrs. (as of 2/16/24) Specifications: Cap. 55 CFM, Max. pressure 125 PSI. Pump speed 6,250 RPM. Sound level 69 dBA. Equipped with: High efficiency close coupled air end. Motor shaft-mounted centrifugal blower. Electronic stepper motor inlet air control. 2-Stage Air-cooled aftercooler. Total positive lubrication system, with Spin-on filter. Compartmentalized sound enclosure. Complete with: 80 Gallon Cap. 24” Dia. x 33” L Horizontal Air Receiving Tank. CURRENCY NOTE: Negotiable Price is listed in U.S. Dollars.

INGERSOLL RAND D144IN 85 CFM Non-Cycling Refrigerated Compressed Air Dryer Specifications: Cap. 85 CFM. Max. working pressure 203 PSI. Max. inlet temperature 60° C (140° F). Refrigerant type R-134A. Equipped with: Aluminum braze plate heat exchanger. Variable speed fan. Microprocessor control, with Graphic display, LED Dew point indicator, Energy saving mode, & History of last (10) alarms. Remote alarm signal terminal. High pressure switch. Fully-adjustable programmable electronic drain valve. CURRENCY NOTE: Negotiable Price is listed in U.S. Dollars.

MURPHY-RODGERS - HEC-216-S/10: 33,000 CFM Continuous Duty Automatic Self-Cleaning Pulse Jet Baghouse Dust CollectorEquipped with: -- (216) 5" Dia. x 10' L Cloth filter bags for a total of: 2,827 sq/ff. of filter area. -- (2) 42-1/2" W x 68" H & (2) 40-1/2" x 68" H Top access doors. -- (3) Front & (2) side 27" W x 54" H Filter access doors. -- (2) Square cone bottom hoppers each with: 25" x 25" Discharge openings. -- System utilizes: (2) 4-1/2’ x 6’ x 4’ H Waste containers (NOT included). -- CHICAGO 100 HP - 1,780 RPM Roof Mounted Blower with: 41"; Dia. inlet. -- Motorized dampers for winter & summer modes. -- Winter mode: Directs air back into building, reducing heat loss. -- Summer mode: Directs air outside, cooling building. -- Electrical controls (as pictured). VFD needs to be repaired or replaced.Complete with: -- Spare Filter Bags.NOTE: Installed Used in 2016 with "New" 100 HP motor, new bearings in blower & "New" spring mounts.

MURPHY-RODGERS - MRSE-14-RAL: Baghouse Dust CollectorSpecifications: 14" Inlet dia.; 4,836 CFM; (63) bags with: 520 Sq./ft. filter area; 9.3:1 air-to-cloth ratio; 20 HP fan motor; primary separator built into unit; secondary separation of fine particles by filter bag section; -- Equipped with: -- Rotary Air Lock. -- Fully automatic shaker controls with: Electric shaker as standard; consists of panel box with shaker starter; transformer for 115 V circuitry; solid-state timer for fan deceleration & shaking cycle. -- All necessary relays and internal wiring inside the panel box.

7.5 HP TEFC BALDOR Motor, 2,960 CFM at 6" W.G., free-standing interior unit, designed for (6) filter bags mounted over two plastic waste bags or barrels for waste collection. -- 10" Inlet dia.; 128 sq. ft. filter area, 66 cu. ft. storage cap.; quick clamp barrel removal. -- It comes with barrels and bags as shown. -- Overall height is 129"; requires 26" x 108" floor space..Magnetic Starter included

MURPHY-RODGERS MRZ 17/16L Interior/Open 6 Bag Dust Collector with Auger and Rotary Air Lock General specs: Approx. 7,600 CFM @ 8" SP. (6) top filter bags @ 24" dia. by 72" long. (6) bottom disposable plastic dust storage bags. -- Fan/Motor: 25 HP BALDOR TEFC motor direct driven fan with electrical starter. 17" diameter inlet, with lifting hooks. The bag collector motor is brand new and has never been powered on or fired up. -- Comes with: Main approx. 17" dia trunk line, shut-off, and Quick clamp removal for filter and plastic bags. -- All steel construction with rugged support legs. Air Deflectors allows operator to adjust the air flow and amount of waste evenly into the 6 waste bags. -- Note: NFPA 664 (Fire Code) states that a max. of 5,000 CFM is limit allowed for indoor enclosure-less dust collectors.

MURPHY-RODGERS MRJ-610-122 Pulse Jet Dust Collector with Rotary Air Lock and Transfer Fan.Specifications: -- 8,500 CFM approx. @ 9 to 1 air to cloth ratio baghouse dust collector with (60) 10-feet long filters; total cloth area of 943 sq. ft. -- Filter Cleaning: Continuous Self-cleaning Using Compressed Air. -- Main Fan: 30 HP top-mounted blower motor. with approx 18" dia. inlet. --System includes: Relay/Transfer fan, steel structure support stand, low height as waste is transferred by fan, safety ladder/platform, top safety railing, and approx. 16" Rotary Air Lock.Actual model is MRJ 610 -122.

NEDERMAN S-1000 BAG FILTER Dust Collector w/ Auto Bag ShakerThe NEDERMAN S-Series Baghouse Dust Collector is quick to install and easy to operate. It's the ideal solution for a smaller shop or single work-cell operation.Specifications: -- With a 10 HP motor and a 5,000 CFM @ 7" WG and 360 Sq/ft of filter media. -- 10 HP - 1,750 RPM TEFC Motor, (24) Beane material filter bags and magnetic starter. -- Features: Easy installation, typically (1) hour; quiet operation, (3) waste discharge points. Inlet opening 16". Includes: -- Auto Bag ShakerAvailable in 208/230/460 V, 60 Cy, 3 Ph. Must specify Voltage at time of orderAvailable option:- Aluminum Impeller: - 45 Gallon Drum Discharge - Single Drum (3 REQUIRED)- 230 Gallon Dump Bin: Available spare parts:- Filter Bag (24 Filters)- Plastic Bags (Roll of 90 - 8 mil thickness) - 500mm Clamp (bags, barrels, and bin)

NEDERMAN S-750 BAG FILTER Dust Collector w/ Auto Bag ShakerThe NEDERMAN S-Series Baghouse Dust Collector is quick to install and easy to operate. With a 7.5 HP motor and a 4,500 CFM @ 6" WG it's the ideal solution for the small shop or single work-cell operation. -- Specifications: 7.5 HP - 1,750 RPM TEFC Motor, (24) Beane material filter bags and magnetic starter. -- Features: 243 Sq/ft of filter media, easy installation, typically (1) hour; quiet operation, (3) waste discharge points. Inlet opening 11". -- Available in 208/230 or 480 V, 60 Cy, 3 Ph. Must specify voltage at the time of orderIncludes: -- Auto Bag ShakerAvailable options:42 Gallons Drum Discharge - Single Drum (3 REQUIRED)230 Gallon Dump BinAvailable spare parts:- Filter Bag (24 Filters)- Plastic Bags (Roll of 90 - 8 mil thickness) - 500mm Clamp (bags, barrels, and bin)

NEDERMAN - S-1000, BAG FILTER Dust CollectorThe NEDERMAN S-Series Baghouse Dust Collector is quick to install and easy to operate. It is the ideal solution for the small shop or single work-cell operation. -- Includes: 10 HP Motor; CFM range from 4,000 CFM @ 8" WG to 5,000 CFM @ 7" WG. -- Equipped with: 10 HP - 1,750 RPM TEFC Motor; (24) Beane material filter bags; (3) plastic waste collection bags; (3) clamps for easy removal of waste bags; magnetic starter. -- Features: 360 Sq/ft. of filter medial; easy installation, typically (1) hour; quiet operation. -- Inlet opening 15". Two units available!

NEDERMAN S-750 BAG FILTER Dust Collector. The NEDERMAN S-Series Baghouse Dust Collector is quick to install and easy to operate. With a 7.5 HP motor and a 4,500 CFM @ 6" WG it's the ideal solution for the small shop or single work-cell operation. -- Specifications: 7.5 HP - 1,750 RPM TEFC Motor, (24) Beane material filter bags and magnetic starter. -- Features: 243 Sq/ft of filter media, easy installation, typically (1) hour; quiet operation, (3) waste discharge points. Inlet opening 11". -- Available in 208/230 or 480 V, 60 Cy, 3 Ph. Must specify voltage at the time of orderAvailable options:42 Gallons Drum Discharge - Single Drum (3 REQUIRED)230 Gallon Dump Bin

NEDERMAN S-500 BAG HOUSE DUST COLLECTOR. -- Open Bag house designed for interior application; 5 HP TEFC material fan motor, 1,750 RPM; free standing 2,000 CFM open frame bag house, 162 sq. ft. of filter area via (16) beane material filter bags; 7.5" W.G. static pressure. -- Bottom discharge into (2) plastic waste collection bag. -- Includes: Side-mounted blower assembly with support legs; (2) quick disconnect clamps for the plastic bags. Starter motor with push buttons. Option:42 Gallons Drum Discharge, Single Drum (2 REQUIRED FOR COMPLETE S-500)

NEDERMAN S-1000 BAG FILTER Dust Collector. The NEDERMAN S-Series Baghouse Dust Collector is quick to install and easy to operate. It's the ideal solution for a smaller shop or single work-cell operation.Specifications: -- With a 10 HP motor and a 5,000 CFM @ 7" WG and 360 Sq/ft of filter media. -- 10 HP - 1,750 RPM TEFC Motor, (24) Beane material filter bags and magnetic starter. -- Features: Easy installation, typically (1) hour; quiet operation, (3) waste discharge points. Inlet opening 16". Available in 208/230/460 V, 60 Cy, 3 Ph. Must specify Voltage at time of orderAvailable option:- Aluminum Impeller: - 45 Gallon Drum Discharge - Single Drum (3 REQUIRED)- 230 Gallon Dump Bin: Available spare parts:- Filter Bag (24 Filters)- Plastic Bags (Roll of 90 - 8 mil thickness) - 500mm Clamp (bags, barrels, and bin)