LHI AUTOMATIC RAKE FEEDER with the following equipment: -- Panel Feeder with up to 18' Long x 5' Wide x 1" Thick Sheet Capacity (with 4' min. sheet length) -- Feeder loads from right side when viewed from the End of the Scissors Lift -- Auto-cycle for Rake Feeder -- 6' Line-Up conveyor with Fence & Powered Pinch Wheel -- 8000 Lbs. Tandem Scissors Lift with 5' x 17' top, 600-Volt, 3-phase, 2 HP motor -- 5-Section Gravity Rollers on Scissors Lifts -- 12' Powered 5 Strand Chain Conveyor Feeds Tilt Lift w/forward/ reverse, jog controls -- Wired for 600-Volt/3-Phase/60-Cycle Operation (other voltages available) -- Arranged for Customer Provided MultiScore Panel Ripper with right side arbor loading

LHI MODEL RFPR ROLL FEED PANEL RIP SAWWith the following Standard and Optional Equipment: -- Roll Feed Panel Rip Saw - 72" Arbor - 50 HP motor -- 10 to 80 FPM (4-speed programmable or potentiometer) -- (8) Polyurethane feed rollers -- 10" Dia. blades (thickness-1/8" to 1-1/4") Infeed Scissors Lift 4,500 Lbs capacity -- 4' x 8' top -- (3) 2"; x 3"; support tubes for fork access -- 110 VAC / 1-Ph power unit -- Foot pedal control -- Automatic up-indexingOutfeed Scissors Lift 4,500 Lbs capacity -- 4' x 8' top -- (3) Support ramp/cross-bars to allow for access -- Auto down indexing -- 110 VAC / 1 Ph power unit -- Foot pedal controlSawblades: -- (10) 10" x 40T x 4-3/16 Bore, TGC Blades -- (10) Blade Collars, 3-15/16" ID x 4.18" bore x 1.25" wide Quick-change arbor setup with the second arbor: -- Arbor change cart (included with the arbor setup that comes with the saw to allow roll-out) Second Arbor Setup Includes: -- Cart -- Blade Box -- Arbor, Bearing -- Sheave -- Throat Plate Rack -- (6) Throat Plates Quick Change Kit: -- Belt Guide -- Belt Tensioner -- Hyd. Arbor Lock Quick Change Kit permits the operator to release the belt and unlock the arbor from the front side of the machine. Without the kit, the operator must open the rear guard to remove the belt and unlock the arbor -- (10) Blades for the second setup -- (10) Collars for the second setup 16-week ESTIMATED delivery: -- Delivery assumes order and down payment are received within (1) week of the date of quotation. Installation technical assistance for $115/Hr plus travel time and expenses Customer responsible for rigging Quote assumes customer will deliver material for testing (if required) Warranty: (1) Year mechanical parts (electrical controls excluded) This quotation is valid for 30 days. ESTIMATED DELIVERY DATE:The delivery date is quoted as 'estimated' because the equipment we manufacture is built to order and to our customer's specifications. This estimate is made under the assumption that there will be no interruptions of labor, material shortages, or any environmental or other unforeseen circumstances. LHI is not responsible for any installation or production costs resulting from actual delivery dates which exceed the quoted estimated delivery dates. Accurate dates for the delivery will not be available until the equipment is in the manufacturing phase. If there are custom features for the quoted equipment then accurate delivery dates will be available when testing is complete. Please consult with the factory for updates to the expected delivery date.NOTE: PRICING DOES NOT REFLECT FACTORY'S 7% MATERIALS SURCHARGE

LHI MODEL RFPR ROLL FEED PANEL RIP SAW WITH THE FOLLOWING STANDARD AND SPECIAL EQUIPMENT: Specifications: -- 72" Useable Arbor and 50 HP Arbor Motor -- 14 - 80 FPM Variable Speed Feed Rate (4-speed programmable or potentiometer) -- (8) Polyurethane feed rollers -- Arranged for 14" dia. blades and 4"; max cutting thickness -- Single Point Thickness Adjustment from 1/2" to 4" -- Arbor Quick-Change KitComplete with: -- Additional Arbor Setup, Includes: Cart, Blade Box, Arbor, Bearings, Sheave, Throat Plate Rack, and (6) Throat Plates -- (15) Blade Collars: 3-15/16" ID x 4.18" bore x 1.25" wide -- (15) 14" Carbide Tipped Blades: 40 Tooth with 4.188 bore -- Delivery ESTIMATED at (14) weeks; assumes order and down payment are received within (30) days of the date of this quotation. -- Technical Installation assistance - $125/Hr plus travel time and expenses -- Buyer is responsible for rigging -- Quote assumes customer will deliver material for testing (if required) -- Warranty: 1 Year mechanical parts (electrical controls excluded) -- This quotation is valid for 30 days.

LHI RFPR ROLL FEED PANEL RIPPER - "BUILT TO ORDER SYSTEM" with the following equipment: -- Ripsaw: -- 72" Arbor - 50 HP arbore motor and 14 to 80 FPM Variable Speed Feed Rate (4-speed programmable via VFD) -- (8) Polyurethane Feed Rollers -- Arranged for 10" dia. blades to rip panel thickness from 1/8" to 1-1/2"; -- Single Point Thickness Adjustment -- Quick-Change Arbor Kit Additional Arbor Setup Including: -- (1) Arbor Cart, (1) Blade Box, (1) Arbor Shaft, (1 set) Bearings, (1) Arbor Sheave, and (1) Throat Plate Rack Automatic Infeed System: -- 4,500 Lbs. Capacity Hydraulic Scissors Lift with (4) loading ramps to feed and align 4’ x 8’ sheets into Panel Saw -- 110VAC/1PH Scissors Lift power unit -- Auto-Cycling Rake Feeder -- 6’ Line-Up Conveyor With Power Pinch WheelOutfeed Scissors Lift: -- 4,500 Lb. Capacity Hydraulic Scissors Lift with 4' x 8' top, (3) support ramps/cross-bars to allow fork access -- 110VAC / 1Phase power unit -- Auto Down Indexing -- Auxiliary Foot Pedal Control Blades, Collars and Throat Plates: 10" x 40T x 4 3/16 Bore, TGC, $105 eachBlade Collars: 3-15/16" ID x 4.18" bore x 1.25" wide, $135 eachAluminum Throat Plates, $35 each TERMS AND CONDITIONS: -- Delivery: 16-18 Week ESTIMATED delivery date assumes your order is received within one week of date of this quotation. -- A 5% Tooling & Steel Surcharge to be added to the machinery price when the total is known -- Installation technical assistance, $125/hr. plus travel time and expenses (if required) -- Customer responsible for own rigging -- Quote assumes customer will deliver material for testing (if required) -- Warranty: 1-year mechanical parts (electrical controls excluded) -- FOB: Shannon, MS 38868. ESTIMATED SHIPPING DATE: 16 TO 18-WEEKS --The delivery date is quoted as “estimated"; because the equipment manufactured is built to our customer's specifications. This estimate is made under the assumption that there will be no interruptions of labor, material shortages, or any environmental or other unforeseen circumstances. -- LHI is not responsible for any installation or production costs resulting from actual delivery dates which exceed the quoted estimated delivery dates. Accurate dates for the delivery will not be available until the equipment is in the manufacturing phase. If there are custom features for the quoted equipment then accurate delivery dates will be available when testing is complete. Please consult with the factory for updates to the expected delivery date.NOTE: PRICING DOES NOT REFLECT FACTORY'S 10% MATERIALS SURCHARGE

LHI 72" RFPR Wide Arbor Roll Feed Gang Panel Ripper with Custom 5' x 16' Automated Infeed -- Specifications: -- Panel Ripper with 30 HP Arbor Motor; 1/8" min. to 1-1/4" max. material thickness and 72" cutting width. -- Machine configured for arbor removal from the right side of the Saw when facing the Saw's Infeed (opposite of standard) -- Electricals arranged for 600-volt/60-cycle/3-Phase operation -- 10" Dia. blade design will cut thru max. 1-1/4" thickness; -- 3-15/16" dia. arbor with 72" of usable width cutting capacity, min. panel length 30". -- 1-15/16" FAFNIR arbor bearings; with (8) steel feed rollers on 6" centers; fixed feed speed of 80 FPM -- 47-1/4" working (passline) height -- (1) Arbor Cart is included -- (2) 4" Dia. dust collection ports on top and (1) 8" dust collection port on bottom. Recommended 1,500 CFM Includes the Following Optional Items: -- 5-Strand powered Chain Deck; 12' long; arranged to feed 5' x 16' packages onto the Scissors Lift. Complete with controls for forward, reverse, and jog. -- 5-Sections of Gravity Rollers on Scissors Lift Deck -- 8,000 lbs. Infeed Tandem Scissors Lift with 5' x 17' Deck and 2-HP, 3-Phase Motor. Lift includes a backstop for initial alignment at the Rake Feeder -- (8) Polyurethane Feed Rollers on 6" centers -- Variable Feed Speeds from 10 to 80 FPM. -- Rake Feeder for 16' long panels -- Auto-cycle for Rake Feeder. -- 6' Line Up Conveyor with Fence and Powered Pinch Roll Included Tooling: -- (36) Standard Saw Collars for Ripping -- (72) Standard 10" Sawblades for Ripping (Includes a spare set) -- (37) Standard Throat Plates for RippingQuick Setup Kit Included, Contains the Following -- Belt guide -- Belt Tensioner -- Hydraulic Arbor LockAdditional Arbor Setup Included. Contains the Following: -- Includes cart, blade box, arbor, bearing, sheave, throat plate rack, and(6) throat plates -- Blade Box -- Arbor -- Bearings -- Sheave -- Throat Plate Rack -- (6) Throat Plates SYSTEM TOTAL ............….……$174,495 7% ($12,214) materials surcharge on $174,495 = $186,709

LIGMATECH ZHR 01 RETURN CONVEYOR for RH FEED Edgebander (i.e. Brandt, OTT) & LH RETURN to the operator.FunctionAfter panels come off a through-feed machines feed-track, they are transported via (4) powered take-up belt onto a 90° transfer section and returned back to the operator.Specifications: -- Working Length, 12" - 98" (300 - 2,500 mm) max., working width 5.9" - 40" (150 - 800 mm) max., panel thickness 0.3" - 1.6" (8 - 40 mm) max. and 100 Lbs (45 kg) max. weight. -- Variable Feed-Speed, 26 - 138 FPM (8 - 42 MPM); Approx. total length of 30'; (4) 18" pickup arms, spaced 7", 8" & 14", take product from the edgebander and transport it to cross transfer conveyor section. -- Cross Transfer Section, 43-1/2" x 83", transfers material and drops it 2-1/2" onto roller transfer section, 43-1/2" x 83", which transfers material to a powered 40" x 150" flat-belt conveyor, which transfers material to a gravity roller conveyor, 40 x 72", with 2-1/2" x 35" plastic coated rollers to be received by the operator. -- Total Length of Return Conveyor is 25'. -- Actual Model is LIGMATECH ZHR 01-R-055.NOTE: (2) Photos show (3) Rollers/Feed Belts & Pusher Arms that are missing from the machine.

LIGNA 8X40 Multi-Blade Edger/Gang Saw. 40" Wide by 8" high opening. Specifications: -- Bottom saw edger with (5) blades. Powered by a 125 HP TEFC motor. -- Features stacked air cylinder setworks with independent shifting on (3) blades. -- Infeed table with pop-up chains and fence, outfeed rollcase. -- Includes: Powered infeed and outfeed steel roll conveyors.

LMC 144FTD10 Pulse Jet Dust Collector with Rotary Airlock.24,000 CFM @ 14" SPWG, 10:1 air-to-cloth ratio, contains (144), 144" long bags @ 120" long (2400) sq feet filter area) pulse jet filter. --÷ Complete with: 270 BCS-SW TWIN CITY FAN, Air Handling, Class 17 belt-driven by 60 HPTEFC motor. Volume control damper on fan discharge. NOTE: Fan is 27" and undersized for 24K CFM as was running at lower ACR. Filter to fan ducting, support legs, access ladder, explosion relief panel, -- Includes: 110 V Timer board in NEMA-4 enclosure, GOYEN diaphraghm valves, compressed air header with drain, magnehelic differential pressure gauge 0" - 10" SPWG. -- Was installed with approx. 32" trunk line. Flanged inlet, outlet, and body; perimeter railing, galvanized bag cages with Venturi's, 16 oz. singed polyester filter bags. -- Comes with: 60° Hopper, access panel into hopper, gearmotor powered LMC Rotary Air Lock, easy lift lugs. Clean air plenum with top for filter bag service, service platform. Transfer Blower is included -- 12-Ga. carbon steel construction, enclosure rated to 17" SPWG, top access cover with side door for poor weather access. --÷ Filter Dimensions: 106" x 106" x 335" high. Ready to load on a truck.

MAC 120-MCF-572 High Capacity Baghouse Dust Collection system with Rotary Air Lock (RAL) and Medium-pressure Controlled air cleaning dust Filter (MCF). TWO systems are for sale with One common Control Panel. -- Baghouse Capacity: 50,000 CFM @ 7.2:1 Air-to-cloth ratio (ACR), approx. 6,921 sq-ft of filter area based on (572) Filter bags; 120" long x 5" dia. -- Equipped with: (1) AIR TECH size 402, BISW, Backward Inclined Air Handling Fan, Class IV, with 40" inlet, ground-mounted on unitary base, flanged inlet box & outlet. For prior application fan operating point (RPM/SP) is set up for about 41,526 CFM @ 12" WG at 1566 RPM, drawing 119 BHP. the fan is equipped with a variable volume damper on discharge. Fan range is about 40,000 - 55,000 CFM. Powered by a TOSHIBA 150 HP TEFC, 444T, 1800 RPM motor packaged with a belt drive -- Bag Cleaning: Mac "Never-Miss" Cleaning System with rotating arm, diaphragm valve for pulse cleaning Approx. 3 HP positive displacement (PD) pump for bag cleaning at only 7- 9 PSIG. 1 HP direct drive gear motor for distribution arm, integral manifold/surge tank, pneumatically controlled firing mechanism activating the diaphragm valves/nozzles. When cleaning arm & bag segments are correctly aligned air nozzles fire directly into bags without wasted cleaning air. -- Includes: MAC FS24x24 AIRLOCK Rotary Air Lock (RAL) with approx. 2 HP SYNCROGEAR MODULE gear motor; sprinkler package; 60° Cone-shaped hopper attached to MAC at bottom of cone. -- Features: (1) Floor-standing Electrical control panel (shared controls) with MOTORTRONICS Solid State AC Softstart for main 150 HP motor. -- Additional Features: Explosion vents. Summer/Winter diverter and return air ductwork. Support structure. Caged access ladder from ground Service Platform and to the top plenum. -- Baghouse constructed of 7 gauge carbon steel containment; one piece body all welded construction, 180" (15') diameter shell panelized unit, walk-in plenum for maintenance and bag replacement. -- MAC design features: MCF 4HVP Pump package. MCF Medium-pressure air requires less HP and yet offers high dust and air collecting efficiency with unmatched baghouse cleaning at lower operating cost. MCF pulses each bag the same number of times with the same amount of air. (Unlike some competitors which clean the inside rows of bags more often than necessary thus wasting energy, causes uneven pressure drop, and bag wear). -- (2) of these identical units for sale are installed per photos, Material handling fan/drive is also common for both Unts. -- Overall dimensions: 580.5" high x178.5" square frame with an estimated weight of filter unit (less structure and accessories) 31,000 Lbs. -- Professional dismantling/rigging, truck loading and transportation are available at extra cost. -- NOTE: The right-hand unit is at forefront.. The left-hand unit is not as easily accessible.

MACDONAL STEEL - 26 PT: Dust Collector with RAL/Auger and Diverter Gate.Overall data: 16,700 CFM; 1,780 sq/ft. of cloth area comprised of: (85) Bags: 8" Dia. & 120" long; 60 HP blower; 26" inlet dia. with retrofitted Auger/Rotary Air Lock. -- Equipped with: Electrically operated mechanical bag shaker; back pressure damper on inlet manifold; Diverter/Abort Gate. -- Complete with: Safety hoop access ladder; (1) access platform to filter media; (1) top mounted fan/motor; silencer on return air. -- Starter/electrical control panels and disconnects inside/outside for each drive. -- Used 150 HP; rated VFD is available at extra cost.

MACDONALD STEEL 65 ST Dust Collector System with Shaker filter cleaning, Rotary Air Lock, and 18' dia. housing. -- Specifications: Capacity for 65,000 CFM, 18' dia. shell, with 8,199 sq-ft. of filter area for an air-to-cloth ratio of 7.7:1. T-150 polyester bags 14 oz. with a 30 - 40 CFM.@ 1/2" WG permeability. -- Current Fan configuration: System 1: Fan inlet of 33" at 32,500 CFM; System 2: .Future capacity for a second fan as per System 1. Return air duct is 42" x 72". -- Filter Cleaning: Top mounted electrically operated & timed mechanical shaker, approx. 2 HP motor which will automatically operate on all shutdowns. -- Equipped with: MACDONALD 18" Rotary Air Lock (RAL) with bottom eductor/T-section for connection to a relay/transfer fan (not included.). -- Complete with Fire Damper, Summer/Winter Damper with Silencer, Explosion doors, safety ladders, and access platform. -- Features: 13" MH/HT 20 HP Transfer/Transport fan -- Overall height is currently 57'-3" with 12' clearance under RAL. Weight of filter with structural steel is 29,000 Lbs plus fan is about 3,000 Lbs. -- Shell panelized construction (made of separable panels allowing for road/Hwy travel).Professional rigging, loading and transportation are available at extra cost; quote upon request.

MARATHON SE-503042-830 Side Eject Closed Door BalerSpecifications: -- Side eject type. -- 30 HP motor. -- Feed opening 50" x 28". -- Bale 30" X 42" X 72". -- Shipping weight 15,200 lbs.. -- LOADED ON YOUR TRUCK

MARATHON RJ-450 Stationary CompactorSpecifications: -- (4) Cubic Yard compactor. -- 15 HP motor. -- 6" Cylinder. -- Clear top opening 67.5" x 60". -- Left Side Loading Hopper. -- Driver Jog Control Station. -- Unit has been taken out of service for 2 years and stored inside.

MARATHON - Gemini : Horizontal Closed Door Baler (Full Pen) Specifications: -- Bale size: 30" x 48" x 60". -- Charge box: 35" x 60". -- Cylinder: Dual 6". -- Main motor: 20 HP.

MARATHON 604242-830 CLOSED DOOR HORIZONTAL BALER With Infeed Conveyor -- 8" Cylinder -- 30 HP Motor -- Feed Opening 60" x 42" -- Loaded on your Truck -- Infeed conveyor 48" x 31' - Can be sold separately for $14,950

MAREN 72/48-312 CLOSED DOOR HORIZONTAL BALER Specifications: -- 20 HP motor -- Feed opening 42" x 30" -- 7" Cylinder -- Bale size 72" x 42" x 42" --The Maren 72-48/312 Closed Door Horizontal Baler is a reliable piece of equipment suitable for various recycling and trash management applications. It features a robust 20HP power unit operating at 240V, which ensures efficient processing of materials. The baler is equipped with a 7-inch cylinder, providing substantial compaction force for effective baling.

MATH-EX (6) Position (Person) Basic Recycling Sort Line Specifications: -- 16 Feet x 32" Inclined feed conveyor with 48" high hopper and 2" high cleats @ 36" centers. -- 36 Feet x 32" Sort conveyor with infeed transition guides and Belly rest skirt one side. -- Sort platform with OSHA stair and handrail. -- (6) Sort chutes with 52" of clearance. -- 1-1/2 HP, 460 volt, 3-phase drives. -- (2) VFD Controllers mounted in control panel -- Pedestal style stand. -- Emergency pull cord stop or-E-stop for sort conveyor -- Motor wire and flex conduit for (2) conveyors shipped loose. -- (1) 6" Diameter Ceramic Drive Pulley -- (1) Stainless steel Back ChuteOptional Equipment: -- (2) VFD Controllers mounted in control panel -- Pedastal style stand -- Emergency pull cord stop or E-Stops for sort -- More wire and flex conduit for (2) conveyors

MATTEI BLADE 7 LX-TM-SE, 10 HP Tank-Mounted Rotary Vane Compressor w/Refrigerated Air Dryer ( 39 CFM @ 115 PSIG) RELIABLE ROTARY VANE AIRENDSBLADE features proprietary single-rotor stator unit (RSU) that incorporates MATTEI's legendary white metal Babbitt bushings on the back and now an oversized radial ball bearing on the front to address the side load created by the belts. MATTEI BLADE compressors are engineered for 24 hours/day service with exclusive Meehanite® iron blades, designed to last 100,000 hours.Features: -- MATTEI BLADE Series Air Compressors combine vane technology with dual "V" belt transmission to provide industry leading performance at affordable prices. -- As quiet as 61 dB(A), with speeds as low as 1,050 RPM, and operating pressures from 115 PSI to 175 PSI, BLADE is the ideal solution for small woodworking cabinet shops and manufacturers, body shops, mechanical shops, and other manufacturers.Equipped with: -- 10 HP TEFC motor, 39 CFM @ 115 PSIG; full-voltage motor starter, air-cooled Aftercooler, MAESTRO XB controller with Continuous and Automatic operating modes with standard load/unload operation on all models; MATTEI Rotor Oil 8000 F2 synthetic oil.Includes: -- 80-Gallon ASME Air Receiver Tank; Refrigerated Air Dryer, Pressure Gauge, Safety Valve, Filter, Oil Separator.

MAX-PAK MP 60 HD-15 Vertical BalerSpecifications: -- 15 HP Motor --Nominal Bale Size 60" x 30" x 48" --Bale Weight Up to 1000 Lbs OCC --Platen Pressure 40.91 PSI --Average Cycle Time 49 Seconds --Loading Height 54-1/2" --Ejector System Semi-Automatic --Full Bale Switch Standard

MCDONOUGH Bandmill 62″ Bottom Wheel.9-1/4" Face, 1-3/8" thick.