2019 CEFLA, model ROC 3 D. Reciprocating Spray Machine:This sprayer can easily run at 30 feet per minute Machine consists of --a tilt-able up infeed belt conveyor with the Electronic Reading bar located over the entire width, this bar reads the parts as they enter the machine which controls the Gun spray pattern. --Parts are fed through the spray cabin by means of a Patented continuous CFB belt conveying system. --Sprayer is equipped with (2) two roll Overspray recovery systems. Belt cleaning is done by means of a counter-rotating roller's with scraper and belt cleaning unit. The rollers are fitted on the "cleaning" trolley which is pulled out from under the machine longitudinally by manual control. Motorized outfeed belt conveyor, tilt-able up to make access to the cleaning trolley easy. -- (2) Oscillating arms equipped to accept a maximum of (8) guns, driven by a Brushless motor's, the PLC in the control panel automatically triggers the guns based on thier size and location on the belt. -- This sprayer has (2) two separate lacquer feeding circuits and a pressurized cabin with both incoming air filtration and exhaust filtration. -- Air is pulled in from (2) air intake ducts (positioned between guns) above the slanted perforated top panels, perforations help to reduce turbulence -- Large front viewing window/access panel.

CEFLA KLEENSPRAY 12 Reciprocating Spray Line;The "Kleenspray 12" Reciprocating Automatic Spraying system is mainly based on the use of a closed continuous CFB belt conveying the panels to & through the spray area. The design has many advanced mechanical solutions to allow considerable advantages.KLEENSPRAY Technical Features: -- Non pressurized spray cabin, "Paper Belt Overspray Capturing" lacquer system; microprocessor unit for spraying operation control. -- 5-Edge coating, 51" max. width, 76" long spray enclosure. -- Gun Carrier: Reciprocating-type linear Gun Carrier with (4) guns; includes (1) station with "(4) guns, stainless steel material handling pumps", clamps & brackets for free height and angle settings. -- Supporting trolleys driven by toothed timing belts with brushless motor with electronic control, reciprocating slider, automatic reversal of gun angle on each stroke to cover panel edges, with variable speed; (3) lacquer feeding circuits. -- Light barrier gun control: Photo cell sensors send material size to the programmable controller which opens and closes the guns. -- Conveyor System: "Paper Roll" continuous collection belt with rollup collection paper area, with long life and easily removable infeed roller section with electronic reading barrier consisting of (60) photo diodes and outfeed roller. -- Booth Enclosure: Made of sandwich paneling with glazed elements; port for access to the spray guns units. The machine is particularly suitable for the application of waterborne drying lacquers; these products assure minimum environmental impact. Please Note: (4) Spray guns & (2) pumps are included.Line Includes. -- VENJACOB Oven following the KLEENSPRAY. 600V/3/50-60 Hz. 230Vac/24Vdc. Control Voltage Max capacity 25 KW. Nominal Load 40 Amps.Year of Construction 2001. S/N 20104593 -- BURKLE UV Curing oven following the oven. Type TRUV2. (2) UV Lamp. Electrical 600/480V/360 Hz Control Voltage 24 Vdc. Nominal Power 49.5 HP.Nominal Current 99.8 Amps. S/n 010458-01. -- Pumps and pneumatic components. -- The panel cleaner shown at the start of the line is NOT INCLUDED.

CEFLA EASY 2000D Reciprocating Feed Through Sprayer and Vertical Oven Finishing Line:This line is still in operation with the original owners, it have never run full time, there are weeks when it is 1 day per week. It is recommended with a line of this age to do a full recondition prior to or as it is being installed. If that is not possible, it is still running and can be seen that way. CEFLA Complete 52" (1,300 mm) Finishing Line with: SORBINI Panel Cleaner, "EASY D 2000 W" Reciprocating Sprayer, Conveyor(s), and CEFLA Hot Water Vertical Oven. The line is composed of the following:001) Belt conveyor CEFLA "TN 2500"002) Panel cleaning / brushing machine SORBINI "VS 33"003) Automatic spraying machine CEFLA "EASY 2000 DRY SYSTEM" with pressurized cabin004) Transfer conveyor005) CEFLA PIEFFE PF2 VL/6 7500 pass through oven006) Vertical Oven, (3) chambers with belts CEFLA "VN 2000"007) Unloading Conveyors

DISA NFK 9 - 2BL Modular Dust Collector. Up to 45,000 CFM @ 6.25 to 1 air-to-cloth ratio, and @ 11.6" w.g. external static pressure; modular, expandable Heavy Duty Baghouse. -- 7,200 Sq/ft of filter area, mad up of (450) filter bags. -- Filter consists of (9) Filter module sections with access door in each section and (2) blank inlet module sections with (9) 2 HP regeneration fans for cleaning of filter media and (2) blank entry modules. -- Comes with: (1) 60 HP Belt drive COMBIFAB blower package w/drive guards; motor & fan are a common steel base/frame with ground level installation. Fan delivers about 20,000 CFM. There is sufficient filter capacity for at least 75 - 100 HP second fan/motor. -- Complete with: Outside separate elec disconnects for each cleaning fan. -- "NRS-10" Rotary air lock for bottom discharge with 2 HP TEFC motor; Steel support members dismantled.. -- Includes: Some outside pipe (and main headers explosion/access doors -- Note: (2) cleaning fans are missing and will be supplied at cost. -- Actual model is NFK2000 9+2 BL HJLR.

DISA CS-4 MAXI Dust collector with Rotary Air Lock. Approx. 16,000 CFM at 8.7:1 air-to-cloth ratio; 1,725 sq. ft. of filter area, with (128) filter bags filtering to 3-micron. -- General Info: CS-4-M consists of (3) filter modules & one entrance module. -- Comes with: DISA, S56-500 Material Handling fan powered by 50 HP TEFC motor. Fan nominal rating: 16,000 CFM @ 9" SP. Fan is currently mounted on elevated support but can be installed on the ground as well. -- (3) Reverse air bag cleaning modules with motorized fans that clean the bags every (4) hours of operation automatically, each with 2 HP fan motor. A damper at inlet closes during cleaning cycle to prevent blowback. -- Complete with: Hopper bottom as collected dust is conveyed to one end where a NRS-20 Rotary Air Lock where dust is discharged into Transfer fan. Filtered air return unit, 8' support structure to allow for dumpster under Dust Collector. -- Includes: Control panel, motor starters and switches, and Explosion Panels. Material handling main fan w/motor mounted to side of base module. -- 26" diameter inlet pipe, 97" clearance under collector for dump hopper, free standing steel bolt-together structure, -- Features: Dust transfer from bottom of Rotary Air Lock to enclosed container by separate floor mounted material handling fan, approx 7.5 HP. -- Note: Pictured storage bins are not included.

DONALDSON / TORIT - 2DF-16, ...Cartridge Dust CollectorSpecifications: -- Holds (16) cartridge filters. -- Includes "New" AirMax Premium Media Cartridge Filters: Fire retardant. -- Total filter media area: 3,616 ft². -- Air-to-Media ratio @ 8,000 CFM is 2.2:1. -- Automatic Pulse Clean System with: Differential pressure gauge and sequencing control in enclosure. -- (2) Hopper outlets with sealing drum cover kits. -- Steel support structure. -- Includes: 20 HP Top mount, direct-drive Blower. -- Rated for 8,000 CFM. -- Electrical motor starter & controls. -- Includes: Installation/Operation/Maintenance Manuals.Sold with 6-Month Mechanical Warranty

DONALDSON / TORIT DWST6-5 Cartridge Dust CollectorDownflo® WorkStations (DWST) fit anywhere on the plant floor and apply NO restrictions to worker movements or visibility. The full line of WorkStations are designed specifically for those in-plant areas where dirty and/or noisy operations are out in the open—grinding, sanding, chipping, batch mixing or welding. The DWST delivers exceptional performance in metalworking, woodworking, and process applications where high filtration efficiency and ledge less construction is often a requirement. Specifications: -- (5) Module System, each with 10 HP motor, 7,000 CFM. -- (4) Ultra-Web cartridges. -- Pulse-cleaning manifolds and ventures, (2) dust drawers. -- (1) Acoustical panel per module. Louvers mounted on lower section of unit.Includes: -- (1) IEC control panel includes 460-volt motor starters, circuit protection for each motor, transformer, programmable logic controller. -- Magnehelic gauge mounted in a panel door, start/stop buttons, and a through-the-door disconnect switch. -- Pulse cleaning can be continuous or after-shift. -- All components are IEC rated. The enclosure is rated Type 12. -- 1"; Compressed Air Regulator with Filter Separator and Gauge, Black Iron Fittings, and Black Iron Piping Required for Cleaning System. -- Provides a 1"; Common Connection Point for Design Shutters to Tie into with Existing Compressed Air System.

DOUCET DRAWER MASTER DWM-36 36" Universal Drawer Box Assembly Clamp Specifications: Assembles drawers with Standard Finger-Type Dovetails, Sliding-Type Dovetails, Bored & Doweled Drawers, and Tongue & dado box joints. Cap. 10" H x 24" W x 36" L. Equipped with: Fixed left jaw, Manually adjustable right jaw, with Rapid set jaw opening. Double-acting pneumatic cylinders. 2-Hand push-button operation. “Quick” Mode & "Progressive Compression" mode, Operates as a jog button to allow for easy fitting of bottom panel in lateral grooves. CURRENCY NOTE: Negotiable Price is listed in U.S. Dollars.

DOUCET BT3-30-5-23-G-PT Return Conveyor for Edgebanders Specifications: Right-hand feed, with Left-hand return. Min. part size 4" x 12". Max. panel size (with operator assistance supporting then turning panels) 45" x 96". Equipped with: 1-1/2’ L Infeed roller conveyor section, with (5) 23-1/4” W & (2) 34-1/4” W Rollers. 34-1/4” W x 5-1/2’ L x 35” H Receiving table, with Automatic/Manual height adjustment 2". (8) 3/8” Dia. transfer belts, (3) on 3” Centers, (2) on 6” Centers, & (3) on 9” Centers. 29-1/2” W x 5-1/2’ L x 34” H Return table. 29-1/2” W x 18’ L x 34” H 3-Section Return conveyor, with 5-1/2” W x 6’ L Gravity roller conveyor side extension. All rollers 1-7/8” Dia. covered line shaft on 3” centers. CURRENCY NOTE: Negotiable Price is listed in U.S. Dollars.

DOUCET FX 150 Automatic Feed to Finger JointerModel "MT-10-GD" automatic feed to Finger Jointer, chain feeding system driven on the bottom and right-and-left sides, feeds boards up to 6" max. width. -- Model "FX-150" right-hand Shaper section: Cap. 3/4" - 2" max. thickness, 1-1/2" - 8" max. width (with lugs on 12" centers, 6" max. width on 9" centers), 5" min. - 96" max. length. -- Equipped with: 5 HP Trim saw, 15 HP Shaper motor, PLC controls on shaper section, dual feed chain with lugs on 12" centers, 45 FPM fixed feed speed, 5 HP feed drive, PLC controlled extrusion type glue applicator with 12-gal. tank, sound enclosure and cabinet type base. Transfer to the assembly press. -- Includes: Stainless friction plates on assembly table, board holddown on all (4) sides, sound enclosure, cabinet type base and all protective hoods, (1) 8-bolt cutterhead with knives and setup stand. -- Approx. 8,000 linear ft./shift or more based on 12" average infeed length.This unit has no control panel

DOUCET - RDM2: Door Master Rotary Door Clamp with (5) StationsMax. cap. of 30" x 96" per squaring assembly. -- Features: Double door clamp design; allows clamping & squaring multiple doors at one time or large doors up to 96" L. -- Machine offers: Precise & accurate squaring of stile & rail cabinet doors; with the rotating design, you can achieve high production.Equipped with: -- (5) Rotating pneumatic sections. Each section with pneumatic squaring assembly: (2) Horizontal; (4) vertical clamps. -- Push button control for: Rotation with Heavy-Duty 575 - 3-phase gearmotor drive. -- Made of 100% welded tubular steel construction.Actual model is: DOUCET "RMD2-5-30-96".

DOUCET - 16-SECTION: Clamp Carrier (Hydraulic)Specifications -- (16) Sections; 8-1/2' width. -- (6) Clamps per section; (86) clamps total. -- 32" Clamp opening (rapid change) with: 2-1/2" High jaws.Complete with: -- 5 HP Hydraulic power pack and motor for rotation. -- Hydraulic clamp tightening. -- Pneumatic overhead panel flattener.NOTE: Tear down included!

DOUCET - 8-SECTION, ...Clamp Carrier (Hydraulic). -- (8) Sections, 8-1/2' width. -- (8) Clamps per section, (64) clamps total. -- 42" Clamp opening (rapid change) with 2-1/2" high jaws. Complete with: -- (1) Pneumatic fence w/manual valve. -- 5 HP Hydraulic power pack and motor for rotation. -- Hydraulic clamp tightening; mounted on rail. -- Pneumatic overhead panel flattener.Actual model is: SRH 08-8.5-64-42R.Note: Tear down and loading not included.

DOUCET - DRAWER MASTER DWM-36: 36" Universal Drawer Box Assembly ClampSpecifications -- Assembles drawers with: Standard finger-type dovetails; sliding-type dovetails; bored & doweled drawers; tongue & dado box joints. -- Capacity: 10" H x 24" W x 36" L.Equipped with: -- Fixed left jaw, manually adjustable right jaw; Rapid set jaw opening. -- Double-acting pneumatic cylinders. -- 2-Hand push button operation. -- “Quick"; Mode & "Progressive Compression" mode; operates as a jog button to allow for easy fitting of bottom panel in lateral grooves.

DOUCET SDM-M-30-72 Frame and Cabinet Door ClampDesigned for quick and accurate clamping & squaring of miter and regular cabinet doors.Specifications: -- 5-1/2" x 12-1/2" Min. door size, 30" x 72" max. door size. -- (1) Fixed vertical clamp, (2) mobile vertical clamps on roller bearings for effortless positioning. -- (1) Mobile horizontal clamp with a unique "gas spring" assisted lever for effortless centering; pressure is distributed with 4' dia. air cylinders. -- "Progressive Flow" clamping system @ 80 PSI; 675 Lbs of clamping pressure per clamp; operator working height adjustment.

"NEW" Doucet RC - STOCK Gluer - Table top unit for glue applications on a smaller scale. Motorized stainless steel roller equipped with a 2 Litre capacity reservoir easily removable for clean up. -- Spread roller: Stainless steel with roller dimension 8" X 3 1/2"; speed of roller 50 FPM. -- Table top dimension: 20-1/2" x 13".

DOUCET MFE 300 Lateral chain feeder for moulders and optimizers -- 3'0" x 16'-0" working deck for material length 2'0" - 16'0"; width 2" to 9.5" and thickness 1/2" to 4". -- Feed system: Hydraulic variable speed 50-300 FPM with a 20 HP power unit. In-feed (4) roller accelerator; (2) top steel rollers and (2) bottom drive roller. Additional idler rollers along feed fence to support lumber during feeding. -- Chains: Transport length of lateral chain feeder 3'0". (8) strands of C2060 chains on pneumatic up/down device to release lateral pressure on board when feeding. -- Pedestal: Feeder controls mounted to pedestal with extended cable. Interface relay to stop feeder when moulder is stopped. -- Adjustments: Tool less adjustment handles for quick setups. Easy access to for thickness adjustments at front side of feeder. -- AVAILABLE OPTIONSOne (1) set of four (4) feeding wheels made of steel with hardenedsurface teeth $ 1 000.One (1) set of four (4) feeding flat wheels made of steel, 2" wide insteadof 1" for wide material feeding $ 500.One (1) set of four (4) feeding flat wheels made of steel 1" wide $ N/C.Guiding Tunnel between feeder and moulder,Standard Guiding Tunnel (4' long) $ 1 650.Standard Short Guiding Tunnel (32" long) $ 2 100.Complete Guiding Tunnel (4' long) $ 2 700.Complete Guiding Tunnel with adjustable fence (4' long) $ 3 800.Motorized Guiding Tunnel (4' long) on request.Additional chain transfer length capacity (up to a maximum of 6additional feet) For MFE-300-16 sold per foot $ 1 685. Note: More than 6 add. feet: price upon requestSteel plates between chainsFor MFE-300-16 $ 1 050.Platen chains recommended for softwood speciesFor MFE-300-16 $ 2 850.One (1) additional chain for shorter material down to $ 1 750.18" min. lengthPressurized lateral guide with roller bearing end $ 1 400.Powered lateral guide with roller and side guides on request.Custom working height on request.

DOUCET 12-SECTION Clamp Carrier (Hydraulic)Specifications: -- (12) Sections, 8-1/2' width, -- (9) Clamps per section (108) clamps total, -- 36" Clamp opening (rapid change) with 2-1/2" high jaws.Complete with: -- 5 HP hydraulic power pack and motor for rotation -- Hydraulic clamp tightening; -- Pneumatic overhead panel flattener.Note: Tear down not included

DOUCET ERS-96/RS-75/AP-508 MULTI-BLADE PANEL GROOVE/RIP SAW SYSTEM:The Doucet ERS-96/RS-75 Automated Panel GROOVE/RIP Saw System is designed to GROOVE and/or RIP panels as well as edge the sides of core materials. Ideal for plywood, OSB, MDF, HDF and other composite panels.This Line was originally designed for Engineered Flooring Blanks.ERS-96 Grooving Specifications:40 HP - 3,500 RPM belt driven saw arbor motor. Material width cap. 96" maximum. Material thickness 0.5" - 0.625" maximumGrooving pattern on 4" centers across the 96" width of panel. Depth and width of groove approx. 3/16" kerf/width by 1/8" deep.3" dia. Arbor shaft with 1.5 HP motor for motorized arbor adjustment for panel thickness. Saw arbor accessible from above for tool changes. -- Feed system:5 HP - 1,750 RPM feed motor, variable feed speed up to 75 FPM.(4) Powered bottom feed rollers & adjustable top idler pressure rolls with positive panel support during grooving operations.Top & bottom feed rollers have slip resistant urethane covered rollers, feed rollers are chain driven with air tensioning. -- Complete with:Dynamic saw arbor brake; Infeed anti-kickback fingers; Saw blade safety interlock cover; 12" dia. dust collection outlet (4,000 CFM required). RS-75 Ripping Specifications:40 HP - 3,500 RPM belt driven saw arbor motor. Material width cap. 60" maximum. Strip width cap. 2.5" minimum. Depth of cut 0.25" - 0.75" (6 - 19 mm) maximum.3" dia. Arbor shaft with 1.5 HP motor for motorized arbor adjustment for panel thickness. Saw arbor accessible from above for tool changes. -- Feed system:Doucet AP-508 Automatic panel feeder with scissor lift to automatically feed panels as needed.5 HP - 1,750 RPM feed motor, variable feed speed up to 75 FPM.(4) Powered bottom feed rollers & adjustable top idler pressure rolls with positive panel support during grooving operations.Top & bottom feed rollers have slip resistant urethane covered rollers, feed rollers are chain driven with air tensioning. -- Operator Interface: Doucet OI/HMI Control System for automatic loading & stacking with minimal human intervention other than a forklift operator to bring in new material and remove the processed parts/strips. -- Complete with:Dynamic saw arbor brake; Infeed anti-kickback fingers; Saw blade safety interlock cover; 12" dia. dust collection outlet (4,000 CFM required). -- Options Include: (1) Doucet AP-508 Automatic panel feeder with Indexing scissor lift. (1) Cross Transfer Chain Conveyor to feed panels sideways by the long edge through the Groover, max width 96". (1) Cross Transfer Chain Conveyor to feed panels short end wise through the panel RIPSAW, max. width 60" (1) Outfeed Lift Table to automatically stack ripped strips. Maximum weight of stack: approx. 5,000 LBS. -- Actual Model is DOUCET RS-75/ERS-96/AP-508

The Dubois SP-12 Linear Spray Machine is an automated linear finishing machine that can be used for a variety of applications including priming, staining, sealing, lacquering, etc. of linear stock. This spayer comes with (3) three arms, (3) three guns and (1) one paint pump. The guns are Binks spray guns Model 363, and Binks pump.Compatible with both waterborne and solvent based coatings --Three adjustable gun arms --9’-0"; long variable speed live roll conveyor w/ electric powered drive --Pneumatic gun trigger mechanism to automatically trigger guns on/off --Infeed guide fences --Top roller hold-down on infeed table --Ability to enable/disable individual guns --Easily cleaned spray trough --Adjustable atomizing air pressure --Adjustable fluid pressureIncluded optional features: &#9679 Stain wipe station mounted to outfeed with stain wipe brush &#9679 Exhaust system with spray enclosure, exhaust fan, & exhaust filter system &#9679 Denibbing station mounted to infeed