BELFAB LW3-10 Modular Dust Collection System w/ HUMMER BlowerSelf-contained patented modular designed unit for interior use; Specifications: -- 10 HP, 1,800 RPM and 4,600 CFM, HUMMER Blower, 12" inlet -- Heavy Duty sheet metal constructed plenum between the top bags and bottom dust collection. -- 126 Sq. ft. total cloth filter area. Non-sparking Heavy-Duty cast aluminum impeller.Equipped with: -- (3) High Efficiency 1/8" thick needle felt cloth bags up and (3) plastic collection bags down (includes set of 24" long extended machine legs to maximize collection capacity). -- Includes: Wired Magnetic starter 460V or 230V, 3-Phase.NOTE: The "LW" series can be specifically customized for current and future Dust Collection requirements as required by adding Filter Modules, a larger blower and inlet.

BELFAB NBM5-25 TILT TRUCK Modular Dust CollectorPatented Modular Technology; 7,500 CFM with a static pressure of 10"; designed for current need that can easily be upgraded, as required. -- Exterior design; each "NBM" filter module with (1) service door & (1) explosion door per NFPA 68 safety regulations, this unit has (5) filter modules.Specifications: -- Each "NBM" filter module with: (18) 7" x 60" poly twill filter tubes. -- Direct drive centrifugal fan assembly with: HUMMER 25 HP @ 1,800 RPM High Efficiency TEFC blower motor, UL & CSA approved; AMCA Class-C anti-spark blower assembly with Heavy Duty steel impeller. -- 18" In-let dia., 660 sq. ft. filter surface area. Control Panel & Shaker mechanism includes: -- (2) Interlock magnetic starters, (1) for the blower motor and (1) for the automatic shaker mechanism. -- Adjustable timer, pilot lights all pre-wired. -- Includes: (5) Heavy Duty plastic tilt trucks on rollers for disposal of waste. -- Options available, but not included are: Spark detection/fire suppression system, Fire & abort damper, 2-Way valve, Explosion vent conduit; ...please ask for quote.CALL FOR PRICING

BELFAB LW6-15 Modular Dust CollectorSelf-contained patented modular designed unit for interior use with direct drive 15 HP - 3,600 RPM motor, 5,000 CFM centrifugal fan assembly @ 7" static pressure, standard blower. -- 14" Inlet -- The "LW" series can be specifically customized for current and future Dust Collection requirements as required by adding Filter Modules, a larger blower, and inlet. -- Heavy Duty sheet metal constructed plenum between the top bags and bottom dust collection. -- Equipped with: (6) High Efficiency 1/8" thick needle felt cloth bags up, 210 sq. ft. total cloth filter area. Non-sparking Heavy-Duty cast aluminum impeller. -- Includes: Wired Magnetic starter for 208/230/460/600 V. -- Additional options available

BELFAB LW6-15 Modular Dust Collector (HUMMER)Self-contained patented modular designed unit for interior use with direct drive 15 HP - 1,800 RPM motor, 5,000 CFM "HUMMER" centrifugal fan assembly @ 7" static pressure, standard blower. -- 14" Inlet -- The "LW" series can be specifically customized for current and future Dust Collection requirements as required by adding Filter Modules, a larger blower, and inlet. -- Heavy Duty sheet metal constructed plenum between the top bags and bottom dust collection. -- Equipped with: (6) High Efficiency 1/8" thick needle felt cloth bags up, 210 sq. ft. total cloth filter area. Non-sparking Heavy-Duty cast aluminum impeller. -- Includes: Wired Magnetic starter for 208/230/460/600 V. -- Additional options available

BELFAB RPJ26-121 Pulse Jet Dust Collector with Rotary Air Lock and Transfer Fan.Specifications: -- 15,285 CFM approx. baghouse dust collector with (121) filter bags at 10-feet long with metal cages. Total of 1,884 sq. ft of cloth area. -- Filter Cleaning: Reverse Pulse Jet (RPJ) via plant compressed air that is sequenced by diaphragm valves/solenoids/manifold thru to a Venturi that injects a burst of air pressure to dislodge the dust build up on the outside of filter bags. This is a continuous process during the operation of the dust collector. (no shut down is needed). -- Main Fan: 75 HP side-mounted blower motor. with approx 26" dia. inlet. Rated at approx 15,000 CFM @ 15" SP. -- Comes with: Main starter with control panel. -- System includes: Relay/Transfer fan, steel structure support stand, low height as waste is transferred by fan, safety ladder/platform, safety railing, and approx. 20" Rotary Air Lock. -- Housing is about 8'-5" square by about 23' high overall. Weight with structure is about 8,600 Lbs. Note: Round cone section with storage capacity of about 246 cu ft may not be included. in above height and weight.

BELFAB - LW2-5Modular Dust Collector --Self-contained patented modular designed unit for interior use. The "LW" series can be specifically customized for current and future Dust Collection requirements as required by adding Filter Modules, a larger blower and inlet. -- Heavy Duty sheet metal constructed plenum between the top bags and bottom dust collection; rated at 2,500 CFM with 7.2" static pressure w.g. -- Equipped with: (2) High Efficiency 1/8" thick needle felt cloth bags up and (2) plastic collection bags down (includes set of 24" long extended machine legs to maximize collection capacity), 70 sq/ft total cloth filter area. -- Complete with: Direct drive centrifugal fan assembly with 5 HP TEFC motor (inlet can be mounted top, bottom, left or right to facilitate ducting), non-sparking Heavy Duty cast aluminum impeller; 7" inlet dia. and pre-wired magnetic starter.

YM-800 1 YARD 4 OR 5 TINE Orange Peel GrappleSpecifications: -- Operating Weight 2,400lbs -- Opening Width 71 1/8" -- 4 or 5 Tine in stock - Ready to ship -- Rotating -- Hanger for Extra Cost

--This machine is in an Auction on exfactoryauctions.com--NO RESERVE-- (2 Available) BIESSE SKIPPER 100 2-Head CNC Machining Center, with Infeed & Outfeed Tables – Seller states that machine was run (2) shifts from 2005 - 2021, then only a few hours per day since! Specifications: Flexible "Top & Bottom" Machining Center that uses an innovative panel handling system. Working Capacity: "X" Axis 3,000 mm (118.11"), "Y" Axis 1,000 mm (39.37"), Max. part thickness 60 mm (2.36"). Min. workable part size: "X" Axis 90 mm (3.54"), "Y" Axis 70 mm (2.76"), & "Z" Axis 8 mm (0.31"). Work Table: Left-hand infeed & Right-hand outfeed, Each with 20-1/2” x 66” x 35-1/2” H infeed & outfeed areas with Fixed caster-type conveyor rails. Positioning Speed: "X" Axis 120 MPM (393 FPM), "Y" Axis 90 MPM (295 FPM), "Z" Axis 30 MPM (98 FPM). Boring Units: (1) Top & (1) Bottom boring blocks, Each with: 3 kW (4 HP) Motor, Boring spindle speed 4,000 RPM, (29) Vertical spindles with (17) "X" Axis & (12) "Y" Axis, (10) Horizontal spindles with (4 + 4) "X" Axis & (1 + 1) "Y" Axis, & (1) "X" Axis Grooving saw with 3 kW (4 HP) Motor, Blade speed 5,000 RPM, & Blade diameter 150 mm (5.91"). Machining: (1) Top & (1) Bottom 3.5 kW (4-3/4 HP) Electrospindles, Each with: Variable spindle speeds 7,000 - 18,000 RPM, Right-hand/Left-hand rotation, HSK D-50 Adapters for Manual push-button quick tool change, ERC-32 Toolholders & RC-32 Collets. Operator & Machine Control: Mobile Control Console, with PC-Based Control, 18" LCD Monitor, BIESSE "WORKS" + "WINDOWS" Operating system. Pedestal & Pendant controls. Equipped with: Universal transformer, 200 - 600 V, 50/60 Cy, 3-Ph., Automatic lubrication system for guides & ways, Sound hood, 79" H Safety fence with Lock-out door, & TAPESWITCH "CONTROLMAT CKP" 24" x 72" Heavy-duty ribbed pressure-sensitive safety mat. Complete with: 7’ x 9’ x 35-1/2” H Infeed Table, with Rails & Pusher. 6-1/2’ x 8’ x 35-1/2” H Outfeed Table, with Transfer Belts. Handheld Bar Code Reader. Dust Manifold. Dimensions including Safety Fence: 307" x 184" x 98" H.

BIESSE AKRON 855 EDGEBANDER (W/PRE-MILL & CORNER ROUNDING):Specifications: -- Material infeed for strips & coiled edge material like PVC, ABS, veneer, and solid wood.0.4 - 3 mm (0.118"), Panel thickness 10-60 MM ( 0.39" - 2.36"), min. panel length 140 mm (5.5") and 85 mm (3.34") min. widthInfeed System Equipped with: -- Independent copying guide pads on each unit with manual adjustment & mechanical digital indicator.Pre-Milling Unit (FI-701) (2) 1.8 kW motors (2.5 HP), 12,000 RPM with Auto-Set device to ensure optimum positioning of the cutters according to the thickness of the panel being machine; -- "VC-710" edge feeding, gluing & pressing unit with automatic edge magazine for strip & coil stock; 3 mm PVC guillotine. -- "TEKNO-GLUE" System, Pre-Melt "QM-701" for quick heating & tank changing with floating & bi-directional glue roller applicator.Pressure Section: (1) Large motorized pressure wheel with clutch, plus (5) idle rollers, independent pneumatic pressure control & digital counters for quick edge thickness changeover.Edgebanding Workstations: -- Double Motor End Trim, tiltable from 0° - 15°, each motor 0.5 kW (0.6 HP) - 12,000 RPM; sliding in a slicing motion on a 45° precision guide bar with oversized bearing blocks. -- Top & Bottom Rough Trim: Top/bottom (2) motors, each 1.8 kW (2.5 HP) 12,000 RPM with superimposed motor position, 0° - 45° tilt capability, straight cutterheads (80 x 25 x 16 mm) w/insert knives; includes pneumatic exclusion from control panel. -- Top & Bottom Fine Trim: Top/bottom (2) motors, each 1.8 kW (2.5 HP) 12,000 RPM with superimposed motor position, 0° - 45° tilt capability, straight cutterheads (80 x 25 x 16 mm) w/insert knives; includes pneumatic exclusion from control panel. -- Multifunction 4-Motor Corner Rounding Unit "CR-202": (4) Motors, each 0.65 kW (0.87 HP) - 12,000 RPM; motors carry out Corner Rounding and Top & Bottom Trimming on panel edge with PVC, ABS, etc. material and wood edgebanding up to 5 mm max. edge thickness. -- Top & Bottom Radius Scraping (PVC): Knives R = 2 mm, with mechanical digital indicators for precision setup, pneumatic exclusion of the unit from the machining line, PVC scrape collection box. -- Top & Bottom Flat Scraper (Glue): self-adjusting with copy wheels & flat insert knives, removing potential excess glue before buffing unit. -- Top & Bottom Oscillating Buffing Station: (2) motors, each 0.37 kW (0.5 HP) - 2,800 RPM. -- Top & Bottom Hot Air Blowers is made by two 2000 W hotair blowers to reactivate the color of PVC/ABS edges after the machining.The air temperature is adjustableFeatures & Feed: -- All cutting & trimming workstations have HF motors and enclosed by padded sound enclosure, top pressure is provided by staggered double-row holddown wheels mounted on ball bearings. -- Feed chain track speed : 10 - 14 - 20 MPM (33 - 46 - 65 FPM). -- Complete with:CNi PC w/Flat, Color "REAL TIME" graphic interface design on 17"; flat screen (TFT) with high resolution. --

BIESSE ROXYL 6.0 EDGEBANDER (W/PRE-MILL & CORNER ROUNDING) + "AIR FORCE" PUR/EVA GLUING TECHNOLOGY: Features: -- Latest Technology combines productivity, efficiency, and flexibility for all types of edgebanding material."AirForce" emits high temperature compressed air through a slot nozzle directly onto the reactive layer of laser banding. That layer is activated and bonds the banding to the panel fibers.This technology allows changes based on banding colors without any setup. Environmentally friendly providing a “clean - green"; technology that eliminates glue and fumes, which becomes timely & important. -- In addition, it features a conventional EVA (Hot Melt) Gluing System to cover the full range of edgebanding processes in use today!Specifications: -- Edgebanding Capacity: Edge thickness for strips min./max. 0.4 - 22 mm (0.02" - 0.87"), coiled material from 0.4 - 3 mm (0.02 - 0.12"); panel thickness from 10 - 60 mm (0.39 - 2.36"), workpiece width min. of 85 mm (3.34"); workpiece length min. 140 mm (5.51"); feed speeds 10 - 14 - 18 - 20 MPM (33 - 46 - 59 - 65 FPM). -- Machine Controls: "Roxyl-Matic" Automated machine setup, MS/Windows XP Operating System, floppy drive, and 4 GB HD; USB port, keyboard, and mouse interface. -- Flat Screen (17") with color graphics interface: Programs can be easily created and recalled at will; Graphic interface makes programming easy; icons of each unit may be brought up on the screen to show the operator the status of the unit and the parameters, which can be programmed; Edgebander may be operated manually when required, without the necessity to write a program.Machine In-Feed Configuration: -- Pre-Milling Station "FL-502": (2) LH & RH Rotating NC controlled spindles with automatic center positioning. -- Edge Magazine: Automatic for processing coiled and strip edgebanding material + a (2) position vertical Coil Magazine Cart. -- Pressure Section: Servo controlled programmable pressure section with (1) large driven roller and (4) idle rollers.Gluing System: -- EVA (Hot Melt) "QM-705": Quick premelting granulate with glue roller applicator to cover conventional edgebanding material. -- AirForce "VC-710": High pressure, hot air system to reactivate special precoated edge material (commonly referred to as laser edge).Workstations: -- End Trimming Unit "IT90-S": Front & rear trimming motors, uni-point swivel 0° - 15° bevel, programmable pneumatic change-over from flush to bevel. -- Rough/Flush Trimming Unit "RS-100": Top/Bottom pre- or flush trimming motors -- Flush/Bevel/Radius Combination Trimming Unit "RF-400": Servo controlled, (4) Servo motors (one for horizontal tool position, one for tool up/down position); using combination bevel/radius/flush insert knives; pre-positioning of motors by pneumatic air cylinders. -- Anti-Adhesive "ADZ-700" Automatic Spray Unit with: Glue release agent preventing glue to adhere to workpiece's surfaces. -- Corner Rounding Unit "CR-202": (2) Motors for front/back corner a

BUSS M 4L 30" STRAIGHT KNIFE PLANER30" X 8" Cap., 20 HP direct drive top motor, 1.5 - 2 HP for dual feed speed, 4-knife round top cutterhead, sectional infeed rolls and chipbreaker. Complete with: Shaving hood, magnetic starters.

BUTFERING - Profiline SUR 313 RRR, ...Bottom Wide Belt Sander with Powered Infeed & Connect to Top Sander (...see SX-012684 - OPTIMAT SCO 413 RRRR, ...Top Head Wide Belt) Bottom 3-Head, 53" Width Capacity Wide Belt Sander.Head Configuration: -- 1st Head: Steel Contact Roll, 240 mm (9-1/2") dia., 22 kW (30 HP) motor. -- 2nd Head: Rubber covered Contact Roll, 65 Shore, 320 mm (12-1/2") dia., 22 kW (30 HP) motor; Rotation with or against feed direction. -- 3rd Head: Rubber covered Contact Roll, 55 Shore, 320 mm (12-1/2") dia., 18.5 kW (25 HP) motor; Rotation with or against feed direction.Features & Specifications: -- Outfeed Rotary Panel cleaning brush with: Abrasive grit, 5.5 kW (7.5 HP) motor. -- 950 mm (37") Section of free-standing power driven infeed roller track. -- 54" x 103" Abrasive belts, electronic abrasive belt tracking, and all heads with Servo driven grit compensation and motorized positioning. Abrasive belt Air Jet blowers on all heads. -- Vacuum conveyor belt feed with: Variable feed speed 5 - 25 MPM (16-1/2 - 82 FPM); automatic conveyor belt tracking; infeed & outfeed spring loaded rubberized holddown rollers; outfeed extension for linking to transfer conveyor, connecting Bottom head to Top head Sander. -- Constant pass line of 900 mm (35-1/2") by adjustment upper machine frame via (4) large dia. threaded spindles. -- Tie In conveyor: To connect to Top Head Sander; 1,500 mm (59"), 5 - 25 MPM (16-1/2" - 82 FPM), synchronized with machine bed conveyor speed. -- Color touch screen control with: (1,000) Programs, 1/8" - 5-1/2" motorized thickness adjustment; "quick-set" automatic thickness adjustment with LED readout; infeed panel "over-thickness" sensor.Complete with: -- Infeed & outfeed emergency stops; safety interlocks on all doors; roller infeed conveyor extension; motor load meters and electronic brakes for all sanding head motors. -- Operator and Maintenance manuals (in Spanish); spare parts drawings, spare parts list, and wiring diagram.NOTE: -- BUTFERING - PROFILINE SUR, ...Bottom Sander and OPTIMAT SCO, ...Top Sander are being offered as a "Complete System/Line" with Infeed & Transfer Connect; (1) Common Control for both machines to operate as a Line. Copy of original quote with detailed specifications is available upon request.Asking Price with this "SX-012681" listing is for the Bottom Head Sander only - Open to reasonable offers.

BUTFERING - OPTIMAT SCO 413 RRRR, ...Top Head Wide Belt Sander (...part of line with SX-012681 Profiline 3-Head Bottom Sander)Top 4-Head, 53" Width Capacity Wide Belt Sander with (4) Drums (Rollers).Head Configuration: -- 1st Head: Steel Contact Roll, 240 mm (9-1/2") dia., 22 kW (30 HP) motor. -- 2nd Head: Rubber covered Contact Roll, 85 Shore, 240 mm (9-1/2") dia., 22 kW (30 HP) motor. -- 3rd Head: Rubber covered Contact Roll, 65 Shore, 320 mm (12-1/2") dia., 22 kW (30 HP) motor; Rotation with or against feed direction. -- 4th Head: Rubber covered Contact Roll, 35 Shore, 320 mm (12-1/2") dia., 18.5 kW (25 HP) motor. -- All Heads with servo positioning of Contact Roller via precision motor to 1/100 mm, with possibility to store different values in the Terminal.Features & Specifications: -- Outfeed Rotary Panel cleaning brush with abrasive grit, 5.5 kW (7.5 HP) motor; 950 mm (37") Section of free-standing power driven infeed roller track; 54" x 103" Abrasive belts and electronic abrasive belt tracking; all heads with Servo driven grit compensation and motorized positioning; Abrasive belt air-jet blowers on all heads; Automatic head locking for fast abrasive belt change. -- Vacuum Conveyor belt feed with variable feed speed 5 - 25 MPM (16-1/2 - 82 FPM); automatic conveyor belt tracking, infeed & outfeed spring loaded rubberized holddown rollers. -- Constant passline of 900 mm (35-1/2") by adjustment upper machine frame via (4) large dia. threaded spindles. -- Color touchscreen control with (1,000) programs, 1/8" - 5-1/2" motorized thickness adjustment, "quick-set" automatic thickness adjustment with LED readout; infeed panel "overthickness" sensor.Complete with: -- Infeed & outfeed emergency stops, safety interlocks on all doors, roller infeed Conveyor extension, motor load meters, and electronic brakes for all sanding head motors. -- Operator and Maintenance manuals (in Spanish); spare parts drawings, spare parts list, and wiring diagram.NOTE: -- BUTFERING "PROFILINE SUR" Bottom Sander and "OPTIMAT SCO" Top Sander [SX-012681] are: Offered as a Complete System/Line with Infeed & Transfer Connect; one common Control for both machines to operate as line. - Copy of original quote with detailed specifications is available upon request.Asking Price with this "SX-012684" listing is for the Top Head Sander only - Open to reasonable offers.

BUTFERING E-LINE 213RL (2) Head Wide Belt Sander53" Width cap. Drum, Combinbation HeadHead Configuration1st Head : Steel calibrating contact roll 200mm Dia. 20 HP2nd Head : Combination Head 20 HP. ( Comes with (2) slide in platens, one for veneer, one for solid wood ) Rubber contact roll 140mm Dia. Specifications -- 53" x 75" Abrasive belts, -- Electronic abrasive belt tracking -- Conveyor belt feed with 2-speed motor, 18/ms, 2.3 HP motor, infeed & outfeed spring loaded holddown rolls, -- 1/8" - 5-3/4" motorized part thickness adjustment with LED readout.Equipped With & Features -- Infeed panel "over-thickness" sensor -- Brakes on both sanding head motors, -- Infeed emergency stop, -- Roller infeed conveyor extension -- motor load meters.

//This machine is in an Auction on exfactoryauctions.com// //Link to machine: http://exf.ac/i4s BÜTFERING E-LINE 313 RRL 1,350 mm (53.15") 3-Head Wide Belt Sander, with Combination Head Specifications: Variable feed speeds 2.5 - 13 MPM (8-1/2 - 42 FPM). Equipped with: 1st Head: 8” Dia. Grooved rubber-covered contact roll, with 22 kW (29-1/2 HP) - 2,930 RPM Motor. 2nd Head: 8” Dia. Grooved rubber-covered contact roll, with 18.5 kW (25 HP) - 3,535 RPM Motor. 3rd Head: Combination head, with 5-1/2” Dia. Grooved rubber-covered contact roll, 3-1/2" Dia. Smooth steel contact roll, 2-1/4" W Finishing platen, & 18.5 kW (25 HP) - 3,535 RPM Motor. All heads with Pneumatic belt tensioning and Infeed & Outfeed Pinch rolls. 53” W x 6-1/2’ L Feed belt, with 1.5 kW (2 HP) - 1,725 RPM Motor & 11” L Infeed extension with (2) 1-7/8” Dia. Rollers on 6” Centers. Control, with Control stick & LED Display for programmable thickness adjustment, and Motor load meters.

BÜTFERING SGO 211 RK Wide Belt Sander, 2-Head,(43") working width, equipped with (1) Contact Roller and (1) Combination head consisting of Contact Roller & Finishing Platen.Head Configuration1st Head: Rubber contact roller 160 mm (6.3") with 15 kW (20 HP) motor.2nd Head: Combination head with rubber covered contact roller and finishing platen, not segmented, 11 kW (15 HP) motor.Specifications -- Both heads use 1,120 x 1,900 mm (43" x 75") abrasive belts with electronic abrasive belt tracking. -- Feed system: Conveyor belt feed with variable feed speed 2,6 - 13 m/min (8,5 - 42 FPM), 1,1 kW (1.5 HP) feed drive, auto belt tracking. Part thickness 3 - 160 mm (0.1 - 6.3"). Automatic motorized part thickness adjustment with 0,1 mm LED readout.Equipped with and Features -- Electronic emergency brakes on sanding head motors. -- Infeed emergency stop. -- Motor load meters for supervision of stock removal. -- Roller table extension at infeed. -- Emergency stops at in & outfeed end. Automatic star/delta starters.

ONSRUD - W 200, ...Spindle Shaper Specifications: -- 5 HP Motor, endless belted drive to deliver 7,200 & 10,000 RPM spindle speed with reverse, -- 1-1/8" Spindle dia.; vertical adjustment 4" by handwheel, -- Foot pedal spindle brake. -- Table size 36" x 42". -- Long fixed side fence, custom installed. Complete with: -- Magnetic push button controls (upgraded).

CAIN - 360-10H, ...120" Front-Load Automatic Panel SawSpecifications -- 120" Cutting length; 18" diameter Blade.Equipped with: -- (1) 24" x 48" Infeed table; (1) 24" x 120" table with backstop.Dimensions: 228" x 180" x 66" H

CALPE TH5-1600 Heavy-Duty High-Production, Fully Automatic CNC Lathe: General Description: -- Multi-Spindle cutting simultaneously, (5) spindles using V-type gouge knives. -- 63" (1,600 mm) Max. distance between centers; 5-1/2" (140 mm) max. swing diameter between spindles. -- CNC Controlled with 2.95" (75 mm) travel for depth of cut. Motors/Speeds: -- Servo controlled CNC drives: -- CNC controlled electronic variable speed head drives the movement of the (5) gouge tools. -- CNC controlled feed speed carriage, variable up to 50 FPM (15 MPM). -- (1) Head stock variable speed drive for the (5) spindles, up to 6,000 RPM, approx 10 HP. -- Fast return travel of up to 590 IPM (15,000 mm/Min). 2 HP approx hydraulic drive -- Loading device & tail stock powered by hydraulic pump with 2 HP - 1,750 RPM motor; No. 5 Morse taper on main spindle shaft. Features: -- Automatic loading & unloading device; carriage mounted with linear guides providing high precision movement. -- Full CNC controller with on-screen CAD programming for all products.Matching CALPE L6-1600, record number LC-010996 spindle sander is available at additional cost at same facility.

CALPE L6-1600 Spindle Sander with Hopper Feed. -- (6) Spindles, semi-automatic sanding machine; distance between centers 63", 6-3/16" max sanding diameter, capable of sanding 1800 spindles per hour. -- 4 HP - 1,800 RPM head motor, (5) sandpaper holders, each for different grits, 4000-3200-2200-850 RPM head spindle speeds. Copier unit that follows all contours. -- Oscillating sanding units & stationary pick up of part. -- NOTE: This sander was running with lathe on our record number LC-01811 and owner prefers to sell at the same time.