D M C FINESAND 130 2PO WIDE BELT (50" - 90", 2-HEAD): -- Specifications:Orbital Pad Sander, designed for cross-grain scratch removal on style & rail frames; with (2) Orbital Platens & (1) Brush. -- Working Capacity: Width 51", height/opening 1/8" - 4-5/8", motorized part thickness adjustment with digital readout, (4) screw jacks rise & fall. -- Sanding Heads: (2) 10" Wide Platen heads with rubber surface for elimination of abrasive belt cross-grain scratches. Dual orbital action heads with (1) high speed orbit on sanding pad, powered by 5.5 HP motor, and a secondary "low RPM" orbit on head assembly (1.5 HP motor), superimposed over the high-speed orbit for fast cutting action. -- Rotating Cleaning brush on outfeed side. Abrasive material for Sanding Heads is 18" x 52" in size. -- Feed Conveyor: Variable feed speed from 6 - 40 FPM, inverter controlled by 5.5 HP motor; vacuum conveyor bed with 15 HP blower motor. -- Complete With: - Digital height readout. - Infeed and outfeed rubber coated hold-down rolls. - Infeed hand safety stop bar, emergency e-stop. - Star-Delta motor starter. - (2) Dial indicator motor load meters.

SCM / DMC MB 90 WIDE BELT (50" - 90", 2-HEAD): -- Specifications:This machine has been designed to house and combine working units equipped with oscillating discs and brushing rollers, suitable for different sanding applications. -- Working Capacity: Width 53", Main Working Units 1-2-3 -- Oscillating Discs Unit: (19) -- Brushing Unit: 300 mm diameter -- Feed Conveyor: from 2 to 16 m/min -- Complete With: Variable feed drive and vacuum feed table.

DANCKAERT - 44 , ...ResawAir Strain 44"; x 5"; Bandsaw.Features & Specifications: -- McDONOUGH Center Split Feed Works. -- Wheel is supported on both sides - not cantilevered. -- Pressured guides. -- McDONOUGH Infeed Rolls. -- Max. Cut: 14";. -- New Dynamic brake. -- 60 & 100 HP. -- Control Cabinet (has battery backup and resistors to prevent spikes). -- Infeed & outfeed systems are the same. -- 24 ft. Long Camel Back chain (has air bags that are controlled by photo cell to raise & lower and index 1-board at a time). -- Max. length of lumber: 24 ft.From Seller: "The machine has a new VFDD 100 HP and a new WEG Severe Service 60 HP motor. All new hydraulic motors, caramel back chain, and roll cases."NOTE: Needs hydraulic unit.

DEIMCO MFM-98 ACRYLIC COATING FINISHING SYSTEM: Drying Oven for the purpose of baking and drying the acrylic finish onto lumber and panel products. -- Specifications:3"; dia. x 21.625" long Rollers on 12"; centers; Infeed: 16' long In-feed Conveyor, 10' long Transfer Conveyor, 12' long Oven Conveyor: -- Operator & Machine Control:Built with Allen Bradley/Honeywell Components, MFM Serial: 1177, Voltage: 460V/60 Hz/25 Amp, Air: 1"; NPT 90PSIG. -- Complete With:Electrically Heated Oven; 8 Cool Down Fans; 2 - Hydraulic Lift Tables; Panel Machine with Hydraulic Pump; 15’ Flash Off Conveyor; 40’ Cool Down Conveyor Includes the following for (two) flood coat machines, Conveyor System, Arbors, Paint Pump, Hydraulic Pump, Hydraulic Lift Table -- Complete Over-all Foot Print 175’ long x 50’ wide

FELDER - KF 700S: Sliding Table Panel Saw, Spindle Moulder, & ShaperSeen: Little use; perfect working order, and Conditions! -- Motors Rated: 5.5 kW with: DELTA START; electric height adjustment of saw & spindle Moulder; scoring unit with: Separate motor; spindle fence plates with: Safety bar guides. -- Dimension sliding table: 2,800 mm; Precision miter guide with: Cutting length compensation; remote "On" switch on: Sliding table; tilting bracket for power feed; FELDER "F38" Power Reed & table extension.

FERGUSON 2' x 18' Cold Press - Pneumatic27" x 218" End loading segemented air hose press with Motorized Daylight opening with up to 60" of daylight. -- (3) Individually actuated, 27" x 96-1/2", 27" x 25", 27" x 96-1/2" segmented platens. -- Equiped with: (2) Rows of pop-up rollers in lower platen for easy loading/unloading of the press.REBUILT IN 2017 - NEW HOSE & ENDS, NEW SHEAVES W/ CABLESCan Press BEAMS, DOORSTILES, LAMINATE GARAGE DOOR PANELS, Etc.

FIN - ST 1600, ...Top/Bottom Cleaning Brush.62" Width and 3-1/8" max. thickness opening, thickness adjustment by handwheel via worm gear with dial indicator.Equipped with: -- Top & Bottom nylon brushes driven by 3 HP drive motor (only 1-brush with machine). -- Separate variable speed feed motor with magnetic controls driving 3" dia. rubberized infeed & outfeed pinch rolls. -- Full fabricated sheet metal enclosure for efficient dust collection, dust enclosure hood with central 6" dia. dust outlet connection.

FLETCHER EZ-DOOR Raised Panel Door MachineThis freestanding machine can produce an entire 5-piece door in a matter of minutes. Easy to operate, the E-Z Door has a 4-position configuration to produce raised panels, cope/stile profiles and mullions for glass doors. Cathedral doors are produced by using a quick change template system.Specifications: -- Select cutter and material stop with the press of one button. -- Simple four position one spindle design. -- PLC controlled pneumatics. -- Rigid lubricated spindle assembly. -- Re-circulating ball bearing slides. -- 10 HP 230 or 460V/60HZ spindle motor – (460V/3PH=17FLA) – (230V/3PH=33FLA) -- 6,500 RPM spindle speed. -- 62 inch travel length standard with circulating ball bearing slides, cut rails to 59"; and panels to 55"; -- Includes: (4) Standard cutters (shape to be decided), others optional. -- Includes: one template of customers choice. -- 1-¼"; Arbor. -- CFM requirement is 392.Made in North Carolina, USA!

FRAMA - TC-1500: Hydraulic Copy Lathe with (1) V-Gouge Copy Head & (2) Manual Top Turret Heads & Knife SharpenerHydraulic Copy Lathe with: (3) Different speeds during execution of the work.Possibility of manual or automatic configuration on (3) intensities: (1) Regular working speed; (2) Slow working speed for difficult points reproduction; (3) Fast speed to eliminate nonproductive points. Technical Data -- Main drive motor: 6 HP. -- Hydraulic pumping unit: 2 HP Motor. -- Max. turning dia.: 300 mm (12"). -- Distance between center: 1,500 mm (59"). -- Max. cross-slide speed: 9.5 MPM (30 FPM). -- Carriage return speed: 11 MPM (36 FPM). -- Copying device stroke 75 mm (3"). -- Max. hydraulic pressure between cones: 20 kG/CBM. -- Headstock taper: MT 4. -- (8) Turning speeds: 1,000 - 1,250 - 1,750 - 2,000 - 2,250 - 2,500 - 3,500 - 4,500 RPM. Also included: -- FRAMA - ATC 2005: Knife Grinder. 2 HP Motor. -- (1) Steady rest - 70 mm; (1) 18 mm; (1) adjustable for square. -- Tailstock & Tool Holder.

FRAVOL VSR TOP & BOTTOM TRIMMERSpecifications: -- Edgebanding thickness 0.4 mm to 3 mm, 16 mm (0.62") to 60 mm (2.36") panel thickness capacity. The rough trimming function uses vertical copy pads and one disc copier between the two cutters in a horizontal position, allowing 0.4 mm to 3mm radius edge rough trimming without replacing the cutters. Panel working height (thickness) is from 16 mm to 60 mm.Equipped with & Features: -- Two 12,000 RPM motors complete with braze welded hard metal cutters Ø 50x16- Z6. Your choice of profiles R1; R2; R3; 5°; 30°. -- The machine comes with a new, patented worktable that provides smooth panel sliding and extremely flexible edging without using jigs. -- Sliding on nylon blocks allows perfect cleaning of the panel melamine surfaces.

FRAVOL SMART S600-23 EDGEBANDER (W/PRE-MILLING & CORNER ROUNDING): -- Specifications: Edge & Workpiece Capacity: 0.4 - 8 mm (0.016 - 0.315") edge; 10 - 60 mm (0.394 - 2.362") panel thickness; -- 140 mm (5.512") min. panel length and 100 mm (3.937") min. panel width. -- Feed-speed, 14 or 18 MPM (46 or 59 FPM.)Front-End Equipped With: -- Pre-Milling Station (RT/S), (2) motors @ 1.1 KW (1.5 HP), 12.000 RPM, LH & RH rotation w/pneumatic programmable jump control for chip-free and clean panel edges. Standard equipped with Dia. 60 mm x 64 mm H, with diamond inserts. -- IR Panel Heat Lamp: Improves gluing bond especially during cooler ambient temperatures and humid conditions. -- Automatic Edge magazine: For strips up to 8 mm & coil stock up to 3 mm thick PVC. -- Duo Gluing System: For regular granulate Hot Melt (EVA) and easy conversion to PUR glue. "Teflon lined" glue tank with bi-directional glue roller. Automatic temperature reduction during stand-by time. Glue tank has quick release system for maintenance or quick change to a different color or glue type. -- Side Pressure Section: (3) Pressure rollers, (1) motorized, (2) idle, pneumatic pressure control and programmable NC-positioning servo motor.Work-stations: -- End Trimming (INT 2/S): (2) motor @ 0.50 KW (0.70 HP) 12,000 RPM, automatic pneumatic chamfer 0° - 15° or total exclusion from control panel. Glides 45° on prismatic linear hardened steel guides. -- Trimming Unit (RF-S/S): Top/Bottom flush/bevel/radius milling unit, (2) motors, 0.73 KW (1.00 HP) 12,000 RPM. Pneumatic remote tilt in (2) positions, postion-1 for radius and thin edges up to 0.8 mm trimming, position-2 for flush trimming up to 8 mm edges.Equipped with banding thickness gauge block feature for quick and easy set-up/changeover. Includes 1-axis NC servo control motors for programmable change-over from thin to 8 mm solid wood edges or incremental re-positioning of the cutter head. -- Corner Rounding Unit (SYNCRO 1): Compact and easy to set up for leading & trailing edges, (1) motor 0.22 KW (0.295 HP) 12.000 RPM, electronically synchronized. Working capacity, min. 10 mm, max. 60 mm panel thickness. -- Profile Scraping Unit (RB/S): Top & bottom radius scraping for PVC - ABS edges. Heavy construction to eliminate vibrations and guarantee superior edge quality. Air blow-off jets and chip collection box. -- Clean Spray System: Top/Bottom spray nozzles applies edge cleaning solvent prior to buffing. -- Glue Scraping Unit (RC/S): Top & bottom pneumatically operated glue scraping on flat panel surface to remove potential glue squeeze-out that otherwise would coat the cloth buffing discs. -- Buffing Station (GSI/S): Top/bottom (2) motors, 0.09 KW (0.125 HP) 2,800 RPM, manual, horizontal, vertical and tilting adjustment -- Hot Air Unit PHON (GP/S): Top/bottom hot air blowers to restore PVC color after scraping. Electrical power 2,000 Watt, 0° to 600° C temperature adjustment.Complete With:• PLC Program Control, with 10.7" co

FRIULAIR ACT125UP MB 125 SCFM Non-Cycling Refrigerated Compressed Air DryerSpecifications: -- Max. inlet air pressure 203 PSIG. -- Max. inlet air temperature 158° F (70° C). -- Ambient temperature 34° - 122° F (1° - 50° C). -- Nominal pressure dew point 38° F (3° C). -- Refrigerant type R-407C.Equipped with: -- 890 W (1.19 HP) Refrigeration compressor motor. -- 95 W (0.13 HP) Fan motor. -- "ALU-DRY" heat exchanger. -- Graphic display. -- "DMC 34" LED Controller, with Condenser fan control, Scheduled maintenance reminder, Condensate drain valve timer, & Dryer malfunction detector.

FRIULMAC Quadramat Single End TenonerSingle end tenoner with (4) heads with Jump cope, cope, disc sanding and disc sandingSpecifications: -- Workpiece Length: 125 - 1500mm -- Workpiece Width: 125-1500mm -- Workpiece Thickness: 13 - 40mm -- Configuration: Jump-Cope, Cope, Wheel-Sanding, Wheel-Sanding -- First Station: 7.4 HP Jump-Cope/Profiling Unit with 40mm Diameter Shaft, 6000 RPM Rotation -- Second Station: 7.4 HP Cope/Profiling with 40mm Diameter Shaft, 6000 RPM Rotation -- Thirds Station: 4.7 HP Sanding Wheel -- Fourth Station: 4.7 HP Sanding Wheel -- Variable Speed Control of Sanding Stations from 750 - 1400 RPM -- Feed Speed: 13 - 98 FPM

FRIULMAC - Dual-Feed, ...Double End Cut-Off SawFor squaring workpieces and for transportation to a Planer or Moulder with a straightening table.Specifications: -- 79" Max. (2,000 mm) opening from Saw to Saw. Motorized opening with LED readout on the control panel; left-hand fixed with left-hand fence line. -- Hopper Magazine - material capacity: Min. length: 7.87" (200 mm), max.: 79" (2,000 mm); width: 1-1/8" (30 mm) to 6-3/4" (170 mm); and thickness: 0.59" (15 mm) min. up to 2-3/8" (60 mm) max.; hopper stack height: 23-1/2" (600 mm).Each side is equipped with: -- (2) Trim saw motors, 5.36 HP each; saw blade dia. 9.84" (250 mm). -- Hydraulic feed drive unit: 4 HP (3 kW) motor. -- Trimming & throughput capacity: Up to (55) pieces/Min.NOTE: Voltage transformer for 600 Volts available with the machine

FRIULMAC - Dual Feed: Double End Cutoff SawFor squaring the workpieces and for transportation to a Planer or Moulder with a straightening table. -- 59" Max. (1,500 mm) opening from Saw to Saw; motorized opening with LED readout on the control panel; left hand fixed with left hand fence line. -- Hopper Magazine, material capacity: Min. length 7.87" (200 mm); max. 59" (1,500 mm); width 1-1/8" (30 mm) to 4-3/8" (110 mm); thickness 0.59" (15 mm) min.; up to 2-3/8" (60 mm) max.; hopper stack height: 23-1/2" (600 mm).Each side equipped with: -- (2) Trim saw motors: 5.36 HP Each; saw blade dia. 9.84" (250 mm). -- Hydraulic feed drive unit with: 3 HP (2.2 kW) Motor. -- Trimming & throughput capacity: Up to (40) pieces per minute..

FRUILMAC - RANDOMAT E: End MatcherFor end matching: Flooring, cabinet & entry door rails, or tongue & groove. The feed through system allows: Continuous feeding of random length parts with any kind of profile. -- Capacity & Description -- Width cap.: 1-3/16" x 9-7/8'; Length cap.: 6-5/16" x 137" (longer lengths with additional support); 3/8" min. - 1-3/16" max. thickness cap. -- Approx. (10) cycles/Min - depending on part length & width. -- Feed System with: (2) 120" Long x 10" wide powered infeed & outfeed belt conveyors; parts are automatically fed & positioned with sensors. -- Positive stop to the 1st vertical shaper head (2nd shaper head next to the 1st one); cope cycle is automatic. -- Parts are conveyed past the 1st & 2nd shaper head; automatically reversed & positioned to a positive stop for the 2nd cut on the other end of the part. - At the same time, the 1st shaper head would be coping the 1st end of another part.Equipped with: -- Twin 7-1/2 HP - 7,500 RPM high-speed shaper motors, which pneumatically traverse in tandem for each cutting cycle. -- Cutting station with: Overhead holddown wheels; 4-point pneumatic clamping with: (2) Overhead & (2) horizontal clamps. -- Controller & Operator Interface Keypad: SIEMENS Controller; PLC controlled conveyor & shaper cut cycle for automatic operation; variable feed speed conveyor line; shaper head advance with LED readout on the controls. -- Includes: Infeed & Outfeed Conveyors.

FRIULMAC - MULIREX: End Matcher with: Stackable SpindlesEnd Matcher with: Stackable Spindle for fast Changeover!Equipped with: -- (2) Profiling Motors: 10 HP (7.5 kW). -- (2) Tool changer motors: 1/2 HP (0.25 kW). -- (2) Infeed/Outfeed conveyor belt motors: 1-1/2 HP (1.10 kW). -- Central conveyor belt: 3/4 HP (0.55 kW). -- Min. part length: 4-7/8" (120 mm). -- Min. part width: 1-3/16" (30 mm). -- Max. part width: 9-7/8" (250 mm). -- Min. part thickness: 1/2" (10 mm). -- Max. part thickness: 1-3/16" (30 mm). -- Min. cutter diameter: 6-5/8" (170 mm). -- Max. cutter diameter: 7-7/8" (200 mm). -- Diameter spindles: 50 mm. -- Spindle length: 11-1/4" (285 mm) under the nut for stackable tooling. -- Cutter speed: 9,000 RPM. -- Dust ports: (4) 4-3/4" for each spindle (2 on the top & 2 on the rear side).

FRUILMAC RANDOMAT E - End Matcher; -- For End Matching flooring or cabinet & entry door rails or tongue and groove. The feed-thru system allows continuous feeding of random length parts with any kind of profile.÷Capacity & Description: -- Width cap. 1-3/16" x 9-7/8'; length cap. 6-5/16" x 137" length (longer lengths with additional support); 3/8" min. - 1-3/16" max. thickness cap. -- Approx. (10) cycles/Min depending on part length & width; -- Feed system with (2) 120" long x 10" wide powered infeed & outfeed belt conveyors, parts are automatically fed & positioned with sensors. -- Positive stop to the 1st vertical shaper head (a 2nd shaper head is next to the 1st one); cope cycle is automatic. -- Parts are conveyed past the 1st & 2nd shaper head, automatically reversed and positioned to a positive stop for the 2nd cut on the other end of the part. At the same time the 1st shaper head would be coping the 1st end of another part.Equipped with: -- Twin 7.5 HP - 7,500 RPM high-speed shaper motors which pneumatically traverse in tandem for each cutting cycle. -- Cutting station with overhead hold-down wheels and 4-point pneumatic clamping with (2) overhead & (2) horizontal clamps. -- Controller & Operator Interface: Key Pad SIEMENS Controller, PLC controlled conveyor & shaper cut cycle for automatic operation, variable feed speed conveyor line, and shaper head advance with LED readout on the controls. -- Includes Infeed and Outfeed Conveyors

Sanding wheel shaper for the production of profiles on the sanding wheels. -- Template carrier holds metal or plexiglass template (same as can be used on the moulder knives). -- Spindle length 5" with 1" diameter arbor for wheel support. Handles 8" diameter wheels (3) included with the machine. -- X and Y axis on dovetail slide with lineal bearing support for smooth movement during the wheel grinding. Pneumatic clamping on grinding wheels. Depth of grinding 1.5" for raised panel. -- Tilt capabilities from 0 to + 30°. -- Grinds all types of varda wheels on 1 HP motor with speed of 1,750 RPM. --You can customize this machine to you needs.

Fukami RT-300 Straight Line Rip SawSpecifications : -- 12" Blade cap., -- 10 HP main motor, 5,700 RPM arbor speed, -- 2-3/8" depth of cut, 8-1/4" min. stock length, 15" throat depth; -- 7-1/2" wide rubber pad feed chain, -- Variable feed speed 50 - 100 FPM, -- 31" X 55" table size.Equipped with and Features --: Anti-Kick back fingers, -- Push button and chain lubricator.NOTE from the seller : Fukami Straight Line Ripsaw. In good condition. Good non marring track is like new. Used in small shop. Nice compact machine with dust collection hood. 12"; carbide blade. 10 hp 3 phase belt drive. Easily changed to single phase. Owner can load