6" Wide x 108" long belt (non-oscillating), 6" x 40" graphite covered platen, 1.5 HP motor w/magnetic switch, 6" dia. drive pulley, 7-3/4" x 37" front table & end table for radius work both w/approx. 6" vertical adjustment. -- Features: Industrial laminated tables, fabricated steel base, swing-away type safety dust hood, rigid tracking.

EXTREMA ESO-108.1 Oscillating Edge Sander with End Sanding Kit. -- 6" Wide x 108" long belt, with 1/4" oscillation travel -- 6" x 40" Graphite covered platen. -- 1-1/2 HP Single-Phase motor w/magnetic switch. -- 7" Diameter drive pulley, and 3" Idler pulley. -- 8" x 37" Front table with 5-3/4" vertical adjustment. -- Adjustable 12" x 19" End table for radius work with a 5-3/4" vertical adjustment. -- Heavy laminated tables, fabricated steel base and dust hood with 4" dust collection port. -- CFM Requirements: 400. -- Weight: 425 Lbs.

EXTREMA ESO-108.3 Oscillating Edge Sander with End Sanding Kit. -- 6" Wide x 108" long belt, with 1/4" oscillation travel. -- 6" x 40" Graphite covered platen. -- 2 HP Three-Phase motor w/magnetic switch. -- 7" Diameter drive pulley, and 3" Idler pulley. -- 8" x 37" Front table with 5-3/4" vertical adjustment. -- Adjustable 12" x 19" End table for radius work with a 5-3/4" vertical adjustment. -- Heavy laminated tables, fabricated steel base and dust hood with 4" dust collection port.

EXTREMA EXCESS XS-1E37 SINGLE HEAD WIDE BELT SANDER37" Width capacity, 0" to 6" conveyor bed opening. Mono-block construction for solid, vibration free operation and increased durability. -- Equipped with: Combination sanding head with rubber covered contact roll & graphite covered platen. -- Over thickness material feeding safety device. -- Digital material thickness controller setting with LED readout accurate to a thousandths of an inch. -- "Automatic Thickness Setting" device for easy setup. -- OMRON Electronic abrasive belt tracking. -- GOODYEAR Endless conveyor belt with automatic belt tracking. -- 20 HP Main motor. -- REGAL Variable feed speed drive unit; 2 HP motor. -- 1/2 HP Power elevation motor. -- Large cabinet style doors for easy service access. -- Pneumatic abrasive belt tensioning. -- Double infeed & outfeed covered holddown rollers. -- Infeed conveyor extension with safety stop bar, emergency stop button and motor load meter. -- Operations manual & free box of 3M Sanding Belts. -- Optional 460 Volt / 3 Phase.

EXTREMA XS-1E43 Single Head Wide Belt Sander42" Working width, up to 5" max. opening with electronic digital microprocessor thickness control.Equipped with: -- Rubber-covered contact drum and 2-1/2" wide finishing platen, 25 HP main motor; -- 43" x 60" Abrasive belt, TRU-TRAK solid-state electronic belt sensing with pneumatic tracking. -- GOODYEAR Endless conveyor belt with pneumatic tracking, 2 HP variable speed feed motor from 15 - 48 FPM. -- 0.5 HP Motor to raise & lower table via (4) jack screws, an over-thickness bar at the infeed of machine, and AUTO-SET thickness device. Complete with & Features: -- Double infeed & outfeed rubber covered holddown rolls. -- Air operated disc brakes on main motor, front & rear emergency stop buttons, and motor load meter. -- SQUARE D Electrical controls; magnetic Starter with overload protection, and electrical interlock at sanding belt access doors.NOTE: Also available wired for ...460V operation.

EXTREMA PERFORMA XS-2P52 Wide Belt Sander (2) Heads;52" Width cap. Drum, Roller and Platen - 75"; Belt Lengths Head Configuration: -- 1st Head: Contact drum 30 HP motor; -- 2nd Head: Roller and Platen 30 HP motor.Features: -- Over thickness safety device -- Infeed bed rollers -- Digital thickness controller -- Individual amp meters -- Disc brakes on sanding heads -- Telemecanique electrics. -- Camozzi pneumatics -- Variable speed drive system.Specification: -- Feed motor 3 HP -- Elevation motor 0.5 HP -- Max. thickness 6" - Min. thickness 1/8" -- Contact drum 1st head 8" dia. -- Roller drum on 2nd head 5" dia. -- Dust Collection requirements 4800 CFM -- Feed speeds 15 - 50 FPM. -- Weight 6500 Lbs -- AMPS (220 V / 460 V ) 148/74.

EXTREMA 126TV Single Sided Planer;26" Max. width capacity, 11.75" thickness, Solid cast iron construction. -- Precision ground cast iron table with motorized programmable height adjustment; 1/2 HP elevation motor. -- 20 HP Main drive motor -- Scale & pointer readout for accurate thickness adjustments. -- "VECTOR" cutterhead with (6) rows of 4-sided inserts. -- 1 HP Feed drive, variable feed speed setting from 20 to 75 FPM. -- Sectional steel infeed roller & segmented chipbreaker. -- Independently adjustable feed rollers; (2) Externally adjustable bed rollers. -- Hinged top for easy access to cutterhead & gear assembly. -- Self-braking motor with magnetic starter & thermal overload switch and Emergency stop. -- Includes Operations manual, parts list & tool kit.

EXTREMA XP-124TV Single Head PlanerSpecifications: -- Solid cast iron construction. -- 15 HP Main drive motor, 1 HP feed motor 20 to 70 FPM, 1/2 HP elevation motor. -- Precision ground cast iron table w/motorized programmable adjustment. -- Scale & pointer readout for accurate thickness adjustments. -- "VECTOR" insert cutterhead with (4) sided inserts. -- Fixed feed speed setting for consistent stock removal. -- Sectional steel infeed roller & segmented chipbreaker. -- Independently adjustable feed rollers. -- (2) Externally adjustable bed rollers.Features: -- Hinged top for easy access to cutterhead & gear assembly. -- Self-braking motor. -- Magnetic starter & thermal overload switch. -- Emergency stop. -- Operations manual, parts list & tool kit. -- Options: Single-phase power, please add ...$ 100, 460 volt add...$ 150.

EXTREMA XP-610 SINGLE SIDED PLANER24" Width capacity, 8-3/4" thickness, solid cast iron construction. -- 10 HP main drive motor -- Precision ground cast iron table w/motorized height adjustment, with digital thickness display; 1/2 HP elevation motor. -- Scale & pointer readout for accurate thickness adjustments. -- "VECTOR" cutterhead with (6) rows of 4-sided inserts. -- Variable feed speed from 20 to 42 FPM; 1 HP feed drive. -- Sectional steel infeed roller & segmented chipbreaker. -- Independently adjustable feed rollers. -- (2) Externally adjustable bed rollers. -- Hinged top for easy access to cutterhead & gear assembly. -- Self-braking motor with magnetic starter & thermal overload switch. -- Emergency stop. -- Operations manual, parts list & tool kit.

EXTREMA XP-615AZ Single Sided Head PlanerSpecifications: -- Width: 24" -- Main HP: 15 HP -- Feed HP: 1 HP -- Elevation HP: 0.5 HP -- Max. Thickness: 8.75" -- Min. Thickness: 0.375" -- Max. Cut: 0.25" -- Min. Length: 10.5" -- Cutterhead Speed: 6000 RPM -- Feed Speed: 20-42 ft/min -- Air Requirements: 1000 CFM -- Thickness Adjustment: PLC ControllerBed Roller Adjustment: External -- Powered Bed Rollers: Top and Bottom -- lnfeed Roller: Standard -- Amps (230V / 460V): 41A/20A -- Weight: 2345 LbsFeatures: -- Solid cast-iron construction -- Sectional infeed rollers -- Huge 8-3/4"thickness capacity -- 6000 RPM cutterheads -- Anti-kickback fingers -- Segmented chip breakers -- Sectional feed rollers -- XP-615 Digital Controller -- Motorized table elevation -- Available with straight, STEALTH, or ilECTDFi cutterheads -- Heavy duty screwjack elevation system -- Easy access internal workings -- External bed roller adjustmentsOptional: -- In-feed Roller

EZ CAR CRUSHER MODEL A+ --Opening 20 ft long x 7'6" width x 8 ft height --System Pressure 2500 psi --Port Reliefs Set At 2650 psi --Cylinders 10" bore --Travel 78" --Shaft 4" rod --Remote --Approx 5,500 Hours

MODEL A EZ CAR CRUSHERHydraulicsSystem Pressure 2500 psiPort Reliefs Set At 2650 psiCylinders 10" boreTravel 78"Shaft 4" rodOpeningSize 20" x 8'1" x 7'7"OverallWeight 61,000 lbsLength 43'3"Travel & Operating Height 13'3"

EZ SANDER EZ-3760 Wide Belt SanderEZ-Sander's are built to with the ability to hold very tight tolerance (+/-.003) side to side when set up properly.Specifications: -- The sanding head is a combination head that consists of a 5" rubber-covered contact drum for the more aggressive sanding and then followed by an adjustable 2-1/2" graphite-covered felt polishing platen for doing very fine finishing sanding using a 37" X 60" abrasive belt. -- The conveyor belt speed is set to run at 10 - 30 FPM and is controlled via AC variable speed unit mounted in the main control panel. Simply adjust the dial setting to your desired feed speed. -- Double infeed and outfeed hold-down rolls are provided to help ensure proper part feeding through the Sander. -- The conveyor table/bed opening has a 0" to 5" opening allowing the operator to sand some parts as thick as 5" and the ability to sand very thin parts as well. -- Power raising and lowering of the conveyor bed is standard. -- Digital thickness display is standard.Complete with & Features: -- EZ Sander is equipped with a state-of-the-art electronic tracking system for the abrasive belt. -- Emergency stop heavy-duty caliper disc brakes bring the sanding head to a stop within 4 to 5 Sec when activated by the machine's safety interlock system. -- Limit Switches on both sides of the abrasive belt to keep the belt from over-travel. NOTE: -- Available in single phase with a 7.5 HP or 10 HP 3-Phase main drive motor. -- Voltage change to 440 Volt ...$275.

FELDER G-330 EDGEBANDER0.4 - 3 mm Edge thickness cap. and 40 mm panel thickness; 3" min. width and 4-3/4" min. panel length.Equipped with: -- Quick Melt Teflon coated glue pot for granular hot-melt adhesive. -- Heavy Duty guillotine for up to 3 mm thick PVC. -- Integrated Operator PLC controls and an LCD display. -- "Anti-slip" rubberized surface chain pads.Workstations: -- Single motor, Double Blade End Trim with HF motor - 12,000 RPM. -- Top & Bottom Flush/Bevel Trim, bevels 0° - 15° (0.5 HP motor - 12,000 RPM each). -- Open space at out feed . -- Single feed speed of 26 FPM.Complete with: -- Sound & Safety enclosure over trim stations and outrigger panel support, and used tooling.NOTE: Seller states that the equipment has less than 500 hours of use!

FELDER FORMAT 4 - C-EXPRESS 920 CNC MACHINING CENTER (FEED THRU W/ROUTING): -- Specifications: Automatic CNC Feed Through Point to Point Boring Machine that combines flexibility and high productivity.A perfectly suited solution for small to midsize companies & artisans in need of an automatic solution for precision drilling with a low cost investment.Parts can be discharged at the opposite end of the machine for automated material handling or returned to the Operator for manual unloading. -- Working Field:Max. panel size on X-Axis 118" (3,000 mm); Y-axis is 36.2" (920 mm); Z-axis is 2" (50 mm).Min. panel on size X-axis is 11" (280 mm); Y-axis is 7.1" (180 mm); Z-axis is 0.4" (10 mm).Max. Panel weight 66 Lbs (30 kG). -- Positioning Speed: Panel feeding speed of 229 FPM (70 MPM), Y-axis at 229 FPM (70 MPM), Z-axis at 65 FPM (20 MPM).Axes positioning by AC drives & brushless Servo motors; the Panel moves in X-axis & the boring head moves in Y- & Z-axes. -- Work Area:NC Controlled "Optical Laser Sensor" creates a zero-panel reference point by reading the panel's ends; this ensures that RH & LH (mirror image) panels will always be symmetrical.High precision clamping automatically positions the workpiece. Automatic presser moves independently and adjusts to workpiece thickness. Pneumatic side pusher makes locating workpiece accurate and efficient. LH Side pressure clamp with automatic adjustment & pneumatic locking according to the panel width.Scratch resistant rollerball table makes for ease of loading parts into the machine. -- Boring Unit:3 HP (2.2 kW) Motor, variable speed from 4,500 - 8,000 RPM.(9) Independent vertical spindles on 32 mm centers: (5) Spindles in X-axis & (4) spindles in Y-axis.(6) Horizontal spindles with: (2 + 2) in X-Axis & (1 + 1) in Y-axis.(1) X-Axis grooving saw for max. 120 mm dia. blade, variable speed from 5,500 - 10,000 RPM. -- Machining:5 HP (3.7 kW) Motor, variable speed from 1,000 - 18,000 RPM with ER 32 adaptor & manual tool change system. -- Operator & Machine Control: PC-Based user-friendly icon driven Control housed on the main machine base + "WOODFLASH" Operating System. 19' LCD Displays programming graphics, functions, machine data. -- Complete with: User & Maintenance Manuals; handheld pendant. -- Options Include: &#9679 Special side clamping device for min. panel size in Y-axis of 2-3/4" (70 mm). &#9679 Additional retractable infeed support table with roller balls. -- Actual model is: FELDER FORMAT 4 - C-EXPRESS 920 CLASSIC

Large table size, extendable in all three directions by up to 39" (1,000 mm) without the requirement of tools. Comfortable one-handed lever operationHeavy-duty eccentric clamp, usable on the left and right-hand side.Specifications: -- 3 HP motor, tilting head, manual hand lever control for mortise length and depth; 13" x 22" table with eccentric clamp -- 3000 RPM, reversible motor that caters for left and right cutting bits and a solid quad-jaw chuck with clamping range from 0–20 mm -- Lateral range of motion is 250 mm, cut depth is 160 mm, available height adjustment is 130 mm and there are solid locking stops in all three directions for setting precise stops.Features: 2-Jaw chuck with 5/8" capacity, Dust control collection tray below the cutter out to an 80 mm outlet,Complete with (2) adjustable and removable extension wings; fence for 90° & 45° mortises, extended stop bar on each side of table.

This FISHER + RUCKLE is actually called a "FISHER + RUCKLE/MONGUZZI ADF76-2800" Double-Knife Veneer Guillotine.110" (2,800 mm) Max. knife length, double-knife guillotine; motorized front knife adjustment.Specifications: -- 3/8" - 20-3/8" (9.5 - 517 mm) Adjustment; 3-15/16" (100 mm) max. daylight opening. -- Microprocessor controlled knife opening with: Keypad entry & LCD readout. --Rear fence with auto-trim cut feature, slow & fast fence movement. -- Hydraulic pressure beam & knives can be activated separately & together. -- Hydraulic system with: 10 HP (7.5 kW) Pump and reservoir for knives & pressure beam activation. Complete with: -- Installed knives and Light beam Infrared safety zone.Actual model ix AFD 76-2800 &#9679 . OEM, Monguzzi model is TRM-2L. Exactly the same machine.

FLETCHER EZ-DOOR Raised Panel Door MachineThis freestanding machine can produce an entire 5-piece door in a matter of minutes. Easy to operate, the E-Z Door has a 4-position configuration to produce raised panels, cope/stile profiles and mullions for glass doors. Cathedral doors are produced by using a quick change template system.Specifications: -- Select cutter and material stop with the press of one button. -- Simple four position one spindle design. -- PLC controlled pneumatics. -- Rigid lubricated spindle assembly. -- Re-circulating ball bearing slides. -- 10 HP 230 or 460V/60HZ spindle motor – (460V/3PH=17FLA) – (230V/3PH=33FLA) -- 6,500 RPM spindle speed. -- 62 inch travel length standard with circulating ball bearing slides, cut rails to 59"; and panels to 55"; -- Includes: (4) Standard cutters (shape to be decided), others optional. -- Includes: one template of customers choice. -- 1-¼"; Arbor. -- CFM requirement is 392.Made in North Carolina, USA!

FLETCHER FM-2000 Contour EdgebanderSpecifications: 0.4 mm to 2 mm Banding thickness, up to 2" panel thickness, Unit to run strip veneer, coil, rolls of PVC, melamine, or wood veneer. Large overhead glue pot with a quick heat time of 10 minutes. Equipped with: -- Programmable temperature control with safety interlock so that applicator does not run until proper operating temperature is reached. -- 1-3/4" silicone-coated drive roll. -- Foot pedal-controlled tape advance. -- Foot pedal emergency stop. Optional Equipment: -- Power-Feed $ 2,618.00 -- 3° Manual Tilting Table $ 809.00 -- 45° Tilting Table $ 5,382.00 -- Push Button Powered Operated Tilt Table $ 6,232.00 -- Outboard Stock Support $ 1,565.00 -- 3MM Capable $ 2,950.00 -- 4"; Thickness Capacity $ 10,000.00

FLETCHER/DELMAC - DMG-50CB, ...Contour EdgebanderSpecifications -- Overall table size: 18" x 48"; x 39-1/4"; H; 18" x 48"; Tilting section with: 0° - 15° Tilt.Equipped with: -- 20" Dia. Coil table. -- Guillotine. -- Glue Pot & Roller. -- DELMAC Thermo-Regulator Control with: (2) WATLOW "Series 965" Digital temperature controllers; LED display & touchpad for Glue pot & roller; LCD band length counter. -- Dual foot pedal controls.