NEDERMAN - S-1000: BAG FILTER Dust CollectorThe NEDERMAN S-Series Baghouse Dust Collector is: Quick to install and easy to operate. It is the ideal solution for the small shop or single work-cell operation. -- Includes: 10 HP Motor; CFM range from 4,000 CFM @ 8" WG to 5,000 CFM @ 7" WG. -- Equipped with: 10 HP - 1,750 RPM TEFC Motor; (24) Beane material filter bags; 230 Gallon Dump Bin: magnetic starter. -- Features: 360 Sq./ft. of filter medial; easy installation, typically (1) hour; quiet operation. -- Inlet opening 15". (2) Units available!

NEDERMAN S-750 Bag House Dust Collector7.5 HP - 1,750 RPM TEFC Motor. -- (24) BEANE material filter bags; (3) plastic waste collection bags; (3) clamps for easy removal of waste bags. -- Features: 243 Sq/ft. of filter media; easy installation typically (1) hour; quiet operation; (3) waste discharge points; 280 mm inlet. -- Unit is very versatile and capable of a nice range of operation; 2,500 CFM @ 10"Wg; 3,500 CFM @ 8"Wg; 4,500 @ 6"Wg. -- Magnetic starter included for 230 V - 3 Ph. -- 230 Gallon Dump Bin

NEDERMAN - NFSZ 3000/1N. Modular Filter, fully-featured with: NRSZ-10 - Rotary Air Lock waste discharge; Spark Detection; Variable Speed motor drive7,320 CFM; Approx. 8-to-1 air-to-cloth ratio; positive pressure; expandable Heavy-Duty Baghouse Dust Collector System. - Designed for small to medium-sized air flows with: Large material concentration (dust loading).Specifications -- Total 915 sq./ft. filter area; (25) SUPERBAG 2000 XT15 filter bags. -- Includes: (1) Filter module sections (expandable) with: Combined explosion & access door in each section; each with 1.5 HP regenerative fans for cleaning of filter media. -- Unit is ATEX rated; Hopper for collected material to Rotary Air Lock at one end and discharging into a waste bin (not included). -- Equipped with: (1) Ground-mounted 40 HP TEFC Belt driven motor with Variable Frequency Drive and NEDERMAN MH type Blower package; about 18" inlet.Capable of approx.: 7,500 CFM w/drive guards; motor & fan are a common steel base/frame with current roof-mounted installation. - Main pipe to fan inlet is approx. 18", as is the fan outlet pipe. -- Features & Includes: Spark Detection system controlling an Abort Gate on return line and mounted on separate steel support; 22" dia. back pressure (flow) flap valve located between fan discharge & baghouse inlet. -- Complete with: Access ladder/platform; drain with plug: quick open access doors; inlet flange; electrical disconnect; separate control panel with motor starter for main blowers. -- Includes: Primary outside pipe; approx. 10' high support steel structure; platform & ladder mounted on top of structure.Baghouse dimensions: 48" x 94-1/2" Square (1,200 x 2,400 mm) for both modules; height of Baghouse shell will be provided.Actual model: NFSZ 3000 - 1N

NEWCNC - Smart ER Series I 510: CNC Router w/ATC & Lathe5' x 10' FLAT TABLE CNC ROUTER W/ATC & LATHE: Great for "Nested Base Manufacturing" or just about any type of 3-Axis work. -- Working Table: 63" (1,600 mm) x 122" (3,100 mm). - (4) Pop-Up stops to aid in panel positioning; an "M-code" controlled 4-zone electrovalve; special high flow Vacuum Table System. -- X- & Y-Axes Speed: 3,181 IPM (265 FPM / 83 MPM) & Z-Axis: 350 IPM (29 FPM / 12 MPM) for quick traverse positioning that reduces total CNC machining time between cutting cycles. - "YASKAWA" Servo drives power the axes movement. -- Industrial machine tool welded structurally engineered: Machine base provides a solid foundation for superior cut quality; entire frame is stress relieved & heat treated. -- Moving gantry bridge. Travels on: "THK" Large thick hardened & precision ground rectangle linear guide slider-ways giving extra smooth movement for high-speed traverse & accurate cutting. -- Tool Gantry & Bridge Movement: Large thick inclined rack & pinion teeth; vertical axis travels on a large diameter precision ball screw for smooth consistent movement. -- Machining: (1) 12.6 HP (9.4 kW) Air-cooled SCM Router spindle with: "HSK 63F" Adaptor; variable programming speeds: From 1,000 to 22,000 RPM. -- Tools are loaded into the "SCM" spindle by: (1) 8-position plate "on the fly" ride along carousel ATC (automatic tool changer). -- Tool heights can be set using the Tool Length setting gauge (included); machine requires ER-32 tool collets. -- CNC Control: Industrial Grade "OSAI 10/510" OPEN CNC control with: 19" Color monitor; includes self-diagnosis & alarm history display & background editing; up to (4) simultaneously controlled axes with: 3D simulation; helical interpolation; tool offset; length compensation & backlash compensation. -- Compatible with virtually all CAD/CAM programming software on the market; you choose the software that best suits your needs. -- Includes: (1) 7-1/2 HP (5 kW) "Rotary Vane" type Vacuum Pump. -- Complete with: Dust hood with 6" manifold connection; Tool Length setting gauge; "MPG" handheld wheel remote; safety bumper system on both sides of the moving bridge; safety bar around the back of the machine. -- Options Include: (1) 12' Lathe attachment with: Chuck & tailstock (...$ 8,450 value); (1) additional 7.5 HP (5 kW) Rotary Vane Vacuum Pump (...$ 5,150 value).

NEWCNC - Smart ER Series II 510: CNC Router w/ATC & Boring5' x 10' FLAT TABLE CNC ROUTER W/ATC & BORING: Great for "Nested Base Manufacturing" or just about any type of 3-Axis work. -- Working Table: 63" (1,600 mm) x 122" (3,100 mm). (4) pop-up stops aid in panel positioning & a "M-code" controlled 4-zone electro valve special high flow vacuum table system. -- X- & Y-Axis speeds are: 3,181 IPM (265 FPM / 83 MPM) and Z-axis is 350 IPM (29 FPM / 12 MPM) for quick traverse positioning that reduces total CNC machining time between cutting cycles. - "YASKAWA" Servo drives power the axes movement. -- Industrial machine tool welded structurally engineered machine base provides a solid foundation for superior cut quality; the entire frame is tress-relieved & heat treated. -- The moving gantry bridge travels on: "THK" Large thick hardened & precision ground rectangle linear guide slider-ways giving extra smooth movement for high-speed traverse & accurate cutting. -- Tool gantry & bridge movement by: Rack & Pinion w/large, thick inclined teeth; the vertical axis travels on a large dia. precision ball screw for smooth consistent movement. -- Machining. (1) 12.6 HP (9.4 kW) Air-cooled SCM Router spindle with: HSK 63F adaptor, variable programming speeds from 1,000 to 22,000 RPM. -- Tools are loaded into the "SCM" spindle by: (1) 8-Position plate "on the fly" ride along carousel ATC (automatic tool changer). -- Tool heights can be set using the Tool Length setting gauge (included); machine requires ER-32 tool collets. -- CNC Control: Industrial grade "OSAI 10/510" OPEN CNC control with: 19" Color monitor; includes self-diagnosis & alarm history display & background editing; up to (4) simultaneously controlled axes with: 3D Simulation, helical interpolation, tool offset, length compensation, & backlash compensation. -- Compatible with virtually all CAD/CAM programming software on the market; you choose the software that best suits your needs. -- Includes: (1) 7-1/2 HP (5 kW) "Rotary Vane" type Vacuum Pump. -- Complete with: Dust hood with 6" manifold connection; Tool Length setting gauge; "MPG" handheld wheel remote; Safety Bumper System on both sides of the moving bridge, and safety bar around the back of the machine. -- Options Include: (1) 10-Spindle Vertical Boring Block with (5) independent spindles in "X" axis & 5 independent spindles in "Y" axis (...$ 8,450.00 value). (1) Additional 7-1/2 (5 kW) Rotary Vane Vacuum Pump (...$ 5,150 value).

This item is in an Auction on exfactoryauctions.com. Go here to view item: http://exf.ac/i6r NEWMAN S-248 24" x 8" Single-Sided Planer Specifications: Planing thickness 1/16” - 8”. Min. stock length 13”, 4” Butted. Infeed & Outfeed table sizes 24" W x 16-3/4” L. Feed speeds 20 - 100 FPM. Equipped with: 4” Dia. 4-straight knife cutterhead. Segmented serrated upper with 2” W Spring-loaded segments & (3) Solid steel lower feed rollers. Chip breaker, with 2” W Reversible spring-loaded segments.

Newman HP-688 Twin Bay Hydraulic Cold Press6-Sections (top platens) each 24" x 30" each, Center posts between third and fourth platens, creating two overall areas of 30" x 74". Specifications: -- Max. fixed opening 48" with 11" cylinder stroke, each platen section has (1) 10" bore with 5" dia. ram cylinder; -- Each platen is 15/16″ thick and it’s back structure is webbed every 5-1/2″ X 7-1/2″. -- Side-mounted self-contained hydraulic system w/tank, 10 HP continuous operating pressure compensating pump. -- Hand-Valves to Cycle Individual Platens with pressure gauges for each platen. -- Idle Pop-Up Bed Rollers in the bottom platen for easy loading and unloading.Over all the press is in excellent condition, is extremely heavily built, and is also a beautiful impressive press in person.

NEWMAN/Cameron - KF-24: Dip Chain Gang Rip Saw with CAMERON "34H-M1" Infeed SystemSpecifications -- Saw Arbor: 24" Arbor cap.; 14" max. dia. tooling; 4" max. motorized thickness adjustment;22" min. length for glue joint accuracy; 6" throat. -- 2-13/16" Dia. arbor; 24-1/2" capacity saw sleeve arranged for 3-1/8" dia. bore saw blades; saw blade options: 10" - 14" Dia.; spacers: 4-5/8" dia. includes: (1) Saw sleeve and spacers. -- 75 HP - 3,600 RPM TEFC Direct drive motor; arbor with: Disc brake & load meter; arbor lockout on the access door. Feed & Chain: -- 5 HP Variable feed speed: 20 to 100 FPM with: Jam arbor protection. Dip bed carried on: 5" Pitch hardened Double-V chain; hardened dip cams; extruded structural aluminum feed bed slats with: Replaceable steel-backed rubber insert strips; automatic chain oiler with low level shutoff. -- (2) 4" Dia. air loaded overhead pressure rolls; spring-loaded overhead bed plate; pressure rolls & bed plate unit with motorized adjustment; slide type infeed guide with: Handle block; either side of the guide can be used for a stock engraver. -- Anti-kickback finger system with: (1) Lower & (2) upper on infeed; (1) upper kickback on outfeed. Equipped with & Features: Upper outfeed main dust hood: 7-7/8" Dia. 2,150 CFM Infeed dust hood 4-7/8 dia. (855 CFM). (1) Spare sleeve; (2) setup fixtures; generous array of spacers (see photos).

NORDFAB NFK Series Modular Dust Collector with (8) Modules, reverse air cleaning and drag chain unloading into a Rotary Air Lock (RAL) --23,000 CFM approx. capacity based on filter area and desired Air to Clothe Ratio. With 50 HP. + 40 HP (was used as a transfer blower) Consisting of (248) filter bags of 8.7" dia. x 77.2 " long(220 mm x 1,960 mm long) also (8) filter bags of 8.7" dia. x 54.1" long.(220 mm x 1,375 mm long) - located at cleaning fans - for a total of 3,680 sq. ft. of filter area. -- Consists (8) modules and (1) inlet blank module. Fan inlet approx 26" dia. -- Bottom conveyor chain with scrapers carrying the dust to one end and fed into the RAL -- Includes NRS-10 Rotary Air Lock and Transfer Blower to convey the dust to an enclosed waste container (not included). -- Electrical control panel with starters included. -- Overall dimensions 32' long x 7.5' depth x 13.5' high (without support steel)., Approx weight 10,000 lbs. --Actual model is NFK 8AJ/1BL

NORFIELD - 250-M: Strike Router -- Strike Router capacity: 9' Length x 1-5/8" thickness cap.; infinite width; mortising plate & bolt relief in: (1) Continuous operation. -- 1-1/2 HP Router: Processes any strike up to 4-7/8" long, including T-strike. -- Rectangular relief leaves more wood in jamb for greater strength and more professional appearance.

NORTH AMERICAN PL-30 ROTARY PHASE CONVERTERPro-Line is the Professional Series, digital start, CNC rated, general purpose single phase to three phase rotary phase converter designed to take standard single phase energy and supply full running current to three-phase equipment.Equipped with: -- Control Panel -- NEMA 1 Enclosure (Indoor) -- Built-in Motor Starter -- Digitally Controlled and Protected Start Circuit -- ABB / Baldor Idler Generator Motor -- ODP (Open Drip Proof) – Indoor Rated -- Soft Start -- 10-Year Parts / Lifetime Labor Warranty

NORTHFIELD - #4, ...Table SawSpecifications: -- 16" Dia. saw blade cap.; 7.5 HP - 3,450 RPM motor; 1" dia. arbor; 13/16" dado cap. with: Thin collar; blade tilts: 0° - 45°; 32" rip cap. with T-type fence.

This item is in an Auction on exfactoryauctions.com. Go here to view item: http://exf.ac/i6q NORTHFIELD 12HD 12" Heavy-Duty Jointer Specifications: Max. depth of cut 5/8", Rabbeting cap. 5/8" x 12". 17” x 51-1/2” x 32-1/2” H. Outfeed table size 17” x 43” x 32-1/2” H. Equipped with: 3-1/2” Dia. 3-Knife Cutterhead. 5 HP - 1,735 RPM Motor. 52” L x 5-1/2” H Cast-iron fence, with 0° - 45° Tilt. Swing-away guard.

NORTHTECH NT-EV-920RC Dual Head Wide Belt Sander2-Head Wide Belt Sanding Machine with 37" capacity. Specifications: -- First head 8-1/4" Dia. grooved rubber contact roll, with 20 HP motor. -- Second head: Combination finishing platen with grooved rubber roller and polishing pad, with 15 HP motor. -- Two (2) infeed and outfeed spring loaded holddown rollers; 2 HP variable speed feed drive. -- Sanding belt size: 37" X 85" and with electronic belt tracking. -- Motorized opening between conveyor bed and sanding heads. -- Ammeters for measuring motor loads. -- Includes spare abrasive belts.

NORTHTECH NT-KL-43-RC Wide Belt Sander (2) Heads;43" width cap. Drum, Combination Head.Head Configuration:1st Head: Rubber-covered contact drum with 25 HP motor2nd Head: Combination head with a rubber-covered contact drum and 2-1/4" wide finishing platen, 20 HP motor.Specifications: -- Thickness opening with PLC control, (DP-525 controller) keypad entry automatically adjusts to any thickness with LED readout. -- 37" x 75" Abrasive belts, TRU-TRAK solid state abrasive belt tracking. -- Variable feed drive 13 - 49 FPM, 2 HP motor. -- Endless belt conveyor, infeed and outfeed rubber covered pinch rolls. -- Complete with: 0" - 6" Automatic part thickness set up.Equipped with & Features: -- Infeed and outfeed rubber covered spring loaded holddown rolls. -- Feed emergency stops at infeed. -- Disc brakes on sanding heads, electrical interlocks on main access doors, and motor load meters. -- Note: Year of manufacturing has to be verified.

NORTHTECH NT-6108ES-6 Edge SanderSpecifications: Sanding Belt is powered by a 3 HP 230/460V motor. -- The platen measures 6-3/4″ X 39″ and has NEW graphite. Rubber covered direct drive pulley. -- Equipped with: (1) 7-3/4" x 37" Adjustable side table and (1) 11-1/2" x 19" Adjustable end table; both side & end tables have vertical table travel w/hand wheel adjustment. Complete with: -- Magnetic controls with overload protection & dust hood with 4" dia. outlet.

NORTHTECH - NT-KL-920-PRK- B & NT-KL-920 PRK-U, ...Top & Bottom 3-Head Planer Sander3-Head bottom with: Planer, drum and platen; 3-head top with: Planer, drum, and platen 920 mm (36") wide.Capacity: 36" x 5" thickness.SpecificationsBottom Machine Model: "NT-KL-920 PPR". -- Infeed driven Conveyor: 37" x 72" Long. -- 1st Head: Spiral cutterhead; (8) rows of 15 x 15 x 2.5 mm inserts carbide knives; (4) sides for rotation; low tool cost.Cutterhead: 175 mm (7") Dia. and 50 HP motor. Segmented chip breaker before the cutterhead. -- 2nd Head: Contact roller; (280 mm) 11" in dia.; 70 durometers, powered by a 40 HP motor; running at 3,600 FPM belt speed.Sanding belt size: 85" x 37". -- 3rd Head: 3-1/4" Pneumatic Polishing Platen; engineered as a combination station, air-cushioned & adjustable in pressure to various grits and materials application. Powered by a 30 HP motor. -- Lifting & lowering conveyor bed; 1-1/2 HP motor (includes auto. thickness setup device). -- Variable speed: 7.5 HP; inverter duty motor integrated with an AC inverter (VFD); control providing variable feed rate from 15 - 70 FPM for heavy calibration; LED readout feed speed indicator. -- Microprocessor Control for: Conveyor bed positioning to high precision via keypad entry. -- Automatic electronic preset panel thickness gauge/micrometer. -- Automatic Air Jet blast cleaning system on both sanding heads.Top Machine Model: NT-KL-920 PRR-U -- 1st Head - Spiral Cutterhead: (8) Rows of 15 x 15 x 2.5 mm inserts carbide knives; (4) sides for rotation; low tool cost.Cutterhead: 7" (175 mm) Dia.; 50 HP motor.Segmented Chip Breaker: Before the cutterhead. -- 2nd Head - Contact Roller: 11" (280 mm) Dia.; 70 durometers; powered by 40 HP motor; running at 3,600 FPM belt speed.Sanding belt size: 85" x 37". -- 3rd Head - 3-1/4" Pneumatic Polishing Platen: Engineered as combination station; air-cushioned & adjustable in pressure to various grits and materials application; powered by 30 HP motor. -- Lifting & lowering Conveyor Bed: Motor 1.5 HP (includes auto. thickness setup device). -- Variable speed 7.5 HP inverter duty motor; integrated with AC inverter (VFD) control; variable feed rate: 15 to 70 FPM for heavy calibration; LED readout feed speed indicator. -- Microprocessor Control: For conveyor bed positioning to high precision via keypad entry. -- Automatic electronic preset panel thickness gauge/micrometer. -- Automatic Air Jet blast cleaning system on both sanding heads. -- Powered dropdown Conveyor between Bottom & Top machine.Features (includes both machines) -- Massive monoblock base: 3/4" Thick plate steel weldments. -- Large dia. roller hold-downs; ball bearing supported; 65 duro UV rubber are standard features. -- Automatic soft start of main motors (Y-Delta). -- Disc braking/emergency shut down protection for: Sanding belt breaking, non-tensioned sanding belt; and mistracking of sand belt. -- All motors & electrics are CE-approved. -- Electronic oscillating belt tracking system. -- Au

NORTHTECH - NT-SL2000XL, ...Straight Line Rip SawSpecifications: -- 20 HP Direct Drive Straight Line Rip Saw. -- 2" Arbor. -- Distance from column to blade: 18 in. -- Saw blade size: 10" - 14". -- 3-1/8" Cutting capacity. -- Glue Line Saw. -- Feed Motor: 1.5 HP. -- Feed Speed: 20 - 105 FPM.

NORTHTECH NT 1000-50HCVS Single-Sided 40" PlanerSpecifications: -- 40" Planer, 40 HP main motor, Helical Head, Adjustable bed rollers 15 mm x 15 mm x 2.5 mm Carbide Insert cutters. -- The spiral cutterhead provides a high chip removal rate, superior surface finish and low noise. -- Powerful 40 HP cutterhead motor makes this planer ideal for heavy-duty planing and meets high production requirements. -- Variable feed speed is mechanical variable from 0 - 90 FPM. -- Power elevation of the feed bed with "727 M Digital Table Adjustment" for fast accurate, and convenient thickness setting. -- Extra heavy rib reinforced cast iron table, surface precision ground. Equipped with: -- (4) Powered steel bed rollers. -- (4) Upper rollers. -- (2) Powered corrugated infeed rollers. -- (2) Powered urethane outfeed rollers. -- Upper and lower limit switches for opening control. -- (4) Dual 50 mm jack screws for raise/lower bed movement; 12" max opening. -- 2 HP Elevation motor with manual adjust. -- Rear E-Stop for added safety. -- Dual 6" dust ports requiring 1,000 CFM @ points of extraction.

//This machine is in an Auction on exfactoryauctions.com// //Link to machine: http://exf.ac/i5z NORTHTECH NT-EV-920RC DUAL HEAD WIDE BELT SANDER 2-Head wide belt sanding machine with 37" capacity. - Heads: 1st head: 8-1/4" Dia. grooved rubber contact roll, with 20 HP motor. 2nd head: Combination finishing platen with grooved rubber roller and polishing pad, with 15 HP motor. Two (2) infeed and outfeed spring loaded hold-down rollers; 2 HP variable speed feed drive. Sanding belt size: 37" X 85" and with electronic belt tracking. Motorized opening between the conveyor and sanding bed. Ammeters for measuring motor loads.