SNX nVISION C 1.5 SEMI-AUTOMATIC CONTOUR EDGEBANDER: -- Specifications: The nVision C1.5 Curved (Contour) Edgebander to allow 360° edgebanding to contoured (shaped) panels. The Standard banding machine includes banding and trimming stations with one set of cutting tools, one articulated vacuum arm, an edgeband coil stand, and one 8″ aluminum vacuum pod. Includes on-site installation and training, free phone support, operation manual, and one-year limited warranty.The machine uses standard EVA hot melt glue and can apply .5mm to 3mm thick edgebanding.Edgebanding is applied automatically as the part is advanced past the edgebanding workstations via turntable.Reduced learning curve/expertise for operation as operator simply loads part to vacuum turntable, then activates the edgebanding cycle. -- Working Capacity: The nVision C 1.5 can band Minimum material size 150 mm (6") diameter.Maximum material size 2,400 x 2,400 mm (94" x 94"); Maximum material weight up to 104.5 KG (230 lbs).Material thickness from 10 - 60 mm (0.4" - 2.36"); Banding thickness from 0.5 mm thin tape w/low temp adhesive - 3mm tape. -- Radii Capacity:Minimum Internal (inside) radius 11.1 mm (0.4375 - 7/16"); minimum external (outside) radius 30 mm (1.18") based on 1 mm thick edge tape. IMPORTANT: ALL minimum & maximum radii are affected by tape thickness, quality of adhesive and edgebanding being applied. Radius size dramatically affected by adhesive temperature and quality of edge tape; semi or rigid.NOTE: Panels can be irregular in shape but must conform to the min. tolerances of inner & outer radii and fit within the work area.Equipped with:Thermal-regulated glue pot heated via (1) 800 Watt heating elements with electronic temperature controls; holds up to 1 kG (2.2 Lbs) of granules. (2) Pressure rollers to copy the shape of the piece, automatic guillotine for coiled material 0.5 mm - 3 mm (0.02" - 0.11") thickness & 57 mm height (2.25"). Operator Interface: -- Faster processor and a more accurate encoder for more consistent tight butt joints. 15"; touchscreen monitor. Training & Maintenance videos on PC. Connect to the internet for service and updates. More user-friendly interface. Bar code capable (optional).The 15"; touchscreen monitor provides an intuitive control panel, while features like training and maintenance videos make it easier than ever to maintain and operate the machine. The optional bar code capability allows for seamless integration into modern production workflows, reducing the potential for operator errors.Features: -- Tape height guide. Aluminum infeed guides. Solid shoe holder. Adjustable pod height spindle. Digital readouts. Pneumatic enclosure. Laser upgrade.The new PLC interface enhances usability, while the machine is capable of edgebanding and trimming an inside radius as small as 7/16″. It features 18,000rpm ER20 collet-type spindles (top/bottom) and the same proven articulating vacuum support arm. The nVision C1.5 can band and trim

SNX nVISION System2 G2 CONTOUR EDGEBANDER + Optional Dual Telescoping Arms for simultaneous Contour Banding & Trimming: -- Specifications: Curved (Contour) Edgebander to allow 360° edgebanding to contoured (shaped) panels.Edgebanding is applied automatically as part is advanced past the edgebanding workstations via turntable.Reduced learning curve/expertise for operation as operator simply loads part to vacuum turntable, then activates the edgebanding cycle. -- Working Capacity: The nVision Contour Bander can band a minimum material size of 150 mm (6") diameter.Maximum material size 2,400 x 2,400 mm (94" x 94"); Maximum material weight up to 104.5 KG (230 LBS).Material thickness from 10 - 60 mm (0.4" - 2.36"); Banding thickness from 0.5 mm thin tape w/low temp adhesive - 3mm tape. -- Radii Capacity:Minimum Internal (inside) radius 80 mm (3.14"); minimum external (outside) radius 30 mm (1'18") based on 1 mm thick edge tape. &#9679 Edgebanding thickness 1 mm, min = R 30 mm &#9679 Edge thickness 2 mm, min = R 50 mm &#9679 Edge thickness 3 mm, min = R 80 mm &#9679 Panel thickness 10-60 mm with edge thickness 1 mm &#9679 Panel thickness 10-60 mm with edge thickness 2 mm &#9679 Panel thickness 10-45 mm with edge thickness 3 mmIMPORTANT: ALL minimum & maximum radii are affected by tape thickness, quality of adhesive and edgebanding being applied. Radius size dramatically affected by adhesive temperature and quality of edge tape, semi or rigid. -- Equipped with:(1) Thermal-regulated glue pot heated via (2) 800-Watt heating elements with electronic temperature controls; holds up to 1 KG (2.2 LBS) of granules. (2) Pressure rollers to copy the shape of the piece, automatic guillotine for coiled material up to 3 mm (0.11") thickness & 57 mm height (0.125" - 2.25"). -- Features: TRIAX 3-AXIS Laser System (patented) for tighter butt joints & easy length identification with closed parts without the need for additional length measurement.The Laser also detects a tight radius and will automatically slow the speed + resume the set speed when the detected radius has passed.The machine is also equipped with the foot pedal for manual control/intervention. Motorized turntable for automated edgebanding application to large panels.(2) "Heavy Duty" Articulating arms to support the parts during edgebanding and trimming. Arm has a large inter-changeable vacuum pod to secure panels during edging and trimming.NOTE: Panels can be irregular in shape but must conform to the min. tolerances of inner & outer radii and fit within the work area. -- Complete with: &#9679 Top & Bottom Trimming unit &#9679 Centralized control panel with Simple PLC Touchscreen Interface with individual controls for all stations to enable manual feeding of panels if desired &#9679 Banding station &#9679 Edgeband coil stand &#9679 Standard-size vacuum pod for articulated arm &#9679 80 mm dia. (3") dust extraction outlet &#9679 Foot pedal activation/de-activation control &#9679 Larger feed roller

SNX NVISION SYSTEM2 CONTOUR EDGEBANDER: -- Specifications: Curved (Contour) Edgebander to allow 360° edgebanding to contoured (shaped) panels.Edgebanding is applied automatically as part is advanced past the edgebanding workstations via turntable.Reduced learning curve/expertise for operation as Operator simply loads part to vacuum turntable, then activates the edgebanding cycle. -- Working Capacity: The "nVision" Contour Bander can band a minimum material size of 150 mm (6") diameter.Max. material size of 2,400 x 2,400 mm (94" x 94"); max. material weight up to 104.5 kG (230 Lbs).Material thickness from 10 - 60 mm (0.4" - 2.36"); banding thickness from 0.5 mm thin tape w/low temp adhesive - 3 mm tape. -- Radii Capacity:Minimum internal (inside) radius of 80 mm (3.14"); minimum external (outside) radius of 30 mm (1'18") based on 1 mm thick edge tape. &#9679 Edgebanding thickness 1 mm, min = R 30 mm &#9679 Edge thickness 2 mm, min = R 50 mm &#9679 Edge thickness 3 mm, min = R 80 mm &#9679 Panel thickness 10-60 mm with edge thickness 1 mm &#9679 Panel thickness 10-60 mm with edge thickness 2 mm &#9679 Panel thickness 10-45 mm with edge thickness 3 mmIMPORTANT: ALL minimum & maximum radii are affected by tape thickness, quality of adhesive and edgebanding being applied. Radius size dramatically affected by adhesive temperature and quality of edge tape, semi or rigid. -- Equipped with:(1) NEW Thermal-regulated glue pot heated via (2) 800-Watt heating elements with electronic temperature controls; holds up to 1 KG (2.2 LBS) of granules. (2) Pressure rollers to copy the shape of the piece, automatic guillotine for coiled material up to 3 mm (0.11") thickness & 57 mm height (0.125" - 2.25"). -- Features: TRIAX 3-AXIS Laser System (patented) for tighter butt joints & easy length identification with closed parts without the need for additional length measurement.The Laser also detects a tight radius and will automatically slow the speed + resume the set speed when the detected radius has passed.The machine is also equipped with the foot pedal for manual control/intervention. Motorized turntable for automated edgebanding application to large panels.(2) "Heavy Duty" Articulating arms to support the parts during edgebanding and trimming & to maximize production throughput. Arm has a large inter-changeable vacuum pod to secure panels during edging and trimming. NOTE: Panels can be irregular in shape but must conform to the min. tolerances of inner & outer radii and fit within the work area. -- Complete with: &#9679 Top & Bottom Trimming unit &#9679 Centralized control panel with Simple PLC Touchscreen Interface with individual controls for all stations to enable manual feeding of panels if desired &#9679 Banding station &#9679 Edgeband coil stand &#9679 Standard-size vacuum pod for articulated arm &#9679 80 mm dia. (3") dust extraction outlet &#9679 Foot pedal activation/de-activation control &#9679 Larger feed roller &#9679 QC Glue tank with sensor.

SNX - Coil Hub, ...Edgebanding Heater & Storage System: For straight-line and contour Edgebanders - Keeps banding at the perfect temperature. - Softens banding, making it more pliable. - Keeps banding at the perfect temperature. - Softens banding, making it more pliable. - Increases adhesion. - Decreases delamination issues. - Allows a cleaner guillotine cut. - Lessens the chance of chipping when trimming. This "CoilHub" also keeps the coils contamination-free, keeps the edgebanding easily accessible right at the machine, and can store up to (20) coils.

SNX nVISION System2 G2 CONTOUR EDGEBANDER + Optional Dual Telescoping Arms for simultaneous Contour Banding & Trimming: -- Specifications: Curved (Contour) Edgebander to allow 360° edgebanding to contoured (shaped) panels.Edgebanding is applied automatically as part is advanced past the edgebanding workstations via turntable.Reduced learning curve/expertise for operation as operator simply loads part to vacuum turntable, then activates the edgebanding cycle. -- Working Capacity: The nVision Contour Bander can band a minimum material size of 150 mm (6") diameter.Maximum material size 2,400 x 2,400 mm (94" x 94"); Maximum material weight up to 104.5 KG (230 LBS).Material thickness from 10 - 60 mm (0.4" - 2.36"); Banding thickness from 0.5 mm thin tape w/low temp adhesive - 3mm tape. -- Radii Capacity:Minimum Internal (inside) radius 80 mm (3.14"); minimum external (outside) radius 30 mm (1'18") based on 1 mm thick edge tape. Edgebanding thickness 1 mm, min = R 30 mm Edge thickness 2 mm, min = R 50 mm Edge thickness 3 mm, min = R 80 mm Panel thickness 10-60 mm with edge thickness 1 mm Panel thickness 10-60 mm with edge thickness 2 mm Panel thickness 10-45 mm with edge thickness 3 mmIMPORTANT: ALL minimum & maximum radii are affected by tape thickness, quality of adhesive and edgebanding being applied. Radius size dramatically affected by adhesive temperature and quality of edge tape, semi or rigid. -- Equipped with:(1) Thermal-regulated glue pot heated via (2) 800-Watt heating elements with electronic temperature controls; holds up to 1 KG (2.2 LBS) of granules. (2) Pressure rollers to copy the shape of the piece, automatic guillotine for coiled material up to 3 mm (0.11") thickness & 57 mm height (0.125" - 2.25"). -- Features: TRIAX 3-AXIS Laser System (patented) for tighter butt joints & easy length identification with closed parts without the need for additional length measurement.The Laser also detects a tight radius and will automatically slow the speed + resume the set speed when the detected radius has passed.The machine is also equipped with the foot pedal for manual control/intervention. Motorized turntable for automated edgebanding application to large panels.(2) "Heavy Duty" Articulating arms to support the parts during edgebanding and trimming. Arm has a large inter-changeable vacuum pod to secure panels during edging and trimming.NOTE: Panels can be irregular in shape but must conform to the min. tolerances of inner & outer radii and fit within the work area. -- Complete with: Top & Bottom Trimming unit Centralized control panel with Simple PLC Touchscreen Interface with individual controls for all stations to enable manual feeding of panels if desired Banding station Edgeband coil stand Standard-size vacuum pod for articulated arm 80 mm dia. (3") dust extraction outlet Foot pedal activation/de-activation control Larger feed roller

Combination Differential/Filling Machine SMARTCOATER with: 880 mm (34-1/2") Working/pass-through height; one of the best units ever produced. Dual purpose machine can be utilized as: -- 1) A standard differential Roll Coater for application of UV sealer or top coat material; as a differential Roll Coater the 1st application head is independently utilized to for precisely controlled application. -- 2) A Filling Machine for application of H2O or UV filling material to calibrate substrates with porous veneer; as a Filling Machine, both heads are utilized for application and reverse smoothing or pressing of UV filling material.Specifications: -- (2) Heads, 53" width cap. - 1st Head: 250 mm (9-3/4") Dia. rubber coated applicator roller with separate doctor roller; doctor blades are oscillating. -- 2nd Head: 245 mm (9-5/8") Dia. chromium coated smoothing/reverse roller w/separate chromium doctor roll; all heads are floating to compensate for calibration errors & minimize damages from oversize parts. -- Adjustable opening 0 - 100 mm (3-3/4"); thickness protection safety bar connected to pneumatic emergency lifting; EX-proof electrics on all motors. -- 2 HP Conveyor drive: Variable feed speed from 26 - 131 FPM; 1/2 HP variable RPM drive on doctor rolls and separate 3/4 HP drive on applicator & reverse rollers. -- Electrical power: 480 V, 3-Ph, 3.8 kW; 7 Amps.

SORBINI SMART COATER MF Single Head Differential Roll Coater;SORBINI - Single-Head Roll Coater, ... "SMARTCOATER MF" SeriesMachine Features & Benefits:Single-Head Roll Coater designed for smooth application.Conveyor belt made of: Solvent resistant material with automatic tracking rollers mounted underneath the application rollers (182 mm dia.).Application rollers (250 mm dia.) covered with Heavy Duty vulcanized rubber of different shore hardness for different applications & coating products.Heavy gauge chromed steel doctor rollers (173 mm dia.).Feeding belt, coating rollers, and doctor rollers are all driven by independent motors and inverter is controlled directly from the control panel.Self-leveling floating head for optimum application on uneven surfaces.Thickness control and indicator on the control panel.Different types of scrapers are available according to the coating product and type of application.Pneumatic pump for lacquer feeding and recirculation.Differential capability allows for rotation inversion of doctor rollers and for fine adjustment of the applied coating, particularly important for high quality top coats.Safety "Cleaning Mode" to facilitate and safely service the machine.Technical Specifications:Working width from 0 to 1,300 mm (0 to 51 in).Min. workpiece length: 305 mm (12 in).Speed range: 2 - 11 MPM (6-1/2 to 36 FPM).Power consumption: 4 kW.Compressed air required: 15 Nl/Min (0.53 CFM) exhausted solvent/air mix. Working side: Right.Electric equipment: Explosion proof.Footprint Dimensions: Length 898 mm (35 in.) width 3,282 mm (129 in.) height 1,674 mm (66 in.).

SORBINI TM/95-2F Flow Coater Specifications: -- 24" Coating width, 4" max. thickness, hand crank controls curtain thickness, (1) head gravity feed. -- 2 HP feed motor for variable feed speed from 90 - 350 FPM, (1) 1.5 HP circulating pumps, (1) stainless steel tank & return reservoir. -- Conveyor: 24" Wide, 60" Long at infeed, 72" long at outfeed. 34" long center belt.

CEFLA/SORBINI, VS 34/ACT/1600 - Top Only Panel cleaning machineEquipped with:One (2) Anti-Static ionization bar. One (2) soft horse hair brush, in opposite rotation to panels feed direction, 400 RPM brush speed.One (2) timed, compressed air blower Min. work piece length 290 mm (11.5";).Belt conveyor with variable speed feed from 3 - 16 MPM (approx 10 - 52 FPM). Hand wheel for thickness adjustment.

2022 CNC controller! Under power & ready to demo! 3-Axis CNC Vertical Milling Machine - Seller has outgrown and upgraded to larger capacity CNC Machining Center. - Table size 10" x 50" x 38” H - Travels: X-Axis: 31", Y-Axis: 17", Z-Axis: 23-1/2" - Quill travel 5" - Quill diameter 100 mm (3.94") - No. 40 Spindle taper - Variable spindle speeds 80 - 4,000 RPM - Rapid traverse 150 IPM - Distance from spindle nose to table (Maximum part height) 23-1/2" - Distance from spindle center to column face 19" - Maximum weight of workpiece 1,320 Lbs. - Maximum work capacities: 1" Drilling & Tapping mild steel & Milling (Metal removal rate/mild steel) 5 cu. in./min. - 5 HP Spindle motor - 560 in-oz Continuous torque D.C. servo motors & Precision ground ball screws for X, Y, & Z-Axes - YEONG DIEN Automatic lubrication unit Includes: - 2022 "PROTOTRAK SMX3" 3-Axis CNC Control/3-Axis Digital Readout (Control defines tool path based upon user defined part geometry), with Pentium PC-processor with 512 MB RAM, 10.4? Color active-matrix screen, Touchpad, (4) USB connectors, MICROSOFT "WINDOWS" Operating system, Program feedrate override & Tool path graphics - ALL MACHINE PARTS "MAXI TORQUE-RITE" Pneumatic drawbar, with 40 - 50 ft. Lbs. of torque - EKSTROM CARLSON "MISTIC MIST 1ST-2LC" 1 Gallon Capacity Coolant Mist Generator, with Adjustable air & Liquid control valve - WALDMANN "ROCIA.FOCUS" 600 Lumen 5,000 K Sealed Housing LED Work Light

SPEC AIR Model R-44SQ Dust Collector with Shaker Bag Cleaning, Abort Gate, Spark Detection, Rotary Air Locks and Relay Fan in a closed loop configuration. -- Overall Data: 46,000 CFM with approx. 6170 sq. ft. of cloth area consisting of (286) filter bags operating at 7.4:1 Air-to-Cloth Ratio (ACR). 'Can velocity' (upward) is 211 FPM. Polyester filter bags are 9" dia. x 110" long. -- Fan:/Motor: SPEC-AIR EB-44 Clean Air Fan with approx 44" dia. inlet/outlet, ground- mounted in an upblast arrangement. Fan can deliver 46,000 CFM @ 16" SP. Inspection door, and belt guard. Belt-driven by a TOSHIBA 200 HP High Efficiency (Inverter Duty), TEFC motor, 447T frame at 1780 RPM. -- Bag Cleaning: Via (2) Shaker motors with a lattice of tie-rods inter-connected to each row of bags. Bags are accessed from the top clean air plenum.Timer relay from low voltage controls for bag cleaning. -- Comes with: (2) Tapered hoppers separating the large particles, large access door, Backdraft Dampers adapted to (2) 32" filter inlets, lower hopper bottom each with Rotary Air Lock. Discharge from both RAL's is connected to a Material Handling Transfer/Relay fan into an enclosed container (not included) for continuous collection of waste. A return pipe from container makes this a closed loop configuration. Explosion doors. Safety ladder to top return air plenum.. Magnehelic differential pressure gage to monitor the condition of the filter bags. -- Construction: Heavy gage construction with reinforcing ribs and Flange-bolted in the middle easily allows units to transport into two units, ie 120" x 141".Return Air starts from filter outlet with adaptor to 44" dia. fan inlet. Discharge Silencer of fan outlet has a 44" Abort Gate returns air into building. -- Features: HANSENTEK Spark Detection system. Main electrical panel with pushbottons and controls. -- Includes: Filter housing and outside pipe is fully covered with insulation to minimize heat loss & reduce plant heating cost. -- Overall dimensions: 282"; Long x 120"; Wide x 317"; High. Weight approx. 20,000. Lbs. -- Note: Unit was moved in 2020 to current location, refurbished added installation.

SPEC AIR Model R120-26RD-OC Baghouse Filter Auto Shaker Type Dust Collector Loaded with features. -- Capacity of approx.15,500 CFM and the following features and components: -- EB-26, 60 HP SPEC AIR, Air Handling Fan , 15.500 CFM @ 16" SP mounted in a negative pressure configuration (clean air side) with return air and with automatic 26" dia. Abort Gate Damper according to NFPA-68-69 CODE. 110 volt actuated by the Spark Detection System. -- HANSENTEK AN104 Spark Detection/Suppressions system Per NFPA 64-68 and c/w BPS-9X4 Booster Pump & FLEXCON P2P20 Tank. -- 1,961 sq. ft. of filter area using (97) high efficiency Polyester bags. Operating at 7.9 to 1 ACR (Air to cloth ratio). -- 26"; Diameter Inlet & outlet duct. -- Tangential inlet with Backflow Damper, according to NFPA-68 CODE. -- Top mounted motorized bag shaker. mechanism powered by 1.5 HP. -- Rotary Air Lock with 96" clearance. (4) leg support steel frame & Safety access ladder. -- Explosion Venting Doors, according to NFPA-68 CODE. -- Filter Bag size approx. 9" dia. x 9' long, -- Inline 26" dia. Silencer muffler on return air duct. -- Ground mounted Belt Driven Fan complete with TEFC motor and inspection door. -- Features: 60 HP Soft Start Controller. -- ENGINEERED ELECTRIC Control Panel with starters and controls. -- Manometer gauge to monitor differential pressure (life) of filter media. -- Housing/Support Steel dimensions: 120" long x 120" wide x 32' high. Approx. 13, 500 Lbs. -- Some pictured pipe is included.

SPROUT Rotary Drum Dryer with Gas Burner;Complete with the following components: -- 7.5 Ft. x 24 Ft. Steel Rotary Dryer Drum. -- Natural Gas Burner (may be converted to LP) with 13.5 Ft. Refractory Lined Furnace Tube. -- Belt Drive with Gear Reducer and Electric Motor. -- Trunnion Bases complete with Forged Trunnion Wheels. -- Forged Trunnion Tracks (weld-on style) ...look like new. -- Vertical drop material Inlet Transition with Side Access Door. -- Rated for approx. 2 TPH water evaporation or about 4.5 TPH wood sawdust input. -- OPTIONAL ITEMS: &#9679 Receiving Bin with Airlock and Screw discharge Conveyor. &#9679 Material Input Screw Conveyor. &#9679 Main Fan.

VECTOR REVOLUTION 180 CNC CONTOUR EDGEBANDER + Vector Vision Upgrade: Numerically controlled automatic Edgebanding Machine precisely applies ABS & PVC edgebanding automatically to square or irregularly shaped parts as the banding head travels on a bridge gantry along the "X", "Y" & "Z" axis.Machine Features:The banding unit simultaneously rotates on a high precision "C" axis; AC Brushless Servo motors with digital drives and linear guides ensure high speeds & accuracy with a smooth acceleration-and-deceleration. -- NO PROGRAMMING required, extremely simple changing from one tape size to another, the operator only has to make simple adjustments like setting the start position, the glue height, feed the new width of tape and adjust the tape guide height. All else is taken care of by the machine. -- Cartridge Glue System, glue height is set by positioning a pin in a hole in the index ring setting for the glue dosing rod, standard positions are, 16 mm (5/8"), 19 mm (3/4"), 25 mm (1.0"), 28 mm (1-1/8"), 31 mm (1-1/4") eliminating any need for fine adjustment. -- Working Field:"X" Axis 139.7" (3,550 mm), "Y" axis 72" (1,830 mm), 0.63" - 1.57" (16 - 40 mm) min. - max. material thickness.0.79" (20 mm) Minimum external radius & 1.97" (50 mm) minimum internal radius, depending on the type of banding materials. 1 mm Minimum banding material thickness & 3 mm maximum banding material thickness. (NOTE: 1 mm PVC is not suitable for butt joints). -- Work Table:Phenolic worktable with embedded vernier scales in "X & Y" axis allows for simple & flexible positioning of 2 - stage vacuum pods. The worktable allows for single or pendulum processing with (2) 48" x 72" (1,219 x 1,828 mm) work zones for processing small to large parts. With average cycle times under two minutes, the contour edgebander consistently produces quality parts, including 360° lap joints.The work piece is supported by means of vacuum cups sitting on a large flat bed. This enables absolute flexibility in positioning pods to ensure the workpiece is held securely. Full vacuum is achieved with a 100 m³/Hr vacuum pump. The pump is mounted inside the frame of the machine reducing noise and avoiding airborne dust.Exact workpiece positioning is not critical, as the patented VECTOR Revolution 180 operating system is unaffected by panel position.This patented process is controlled by a simple and intuitive interface that doesn't require CNC programming. -- Edge Banding Unit:The VECTOR Revolution 180 uses a cartridge & nozzle glue extrusion system which is ideally suited to this contour banding application.The cartridge glue nozzle is a closed system which only heats the glue as it is used. The glue is not exposed to the atmosphere. This means there is no burning of the glue or dis-coloration & the original color of the glue & its properties are maintained.Another benefit of the glue nozzle system is its close proximity to the first pressure roller. This means that even when slowing for corners, the

VECTOR REVOLUTION 180 CNC CONTOUR EDGEBANDER + Vector Vision Upgrade: Numerically controlled automatic Edgebanding Machine precisely applies ABS & PVC edgebanding automatically to square or irregularly shaped parts as the banding head travels on a bridge gantry along the "X", "Y" & "Z" axis.Machine Features:The banding unit simultaneously rotates on a high precision "C" axis; AC Brushless Servo motors with digital drives and linear guides ensure high speeds & accuracy with a smooth acceleration-and-deceleration. -- NO PROGRAMMING required, extremely simple changing from one tape size to another, the operator only has to make simple adjustments like setting the start position, the glue height, feed the new width of tape and adjust the tape guide height. All else is taken care of by the machine. -- Cartridge Glue System, glue height is set by positioning a pin in a hole in the index ring setting for the glue dosing rod, standard positions are, 16 mm (5/8"), 19 mm (3/4"), 25 mm (1.0"), 28 mm (1-1/8"), 31 mm (1-1/4") eliminating any need for fine adjustment. -- Working Field:"X" Axis 139.7" (3,550 mm), "Y" axis 72" (1,830 mm), 0.63" - 1.57" (16 - 40 mm) min. - max. material thickness.0.79" (20 mm) Minimum external radius & 1.97" (50 mm) minimum internal radius, depending on the type of banding materials. 1 mm Minimum banding material thickness & 3 mm maximum banding material thickness. (NOTE: 1 mm PVC is not suitable for butt joints). -- Work Table:Phenolic worktable with embedded vernier scales in "X & Y" axis allows for simple & flexible positioning of 2 - stage vacuum pods. The worktable allows for single or pendulum processing with (2) 48" x 72" (1,219 x 1,828 mm) work zones for processing small to large parts. With average cycle times under two minutes, the contour edgebander consistently produces quality parts, including 360° lap joints.The work piece is supported by means of vacuum cups sitting on a large flat bed. This enables absolute flexibility in positioning pods to ensure the workpiece is held securely. Full vacuum is achieved with a 100 m³/Hr vacuum pump. The pump is mounted inside the frame of the machine reducing noise and avoiding airborne dust.Exact workpiece positioning is not critical, as the patented VECTOR Revolution 180 operating system is unaffected by panel position.This patented process is controlled by a simple and intuitive interface that doesn't require CNC programming. -- Edge Banding Unit:The VECTOR Revolution 180 uses a cartridge & nozzle glue extrusion system which is ideally suited to this contour banding application.The cartridge glue nozzle is a closed system which only heats the glue as it is used. The glue is not exposed to the atmosphere. This means there is no burning of the glue or dis-coloration & the original color of the glue & its properties are maintained.Another benefit of the glue nozzle system is its close proximity to the first pressure roller. This means that even when slowing for corners, the

This listing Is for a complete line that consists of a Flow Coating line that feeds into a cross transfer oven and back out on to an outfeed conveyor making a 180 degree circuit. The heat exchanger needs to be heated by means of a hot water boiler or similar. Maximum Part width: 305 mmSpeed range: 2 - 10 m/min.Pos. 1 - FEEDING BELT CONVEYOR:For feeding the batches into the flowcoater, Belt with marked area to built a gap for the angle transfer, Technical Data: length: 2300 mmPos. 2 - IMPREGNATION MACHINE VEN FLOW:For flowcoating of profiles in continious production with a waterbased impregnation (viscosity similar to water)The material is is sprinkled on the surface and remains for appr. 10 seconds. After this time a high pressure air knife nozzles will blow the acess materialfrom the surface. The whole cabin is built with fall to the side to collect the rest of the material. It is reused after passing a filter system. The cabin is built of stainless steel. The blowing off of the access material by air knife is effected by a high pressure fan.The machine comprises:1 conveyor system with spray protected roller system length 3000 mm1 sprinkling zone with two nozzle systems adjusted to reach the whole surface of the workpiece. length: 200 mm1 penetration area length ca. 1000 mm time of residence ca. 10 sec1 blowing zone with adjustable knife nozzles air supply with high pressure fan air flow adjustable by frequency converter length ca. 1000 mmair speed ca. 40 m/sec. material supply to supply the two sprinklers with fluid and collector for recovered material.workpiece tolerances:twist: max. 1° on the whole length, straightness max. 0,5mm deviation/m in horizontal and vertical weight distribution: evenly on whole length coating material: waterbased impregnation. Unstable components can not be repositioned when tilted.Pos. 3 - MOULDING ANGLE TRANSFER VEN TRANS 90°conveying from lengthwise direction to crosswise, comprising:1 excenter-transfer arms integrated into the driven infeef roller conveyor. The tacted transfer system allows a minimum distance between the singlemouldings on the following cross transfer system.Technical Data:length of roller conveyor: 4500 mmroller pitch: 185 mmnumber of transfer arms: 22spacing 185 mmtacting cycle: max. 30/min.Pos. 4 - MOULDING CROSSWISE V-BELT CONVEYOR:Mouldings are conveyed by means of various v-belts along the system. The unit is fitted with an insulation cover between the conveyor. A drying tunnel is fitted on top of the unit.Technical data:length: 4000 mmoperating width: 4200 mmnumber of belts: 22distance of belts: 185 mmoutfeed prepared for an additional angletransfer:position of driving shaft in the middlegaps for passing of the carriers of the angle transferPos. 5 - JET DRYING TUNNEL 70 °C:Made of sandwich elements with fire preventing insulation material. The even distribution of air over the full operating width is reached by using slot nozzles on the full width of the tunnel. One combined heating-, fan

VESTIL EHLT-2464-2-55 Scissor Lift Full featured electric hydraulic scissor lift tables are used by all types of manufacturing and warehouse facilities.Safety features: -- Electric toe guard to protect pinch points during lowering of the table. -- Internal safety velocity fuse to maintain platform height in event of hose or fitting failure. -- Maintenance prop, and upper travel limit switch to stop table at maximum height. Specifications: -- 2,000 Lbs. lifting capacity. -- 2 HP totally enclosed electric motor. -- Platform size 24" x 64". -- Lowered height 7", raised height 55". -- 24V AC push button hand control. -- Hydraulic component rating of 3,000 PSI.

VESTIL EHLT-4896-4-56 Scissor Lift Full featured electric hydraulic scissor lift tables are used by all types of manufacturing and warehouse facilities.Safety features: -- Electric toe guard to protect pinch points during lowering of the table. -- Internal safety velocity fuse to maintain platform height in event of hose or fitting failure. -- Maintenance prop, and upper travel limit switch to stop table at maximum height. Specifications: -- 4,000 Lbs. lifting capacity. -- 2 HP totally enclosed electric motor. -- Platform size 48" x 96". -- Lowered height 8", raised height 56". -- 24V AC push button hand control. -- Hydraulic component rating of 3,000 PSI.

VIET - S211 R+ KRT, 2-Head Wide Belt Sander43" Width. cap.: Drum and Combination head.Head Configuration:1st Head: 160 mm 6.3″ Helical grooved rubber drum. 25 HP motor2nd Head: 160 mm (6.3") Helical grooved rubber drum with a platen combination head., 25 HP motorSpecifications: -- Each heads are powered by a 25 HP motor. -- The heads can be programmed to pneumatically raise & lower along with the platen and do (3) sanding combinations (with the twist of a button). -- Digital height readout and a calibration unit to the left side of the conveyor. -- Conveyor speed is controlled via a variable frequency drive 2.5 HP . -- Max width: 43″. -- Max. height: 6-1/4". -- Variable speed conveyor belt drive from: 3 - 16 MPM (11 - 52 FPM).Equipped with & Features: -- Both heads are equipped with: 1,130 x 1900 mm (44-1/2" x 75"). -- Roller & pressure shoe holddowns. -- Pneumatic tension of sanding belts and feed conveyor. -- Load meter on main motor. -- Disc brake on main motor. -- Emergency stops front & back. -- Roller table extensions front & back.NOTE: This is an extremely low-hour 2012 BIESSE Viet S1 dual head 43″ calibrating Wide Belt Sander.

VIET (BIESSE) OPERA 5-3.3 XLL Denibbing Sander with 53" Width Capacity:53" Width cap. Denibbing Sander with a patented combination of rollers and rotating/oscillating discs make the VIET Opera Sanding Machine the ideal finishing solution for entry doors, cabinet doors, drawer fronts, sheet goods, shutters, face frames, furniture, and much more. Ideal solution for all sanding applications including whitewood, stain, and sealer coats. Head Configuration: -- 1st Unit: (11) Rotating discs with Slide out system for easy setup. 15 HP Electronic Inverter. -- 2nd & 3rd Units: 300 mm dia. Roller Brushes (Hub for 36 strips). Oscillating System with electronic 7.5 HP inverter. Specifications: -- Working Width: 1,350 mm (53.15"). -- Constant Pass Line TM (Fixed Table). -- Working Height Opening: 200 mm (7.87"). -- Laser Electronic Positioning for working thickness. -- Min. processing thickness 3 mm, Max. processing thickness 200 mm. -- (2) Longitudinal rotating brush-backed sanding rollers. -- 5" Rotating sanding discs. -- Forward speed 3-16 m/Min. -- Vacuum Table with 5.5 HP Motor, Electronic System, IPC Control. -- 50-Shore Rubber Conveyor. -- Front & Rear Extension Rollers. -- Emergency stop.Equipped with: -- IPC Touch-screen control: Simple & user-friendly "TOUCH SCREEN" IPC control with a color monitor. This control system supports the management of all machine parameters. -- PC processor provides control and feedback information to the machine in real time. -- The software version can be configured for right and left-handed operation. -- Text-free user interface; icons facilitate the operator's task. -- Optional rotating blower attachment at the back to blow off dust particles as items come off the machine. -- Includes matching transformer for 600 V to 460 V.