RODGERS - 40-A: Edge Sander (Non-Oscillating) -- SpecificationsNon-Oscillating; 5 HP - 1,725 RPM motor with: Tracking & tensions adjustments & magnetic switch; 10"-wheel drive. -- 6" Wide x 168" long belt; 6" x 74" steel platen. -- 11-1/4" x 50" Front table with: 10" Vertical adjustment.

ROSE GBUB-80 Glue-Bound Unit Breaker. Machine breaks the glue bond in a staggered stack of finger jointed material - see picture of material with the checkerboard end pattern. --Features -- Equalized Hydraulic squeeze, provides uniform load compression. --Hydraulic length change. Air operated Locking Pins on the Backstop Platen. --Backstop platen position indicator. --Simple manual controls for load length adjustment and crushing stroke on the control panel. --Heavy Duty Structural Steel Construction, Ease of Maintenance and Simple Operation (no cables).Does not use cables!Specifications: --Maximum opening is 16’-10"; for a single 4' x 4' x 16' unit. --Backstop Platen locks at 12" increments (2' minimum load length) --Pressure Platen, hydraulic actuated with 18" stroke. --Platen size 5' x 5' --5 HP Hydraulic Unit with a Pressure Compensated Pump (approx. 1 minute squeeze time) --Overall size approximately 5' x 25' x 7' high --480 VAC, 60 hertz, 3 phase, 30 ampsOptions: --10 HP hydraulic unit with approx. 30 second squeeze time, add $4,200 --Double unit capacity; crushes (2) 4' x 4' loads with 5' x 10' platen, add $19,700 --Automated Control Package with 2 Remote Controls for initiation of Pressing Stroke; Automatic open and hydraulic shut down; PLC Controls, automated load length adjustment with lighted indicators, add $ 7,400

Ripsaw Feeder with 32" wide feed rolls on 18" thru 28" roll centers; will feed 3' thru 16' lumber. With 24" of in-out fence travel; feed speeds from 50 to 150 FPM; 3/4 HP feed roll drive and 3/4 HP fence drive via gear motor with brake. -- Fabricated frame of structural steel with boots that allow +/- 1" elevation adjustment. 3-1/2" dia. steel feed rolls driven by a variable frequency drive for speed adjustment; rolls are canted to aid in holding stock against the fence. -- Powered fence with 24" fence travel is easily shifted via joystick control for stock alignment with the sawblades. -- With pneumatic powered gate to keep material from feeding until the operator initiates the feed sequence. -- Urethane covered idler pinch roll is attached to the fence and is powered down at the start of the feed sequence. When a photocell detects the board is clear of the gate, the pinch roll and gate will return to their normal position. Electrical control panel ready for connection to the power supply.

ROSE MACHINERY TRANSFER SYSTEM: PANEL RIPPER TO MOULDER INFEED OUTFEED TRANSFERA Rollcase will carry stock away from a LHI 72" Panel Ripper. When the stock reaches the far end-stop, a 6-Strand Transfer Belt will pop up and take the stock to a Lateral Chain Feeder (supplied by others). The lifting mechanism is triggered by photocells and powered by an air bag using plant air. When the stock clears the Rollcase, the transfer will return to the down position to receive the next batch of strips. Rollcase Specs:17' 0" long; 76" between frame; 1.9" dia. X 12 gauge rollers. Galvanized rollers are set high on 3" centers. 5-1/2" x 1-1/2" x 12 gauge formed steel channel frames; welded construction. 120 FPM maximum. Dual shaft w/jump chain; underhung drive; timing belt driven; 1 HP, 575 volt/3ph/60hz motor; less controls. With (3) H-style leg supports; 34" top of roller; adjustable 32" to 38", with knee braces. Fixed angle end-stop. Frame is powder coated blue; guards powder coated yellow. Transfer Specs:B/17 purple power twist belt; 36" strand centers; 10'-0" long. UHMW chain track; airbag lifting style; thru frame; 36" top of chain. With 1/2 HP Boston 575 volt/3ph/60hz motor with Boston reducer for 120 FPM; less controller; proximity switches to detect carriage position are mounted only; solenoid valve, mounted and plumbed; filter/regulator - mounted and plumbed. With central bearing lube. Frame is powder coated blue; guards powder coated yellow Electrical Controls:ROSE provides an Electrical Control & Cabinet that will control the above Outfeed Transfer System. Electrical Control will incorporate a fused disconnect for incoming power, transformer and power supply for control voltage, (4) variable frequency drives for the motors, a PLC to read input devices and control output devices, and pushbuttons/switches for operator control. The panel will be mounted and wired to the enclosed devices. Incoming power and other field wiring is by others. Two days startup assistance is included. Travel expenses will be billed at cost separately.Conditions:All gear-motors, mechanical equipment, limit switches, sensors or photoelectric devices as required for each item of this quotation, will be supplied and mounted. All pneumatic cylinders or other pneumatic power devices and their valves will be supplied and mounted. They will have connecting hoses and fittings installed. Filter/Regulator units will be supplied, mounted and connected by hose to the valves. Compressed air service to equipment is by others.Exclusions:This proposal describes the machinery to be provided by Rose Machinery Inc.. The equipment supplied by Rose Machinery Inc. is specifically limited to the items actually described in the itemized details of this quotation. Unless specifically mentioned herein, all other items and services are the responsibility of the Buyer. State or local sales taxes, or any permit or other fees that may be required are not included. All field wiring, plumbing, and installat

ROSE MACHINERY LCFCMS14 PANEL RIPPER TO MOULDER TRANSFER SYSTEM OUTFEED ROLLCASE: -- Outfeed Rollcase receives material from the LHI Panel Ripper at 47 1/4"; elevation and drops down to place the lumber onto the Transfer Chains at 42"; elevation. 66"; wide rolls are 2-12"; diameter steel rolls, snap in style on 12"; centers. Rolls are powered by a line shaft using round Eagle Belts and a 1-1/2 HP gear-motor. The conveyor will be fabricated from tubular and sheet steel and designed to interface with the Transfer Chains. The conveyor speed is 80-120 FPM to create a gap between courses exiting the Panel Ripper. The drop will be triggered when a photocell detects the leading end of the boards, creating a far side lumber line. A pneumatic cylinder provides lifting power. When the transferred boards clear the rolls, another photocell triggers the rolls to return to the up position. Stock length handled by the Outfeed Rollcase is from 6’ to 16’. Elevation adjustment is +/- 1";.TRANSFER CHAINS: -- Transfer Chains receive material from the Outfeed Rollcase. The Transfer Chains are fabricated from tubular and structural steel. There are (6) strands of 2060H conveyor chain approximately 17’-6"; CC long, leaving 11’ clear space to accumulate (2) layers of ripped strips. (2) sets of pin stops are incorporated to keep the layers separate. The conveyor is powered by a 1-1/2 HP gear motor. Conveyor speed is 90 FPM maximum. Elevation is 42"; +/- 1";. LATERAL CHAIN FEED TABLE (ROSE MODEL LCFCMS14): -- Standard duty low friction flat top steel infeed chains drive the stock to the fence. The fence is adjustable for alignment with downstream equipment such as a Moulder. (3) lower powered feed rolls are smooth steel and non-marking. The feed rolls and chains are controlled by adjustable frequency drives. (3) upper pinch rolls are 5"; diameter urethane. The first (2) rolls singulate pieces while (1) pinch roll keeps the board moving on the bridge. The pinch rolls are triggered by photocells. A PLC in the control cabinet cycles the outputs based on operator input. Operator controls allow for start and stop of the chains and rolls, the feed to be paused, the rolls to be reversed and speed controls. -- Fabricated structural steel frame -- Passline height 42"; +/- 1"; -- Stock width 2"; to 9"; -- Stock Thickness 1/4"; to 4"; -- Stock Length 6’ - 16’ -- Rolls include a variable feed rate from 60 to 300 FPM -- Feed roll drive is by a 3 HP gearmotor -- (6) infeed chains, each 50"; long, are driven by a 1-1/2 HP gearmotor -- Infeed chain's variable feed rate is 20 to 75 FPM -- 2-1/2"; bore air cylinders actuate the pinch rolls -- With 3/4"; fence adjustment. ELECTRICAL CONTROLS: -- Controls are incorporated in the LCF Cabinet for the above Transfer System. It consists of operator controls, (2) VFDs, and additional PLC I/O and programming. STARTUP: -- 2-days startup assistance is included. Travel expenses are billed se

ROSE MACHINERY HBR Horizontal Band RE-RIP SawThe Horizontal Band Re-Rip Saw is an effective and efficient means of ripping short blocks into as many as six (6) set rip widths. Rip widths are easily adjustable, as well as the setting for stock thickness.Advantages of the system: -- Compact, efficient use of floor space. -- Accurate cutting of rips with minimum tear-out. -- Short blocks, 4" minimum length, without taper problems. -- Straight through feed design, good for sorting. -- Minimum dust collection required. -- Single point scrap collection. -- One saw drive motor, requires less power. -- Safety, no kickback problems.Specifications: -- Five (5) rip widths - (6) optional -- 20 HP bandsaw drive -- 30" diameter band wheels, 2" wide face -- (2) 3/4 HP feed works drives -- 1-1/2 HP feed belt drive -- 1" to 6" rip width (independently adjustable in each lane) -- 10" maximum board width at maximum rip -- 4" maximum waste piece width -- 3/4" to 2" stock thickness (all lanes adjust together) -- 4" minimum stock length -- 36" maximum stock length -- 80 FPM feed speed -- 52" to 58" pass line height -- Motor starters and push buttons included, wired for 440 volt, 3 phase, 60 Hz (uses standard mag starters) -- An automatic band lubrication system is includedOptional Equipment: -- For SIX (6) LANES, add ...$5,600 (SORTER increases $3,700) -- Automatic machine grease lubrication system, add ...$ 9,200 -- Ergonomic overhead stock slide, add ...$ 5,600 -- Output conveyor and sorter for 5-LANEsingle side discharge, add ...$47,300 -- Output conveyor and sorter for 6-LANE single side discharge, add ...$51,100 -- Operator's platform, add ...$ 7,900 -- Optional voltage configuration: 220/380/440V, 50HZ, add ...$2,900 -- Start-up and training, add $1,000 per day plus expenses at costHorsepower Requirements: -- (1) @ 20 HP -- (1) @ 1-1/2 HP -- (2) @ 3/4 HPDust Collection: -- (2) outlets, 6" diameter, 5,200 FPM velocity @ 2,300 CFMCompressed Air Required: -- 90 PSI @ 1.4 CFM

ROSE MACHINERY BDH/LC/LCFT Automated Infeed SystemAutomated, high speed Infeed System for Gang Rip Saws of all makes and models and other similar machines. -- 5-Arm Breakdown Hoist - Electric hoist accepts loads 4' wide x 4' high x 4' - 24' long; 10 HP gear motor (with brake) powers the hoist and holds the load. -- Hoist actuated through foot switches for up & down; limit switches provide max. up & down positions; (5) lifting arms tilt load at 50° allowing layers to spill onto the takeaway conveyor; 16,000 Lbs. max. lift cap. -- Landing Chain - Features: (6) Strands of roller chain; powered by a 5 HP gear motor at 60 FPM nominal rate. -- Tail end constructed with integral slide, stock transits from Breakdown Hoist; head shaft & gear motor supported by tubular steel frame with bolts to allow for leveling at installation. -- Material stops at the head end so the operator can flip & grade each piece. -- Chain races fabricated from steel, UHMW PE wear strips on the top race and on the return race; conveyor is 42' long. -- Magnetic motor starter with foot switch for operator to start & stop of the chain. -- Lateral Chain Feed Table "LCF2013-20": Feeds material 3" - 10" wide x 4' to 24' long x 1" to 3" thick; variable 50 - 200 FPM Feed rate; adjustable fence throughout 3/4" range for alignment with the Rip Saw (or other machines). -- (6) 30" long, low friction steel flattop infeed chains for long life non-marking transport; 1 HP gear motor. -- (3) Powered smooth steel & non-marking feed rolls, 2 HP gear motor; rolls & chains controlled by variable speed drives. -- (3) Overhead pinch rollers, 5" dia., urethane covered; 1st (2) pinch rollers powered by individual 2-1/2" bore air cylinders to singulate pieces onto a 2' bridge; 3rd roller keeps the board moving on the bridge; pinch rolls triggered by photoelectric cells. -- Note: Fabricated frames and appropriate parts of the items in this quotation will be painted with (1) coat of industrial grade Shady Lane Green enamel; guards and appropriate moving parts painted with Safety Orange. -- All gear motors, mechanical equipment, limit switches, sensors or photoelectric devices, as required for each item of this quotation, are supplied and mounted; all pneumatic cylinders or other pneumatic power devices and their valves supplied and mounted; connecting hoses & fittings installed. -- Filter/Regulator units supplied, mounted, and connected by hose to the valves; Note: Compressed air service to equipment is by others.

For dumping (1) load at a time. Hoist is fabricated from steel tubing with a box cradle that pivots at the top. The cradle holds the box as it is pivoted up to 135° to the final dumping position. The cradle is pivoted with a hydraulic cylinder driven by a 3 HP hydraulic pump. The cylinder is manually energized via operator foot-switches. -- System includes all mechanical equipment, electric powered hydraulic pump, and (2) foot switches. All wiring and controls by others. ~ Accepts a standard 96" long X 60" wide X 60" high box.

For dumping (1) load of fingerjoint blocks at a time. Hoist is fabricated from steel tubing with a box cradle that pivots at the top. -- 3-Sided cradle will hold the box, pallet, OR unit when it is pivoted up to 135° to the final dumping position; cradle opening is 88" long X 48" wide X 50" high . -- A pair of replaceable forks hold pallets in place in the cradle. The cradle is pivoted by a hydraulic cylinder driven by a 3 HP hydraulic pump. The hydraulic cylinder is manually energized by the fingerjointer operator with foot switches. -- Scope of supply includes all mechanical equipment, electric powered hydraulic pump, and two foot switches. All wiring by others.

STEGHERR - BOF, ...Through Feed Arch MoulderAutomatically feeds arched or curved parts for profiling or sanding. Feeds & contours parts with a radius of 6" or more and a max. material height of 3-1/4". Specifications: -- Feeds & contours parts with a radius of 6" or more and a max. material height of 3-1/4". -- (1) 1-1/4" Horizontal spindle at 5.5 HP - 7,500 or 1,500 RPM for sanding. -- 5" - 6-1/4" Tool dia., 4" spindle length capacity. -- 0.33 HP Feed motor, forward & reverse variable feed speed from 3 - 26 FPM. -- Flexible mounted 5-roller system guides and feeds workpiece. -- Simple setup allows for rapid changeover of different widths, no changeover required when machining same profile onto variety of arch radii. -- Complete with: Overhead hood assembly and dust outlet.Machine is currently wired for 220 Volt / 3 Phase power.

2023 Stema "Alphard" CNC Machine for Drilling, Routing & Tenoning on Doors & Frames Description: CNC haunch/mortise/Tenon/dowel machine for cabinet doors, beaded face frames, full size door mortice/tenon, French miters, dowel insertion. X-Axis w/ 3200mm of Stroke 70 m/min Y-Axis w/ Ballscrew Movement 25 m/min Z-Axis, 25 m/min Ten-Position Automatic Tool Changer/Revolver Tool Changer Allows for Tenoning, Profiling, Mortising, Drilling Haunching Unit (for French Miter Product), 5.5 HP Motor Dowel Insertion Unit (8mm) Vibrating Dowel Hopper Glue Inserting Unit PC User-Interface w/ Windows 10, USB, & 19"; LCD Screen Pegasus Software Total Working Length 3200mm (120") Manually Adjustable Pneumatic Clamps Heavy Steel Frame

STETON - P85: Hydraulic Cold PressDual platen Hydraulic Cold Press. -- Platen size: 1,300 mm x 2,500 mm (51" x 98") Overall platen size. -- Side loading on: 98" side. -- 420 mm (16-1/2"): Max. daylight opening. -- Pressure from bottom: (4) 3.34" Diameter upstroke hydraulic pistons; 2 HP Hydraulic pump: 90 PSI.OAL: 122" L x 66" W x 84" H.Weight: 6,600 Lbs.

86" x 17' 4" Cap., 3-1/8" cutting depth, 7.5 HP - 3,450 RPM motor, 300 mm blade cap. with 30 mm arbor, 4,800 RPM blade speed; automatic motorized vertical and horizontal movement of saw carriage, (4) speeds 36 - 55 - 72 - 108 FPM; automatically moving back support, automatic STAR-DELTA starter; DIGITRON electronic digital measuring system for X- and Y- axis. -- Complete with: Retractable center shelf, adjustable flip down stops, repeat rip gauge with 23-1/2" cap., lower roller supports for easy positioning of panels, and integrated dust system with rear mounted dust bag.

STRIEBIG STANDARD 5192-A Vertical Panel Saw.Specifications: -- 6-1/4' x 14-1/12' Cap., 3-1/8" cutting depth, 4.5 HP motor, automatic STAR-DELTA starter; 300 mm dia. (11-7/8") blade with 30 mm bore - 4,750 RPM rotation. -- Equipped with: -- Shifting panel support grid, auxiliary support channel for tall & narrow parts, 12' retractable center shelf w/adjustable flip-down stop, repeat rip gauge with 5-11/12' cap. -- Complete with: -- Lower roller panel support system with brakes (4) each adjustable base & rear supports for free-standing installation.

STROUP 4' X 20' Cold PressSpecifications: -- 50" x 244" End Loading, Segmented, Bag press with motorized daylight opening. -- (2) Individually actuated, 50" x 122", segmented platens. -- Single air bag per platen with approx., 50 PSI specific pressure. -- Motorized adjustable daylight opening from 9" to 56". -- End loading with (2) rows of spring-loaded pop-up rollers in lower platen for easy loading/unloading of the press.

SULLAIR 10B-50 ACAC Rotary Screw Compressor (Open Type)Specifications: -- 50 HP - 1,770 RPM Motor, rotary screw air end, 100-110 max. PSI, approx. 180 ACFM; (2) asymmetrical lobe profile rotors only make contact on a lubricated pitchline to virtually eliminate cap. or efficiency loss. -- Equipped with: -- Tapered roller bearings on discharge and cylindrical bearings on inlet for high load carrying capacity. -- Pressurized fluid lubrication & cooling of Compressor with rigid piping & tubing; efficient 2-stage air/oil separation with replaceable element. -- Spin-on fiberglass fluid filter, Heavy Duty inlet air filter, cap. modulator stabilizes system pressure and matches output to demand (minimizes need for air receiver & reduces wear caused by start/stop). -- Includes: -- Electro-mechanical gauges & controls, air after-cooling.

SULLAIR ES8-30H/A 30 HP Single-Stage Fluid Rotary Screw Air Compressor, with 53,186 Run & 49,602 Load Hrs. (As of 11/2023) Specifications: Cap. 111 ACFM. Rated pressure 60 - 125/135 PSIG. Noise level 85 dBA. Equipped with: E-Profile rotor design air end. 30 HP 3,530 RPM Motor. Air-cooled aftercooler. SULLAIR “SUPERVISOR II DELUXE” Microprocessor controller & graphic monitor system, with LCD Display, Touchpad, Constant pressure & temperature readout of pressure, Power failure auto restart, & Automatic start/stop. CURRENCY NOTE: Negotiable Price is listed in U.S. Dollars.

SUPERBRUSH 24 Brush Sander from SUPERMAX TOOLS:SUPERBRUSH applications include but are not limited to: White wood sanding, de-nibbing, sealer sanding, primer sanding, UV roughing, metal graining/straight lining, metal de-burring, sanding/polishing solid surface material, scuff sanding, shutter sanding, de-glossing and de-stressing.Specifications: -- 24" Sanding width and 11" max. material thickness (height) and min. 1/32" with manual thickness adjustment; 5 HP main motor. -- Rubberized conveyor belt grips and pulls parts through the sander at 0 - 15 FPM. -- 1-1/2" Dia., rubber covered, infeed and outfeed rollers provide tension to support the belt over reinforced steel conveyor bed. -- Bristle contact gauge (depth gauge) included. -- RPM Gauge displays brush speed, variable 400 - 1,200 RPM. Machine Structure: -- Cast stand, zinc-plated steel bed, centerless ground column tubes. -- Ball bearings are sealed and permanently lubricated.

SUPERBRUSH 24 x 2 Double Brush Sander.SUPERBRUSH applications include, but are not limited to: White wood sanding, de-nibbing, sealer, and primer sanding applications, as well as UV roughing and reclamation projects. De-burring, graining, and polishing of steel, stainless steel polishing and aluminum finishing and solid surface materials. These sanders are well suited to shutter sanding, de-glossing and de-stressing.24" Sanding width, 11" min. part length and 4" max. thickness; 5/8" typical brush dia., 1-1/4" to 3" Typical Brush length; 3/32" per turn height adjustment, depth gauge included.Drive Motor: (2) 7.5 HP MotorsRubberized conveyor belt grips and pulls parts through the sander. via 0 -30 FPM variable speed feed system1-1/2" Dia., rubber covered, infeed and outfeed rollers provide tension to support the belt over reinforced steel conveyor bed.Bristle contact gauge (depth gauge) included.RPM Gauge displays brush speed, variable 400 - 1,200 RPM.Hinged Dust Hood with (4), 4″ vacuum ports, 1800 CFM min.Machine Design: Cast stand, zinc-plated steel bed, centerless ground column tubes.Ball bearings are sealed and permanently lubricated.Accessories: Casters, Infeed-Outfeed tables & DRO (Digital Depth Guage).

SUPERBRUSH 36 Single Head Brush Sander, 5 HP Drive Motor.SUPERBRUSH applications include, but are not limited to: White wood sanding, de-nibbing, sealer, and primer sanding applications, as well as UV roughing and reclamation projects. De-burring, graining, and polishing of steel, stainless steel polishing and aluminum finishing and solid surface materials. These sanderr are well suited to shutter sanding, de-glossing and de-stressing.36" Sanding width, 11" min. part length and 4" max. thickness; 5/8" typical brush dia., 1-1/4" to 3" Typical Brush length; 3/32" per turn height adjustment, depth gauge included.Rubberized conveyor belt grips and pulls parts through the sander. via 0 -15 FPM variable speed feed system1-1/2" Dia., rubber covered, infeed and outfeed rollers provide tension to support the belt over reinforced steel conveyor bed.Bristle contact gauge (depth gauge) included.RPM Gauge displays brush speed, variable 400 - 1,200 RPM.Hinged dusthood with (2) 4" ports, 1,200 CFM min. capacity Dust collection recommended.Machine Design: Cast stand, zinc-plated steel bed, centerless ground column tubes.Ball bearings are sealed and permanently lubricated.Accessories: Casters, Infeed-Outfeed tables & DRO (Digital Depth Guage).