SAS SCORPION ENGINE PULLER Model SC40 DescriptionIncrease cash recovery from your recycling operationsSAS Forks Scorpion High Speed Motor Puller – Scrap Yard Engine Puller – Auto Recycling Engine Puller – Excellent for self service yards processing vehicles before crushing.Generate revenue:Process end of life vehicles in less than 60 seconds.Pull scrap engines and transmissions in 30 seconds.30% more revenue by separating metals from bodies.1000% more revenue per lb. on wire harness from engine compartment and dash.80% more visibility with a direct line of site from the operator’s window through the forks.Cycle time less than 15 seconds from park to full extension.Serviceable for long life. Replace blades in 3 hours or less.estimated only.Engineered & built for optimum performance:Engineered tough for continuous prying and durability.Hardened pins and bushings and grease-able pivot points for extended service life.Hydraulic hoses and cylinders are protected to minimize potential damage from sharp objects.Built with high strength blades and carriage skid plates for extended service.Clean up of ground debris is a snap with center plow blade.Speed is paramount in this design. Operator uses grapple from the cab, no torches, no personnel needed to hook up chains to pull or move engines. Safer, quicker and less costly removal of engines and transmissions.

Saturn Model 36x20 Slow-Speed Shredder --36" long x 20" wide chamber opening --1/2" knives. -- KYB MRH-30-SW2 hydraulic system powered by a 50-hp three-phase electric motor. --Comes equipped with stand and controls. -- Excellent for plastic, E-scrap, rubber, small tires, paper, cardboard, light metals.

SAVI HFK-250 Veneer Guillotine; General Specs: -- 102.4" (2,600 mm) Width cap., 4" daylight opening, hydraulically operated knife, 4 HP Leroy-Somer motor powers hydraulic unit with reservoir. -- Originally fitted with motorized parallel fence with 0.5 HP two speed gearmotor drive, push button operated, adjustable from 1" - 50" with magnified tape reader in front of machine. -- Equipped with: 2nd Cut feature with automatic reset, laser guide line light, photoelectric barrier guard for knife & hold-down beam, 2-hand operation of knife cycle. -- Note: Rear fence has been removed or modified. Shaft has chain/sprocket.

SAWSTOP - ICS 73230, ....Table Saw w/Safety "Stop Feature"Specifications: -- 10" Blade cap.; 7-1/2 HP motor; 3-1/8" depth of cut @ 0°; 2-1/4" depth of cut @ 45°; 13/16" max. dado width; 5/8" arbor dia. -- Features: -- Enclosed cabinet; Heavy-Duty belt drive; cast iron trunnions; SAWSTOPS's revolutionary flesh detecting safety mechanism. -- Includes: -- 52" "T-Glide" rip fence system; side support table and laminated top; 4" dust collection port; magnetic contractor motor control; main power switch with removable lock-out key. Actual model is: "ICS 73230"

5 HP motor with 8" or 10" blade cap. -- Features: SawStop Safety System, blade stops and retracts on accidental contact, protection is always on, performs continuous self checks, invisible protection, does not interfere with work, compatible with all standard blades; works on all woods and non-conductive materials. -- Includes bypass switch for cutting metal. European style riving knife to minimize kickback; Low profile blade guard for narrow cuts; Quick-change mount for guard and riving knife ÷Large start/stop paddle for hands-free shut off; Main power switch with removable lock-out key; Magnetic contactor motor control; Blade shroud for improved dust collection; Zero-clearance insert; Extra heavy castings ÷Widely spaced trunnions; Infinitely adjustable trunnion assembly for precision alignment. -- Also includes: Vertical slide blade elevation for increased stability; Long-lasting V-ribbed belts; cast iron handwheels; Two access doors in cabinet; Powder-coated cabinet.

SCHELLING FM-H 330/330 Automatic Panel Saw 129.9" (3,200 mm) Cutting length, 3.3" (85 mm) max. saw blade projection.Specifications & Features: -- 11 kW (15 HP) main & 1.6 kW (2 HP) scoring motor. -- Variable saw carriage travel speed from 0 - 262 FPM (80 MPM), constant return of 262 FPM (80 MPM). -- Electronically controlled overhead program fence with grippers, rack & pinion driven on both sides, forward speed from 0 - 262 FPM (80 MPM), return speed of 262 FPM (80 MPM); (6) Clamps open up to 3.9" (100 mm). -- 1,500 mm Long crosscut fence (front-to-back), (2) side/crosscut aligners for up to 87" crosscuts, (1) in front & (1) behind pressure beam. -- SCHELLING "COMPOSER" operating system; on-board SCHELLING optimizer, color monitor (displays cutting dimensions & patterns w/moving graphics), self-diagnostic, data input by keyboard & mouse or direct downloading from office PC is possible. Complete with: -- (3) Front mounted air float tables for moving panel from rip position to crosscut position; fully enclosed for safety with man-height sheet metal panels & wire screen windows.Specifications subject to verification.

SCHELLING FXH 430/410 FRONT LOAD, AUTOMATIC PANEL SAW: -- Specifications:169" (4,300 mm) Cutting length & 167" (4,250 mm) pull back; 3.9" (99 mm) max. saw blade projection, 23 HP (17 kW) main & 3.5 HP ((2.6 kW) scoring motor. -- Saw Carriage: Electronically controlled saw carriage with rack & pinion drive; variable travel speed 1 - 394 FPM (1 - 120 MPM), constant return of 394 FPM (120 MPM). -- Pusher Fence: Electronically controlled overhead pusher fence, rack & pinion driven on both sides; (9) Gripper clamps that open up to 3.5" (90 mm). -- Forward speed 0 - 262 FPM (0 - 80 MPM), return speed 262 (80 MPM) FPM; travel via brushless AC Servo Drive -- Operator & Machine Control:PC Front-end with Schelling "MCS" + Windows "NT" operating system.17" Color display with SVGA resolution (displays cutting dimensions & patterns w/moving graphics); virtually unlimited storage capacity, standard keyboard & mouse.Ethernet card; 128 MB Ram, 56K modem. Integrated graphical self-diagnostic, remote diagnostics by the factory is possible via dedicated phone line; data input by keyboard or possible direct downloading from office PC.SCHELLING "MCS" software displays simulation of patterns before actual cutting; graphical representations of cut-to-size parts in production shows the operator what to do in "real time". -- Complete with:2,300 mm Long crosscut fence (front-to-back), (2) automatic side/crosscut aligners for up to 87" (2,210 mm) crosscuts, (1) in front & (1) behind pressure beam cut line.(3) Front mounted air floatation tables, each table 24" x 83" (609 x 2,108 mm), rear of machine fully enclosed for safety with man-height safety fencing. -- Actual Model is SCHELLING FXH 430/410

SCHELLING FM-430/410 CNC Front Load Panel SawSpecifications & Features: 169" (4292 mm) Cutting length & 165.3" (4,200 mm) pull back, 3.75" (95 mm) max. saw blade projection; 25 HP (19 kW) 4,100 RPM main & 3.4 HP (2.5 kW) 5,600 RPM scoring motor. -- Equipped with: Variable saw carriage travel speed from 0 - 278.8 FPM (85 MPM), constant return of 278 FPM (85 MPM). -- Electronically controlled overhead program fence with rack & pinion driven on both sides; forward speed from 0 - 278 FPM (85 MPM), return speed of 278.8 FPM (85 MPM); equipped with (8) gripper clamps (open up to 5" (130 mm). -- Features: SCHELLING "COMPOSER" IBM-AT Compatible Computer Control; aftermarket color monitor (displays cutting dimensions and patterns w/moving graphics) , self-diagnostic, data input by keyboard; onboard optimization program. -- Complete with: 2-3/4" to 87" (2,200 mm) Long side/cross-cut aligning zone, (1) aligner in front & (1) behind the cut line. -- (3) Front mounted air float tables for moving panel from rip section to the cross-cut section, (2) movable and (1) fixed; each with their own blower. -- Rear of machine fully enclosed for safety with man-height sheet metal panels & wire screen windows. T

--In Auction--Starting bid: $100-- Schuetz Tool Bladder Press Specifications: (2) Shuttle tables, approx. 55” x 106” press capacity. Hot air design with 3mm silicone membrane to press veneer into profile, typical cycle time 3 minutes using proper glue that sets at 200°F. Can use PVA which would extend cycle time to approx. 15 > 45 minutes depending on the actual glue mix used to achieve 80%+ cure strength. Includes Hydraulic Pump. SPECIAL NOTE: Fully operational, however, need 4 or 5 heating rods replaced, new rod parts are included for you to install ( don't have the capability to remove them). The current average operational temperature is 150° F. NOTE: Above specs are taken from literature and thought to be accurate. As always please take advantage of the inspection period to verify. Items seen in the background are NOT a part of this Lot.

Schuetz Tool Bladder Press Specifications: (2) Shuttle tables, approx. 55” x 106” press capacity. Hot air design with 3mm silicone membrane to press veneer into profile, typical cycle time 3 minutes using proper glue that sets at 200°F. Can use PVA which would extend cycle time to approx. 15 > 45 minutes depending on the actual glue mix used to achieve 80%+ cure strength. Includes Hydraulic Pump. SPECIAL NOTE: Fully operational, however, need 4 or 5 heating rods replaced, new rod parts are included for you to install ( don't have the capability to remove them). The current average operational temperature is 150° F. NOTE: Above specs are taken from literature and thought to be accurate. As always please take advantage of the inspection period to verify. Items seen in the background are NOT a part of this Lot.

SCHUTTE PULVERIZER COMPANY - Model 40 HZF, ...HammermillComplete with the following major components & features: -- Integrated 18", 4,000 CFM Blower. -- Mellott Vibrating Conveyor -- Main drive motor: 75 HP -- Hammer width approx. 1-1/4" wide. -- 3-1/4" Shaft. -- 24" Dia. Rotor and a tip speed of 22,600. -- 17-1/2" Rotor width. -- 3/4" Main chamber steel.MANUFACTURER'S STATED KEY FEATURES:&#9679 Heavy-Duty plate construction with replaceable liner plates. &#9679 Heavy-Duty grates available in a variety of sizes. &#9679 Heavy-Duty rotor assembly. &#9679 24" dia. x 3" thick flywheel. &#9679 Built-in fan conveys material up to 50' vertically and 100' horizontally.&#9679 Reversible anvil. &#9679 2-Way reversible "raked" hammers pull wood in without feed rolls. NOTES: &#9679 The" HZF Series" Horizontal Trim Scrap Grinder is a high-speed, high production Grinder designed specifically for processing longer lengths of wood scrap such as: Rippings, edging, and trim blocks. Available in (4) standard sizes from 10" to 36" wide.&#9679 Each model features a built-in fan driven off of the main mill shaft, saving energy and valuable floor space while also significantly increasing production.

SCHUTTE 280.100 HAMMERMILL -- Type 13100P -- Rotor 24" dia. x 48" wide -- Housing 3/4" thick -- Shaft speed 3,600 rpm -- Heavy duty, statically and dynamically balanced rotor -- (96) Standard notched heat treated hammers 3/8" thick -- Also included; two screens -- Motor 125 HP -- Applications; Planer shavings, dry wood chips, etc. etc.

SCHUTTE-BUFFALO 15 Series, Model 15300 Wood Grinder;Complete with the following components and features: --Carbon Steel Construction. --Rotor approximate 44" diameter x 72" wide. --Approximately 3" wide Swinging Hammers, tip speed 20,700. --Top feed, bottom discharge. --Bottom screen approximate 5040 square inch area. --Clam shell housing. --500 HP, TEFC, 3/60/460 volt, 1785 RPM drive Motor with coupling and shaft guard. --Mounted on a heavy-duty steel Factory Frame. --NOTES: Largest model of the 15 Series. &#9679 Machine weight 16,000 Lbs.

SCHUTTE BUFFALO - Model WA16L, ... HammermillModel# WA16L, 3500 RPM, with filtration system and multiple grates for destruction sizes. -- It also includes Electrical panel. -- This system is apart and palletized. All you have to do is pick it up and transport it to you. -- System was in perfect working order when it was taken apart and palletized for transport. -- The system is perfect for the destruction of computer hard drives and different types of media.

SCM M3 Multi-Blade Dip Chain Gang Rip SawSpecifications: -- 300 mm (11.81") Width cap. -- 110 mm (4.33") Max. depth of cut. -- 8-3/4" Throat depth. -- 390 mm (15.35") Min. stock length. -- 200 - 350 mm (7.87" - 13.78") Blade diameter. -- Arbor dia. 70 mm (2.76"). -- Table size 750 x 1,530 x 750 mm H (29-1/2" x 60.24" x 29-1/2" H). -- Blade speed 4,200 RPM. -- Feed speeds 6 - 48 MPM (19 - 157 FPM).Equipped with: -- 44 kW (60 HP) - 3,554 RPM Blade motor. -- Variable speed drive feed chain motor. (2) Upper infeed & (2) Upper outfeed 4" Dia. rollers, Automatic chain lubrication. -- Top & bottom anti-kickback fingers. -- Main dust hood, with 200 mm (7.87") Dia. outlet. -- 40"; x 2-3/4"; H Adjustable infeed fence. -- Motor load meter.Complete with: -- Operation & Maintenance Manual. -- Tooling (As pictured).

SCMI OLIMPIC S1000 T-ERL EDGEBANDER (W/PRE-MILL & CORNER ROUNDING) -- Specifications:Edge Capacity, 0.4 to 15 mm (0.016 to 5/8") for strip feeding. -- Panel Capacity, min. width 50 mm and 140 mm min. length, (2.0" and 5-1/2"). Panel thickness min./max. 8 - 60 mm (3/8" - 2-3/8"). Equipped With:&#9679 Adjustable In-feed Fence: Manually pre-set with digital indicator and pneumatic panel spacing device. -- Pre-Milling Station, RT-E: Spindles 2 x 5.25 HP, 12,000 RPM, (1) with PLC controlled jump action and manual digital indicators positioning and Diamond Cutter-heads. -- Anti-Adhesive Spraying System: Top/Bottom, positioned prior to the Pre-Milling Unit, it prevents glue buildup on the work-piece surfaces. It consists of (2) independent spray nozzles, and a tank for anti-adhesive liquids. -- Automatic Strip & Coil Feed Magazine: For straight edges and 3 mm guillotine for coils. -- Gluing Station, Vc/1000: For EVA (Hot Melt) with Teflon coated glue tank and quick disconnect to change glue tanks fast if needed. Heat-up time approx. 10 Min. -- Pressure Section: Servo motor positioning, (4) pressure rollers, first larger, Teflon coated and powered. Workstations:&#9679 End Trimming Station K-SEL: Front & rear 2 x 0.5 HP, 12,000 RPM motors mounted on THK guides, swivels 0ø - 15ø, rapid set up between straight and angled cutting with the automatic swivel cylinder. -- Flush Trimming Unit, Rsp: Top/Bottom, 2 x 1.5 HP, 12,000 RPM with 2 pre-set pneumatic positions, flush and overhang, remote pneumatic in/out positioning. -- Bevel/Radius Trimming Unit, Ri/S: Programmable, servo motor positioning, 2 x 1.0 HP - 12.000 RPM motors for change-over on the fly. -- Corner Rounding / Trimming Unit, Round-K: For additional top & bottom trimming of linear an/or vertical leading & trailing corner when edgebanding all (4) sides, 2 x 0.8 HP - 12,000 RPM motor. Comes with (2) pre-set pneumatic positions to allow to go from thick to thin pvc automatically. -- Profile Scraping Unit "RAS/1000": Top/Bottom with (2) indexed manual pre-sets. Large dia. copy wheels for max. accuracy and pneumatic in/out positioning. -- Glue Scraping Unit, "Rca/2c": Top/bottom flat glue scraper with pneumatic positioning through controller and air-blow off nozzle to keep the knifes clean. -- Buffing Unit "SPN": Top/bottom, oscillating 2 x 0.25 HP - 3,000 RPM motors, tilting up to 12°. -- Hot Air Unit: Single blower with adjustable heat range and directional heat shield for top/bottom coverage. Restores color luster on thick pvc edging materials that my be lost during the edge scraping process.Controls: -- Startouch Controller, 12" color touch screen, swivels 270° at in-feed of machine. Capable to store (100) programs, (6) at the touch of a single key. Graphical display of all working units. Tracks production data, diagnostic information and monitors maintenance schedules. Complete With & Features: -- Feed-speed, 40/60 FPM, 1 x 2.5 HP feed drive motor, 200 Hz frequency inverter for all

SCMI SIGMA PRIMA 50 FRONT LOAD, AUTOMATIC PANEL SAW: -- Specifications: Working cap:149.6" (3,800 mm) Max. rip cut cap. 125.9" (3,200 mm) pusher stroke; 1.96" (50 mm) max. saw blade projection; 12 HP (9 kW) main saw motor (3,900 RPM); 2 HP (1.5 kW) scoring saw motor (6,300 RPM).Main blade diameter: 11.8" (300 mm), Main blade arbor diameter: 80 mm; Scoring blade diameter: 6.37" (160 mm), Scoring blade arbor diameter: 55 mmAutomatic exclusion of scoring unit when motor is in off position. -- Saw carriageFeed speed 0 - 327 FPM (0 - 100 MPM), return speed 327 FPM (100 MPM),Automatic saw carriage lubrication, balanced on hardened cylindrical guides; external score saw adjustment, THK guides for vertical saw movement. -- Pusher Fence:Feed Speed 0 -230 FPM (0 - 70 MPM) forward speed, 230 FPM (70 MPM) reverse speed;Programmable rear fence with (7) material gripper clamps, rack & pinion movement,Grippers fit into a slotted pressure beam for positive material control during the final cut. -- Operator & Machine Control:PC front-end with: SCM Real time "WinCut" + Windows "7 Professional" operating system; Pentium 300 MHz, 6.4 GB hard drive, 64 MB RAM,17" color super VGA flat screen monitor, on-screen diagnostics & production reports; (2) serial ports & (1) parallel port, spacing available for networking cards. "Cutty" optimization software is included which allows: 30 lines per program, 300 max number of pieces per line, and 3 cutting levels. -- Complete with:Side alignment device: Min. part width 2.36"; Max. part width 48"; Rear support rails with rollers;(1) Front fixed air table 98" x 24" (2,500 x 609 mm), (2) Adjustable air tables 59" x 24" (1,500 x 609 mm).Plastic safety guards; emergency stop bar; enclosed cutting area; triple dust collector outlet. -- Actual model is SCMI SIGMA PRIMA 50.

SCM Sandy 900-RRCS-135 Wide Belt Sander (3 ) HeadsWidth cap 53", Drum, Drum , PlatenHead Configuration:1st Head :Planer Head2nd Head: Grooved Rubber contact Drum 15 HP3rd Head: Superfinishing Unit: Provides uniform finish using a Chevron belt and an electronic pad, 15 HPSpecifications -- Working Width: 1,350 mm -- Min/Max Thickness to Be Machined (with Mobile Table) 4 - 170 mm; Min/Max Thickness to Be Machined (with Fixed Table): 4 - 200 mm -- Sanding Belt Width/Length: 1,370 & 2,620 mmEquipped with & Features: -- Chevron belt and an electronic pad, eye-S Control: allows easy and intuitive programming with an LCD display and touch-screen function. -- Unskilled Operator Friendly: Stores up to 120 work programs for commonly used machine settings.

SCM Sandy 10 -RCS-110 Wide Belt Sander (2) Heads43" Width cap. Drum, Combination HeadHead Configuration:1st. Head: 7" diameter corrugated metal roller for calibration 35 HP ( Drives both Heads )2nd Head: Combination head with 7" dia. contact roller (spiral grooved rubber covered); air/jump finishing platen controlled with timers to eliminate any rounding on leading & trailing edges of the panel, 2" wide platen.Specifications --103" long x 43" wide Abrasive belts --Air tracking, floating & rigid bed for sanding of veneers & solid panels; infeed & outfeed spring loaded holddown rolls -- Minimum workpiece length 16" --Thickness capacity 6.25". --Separate 2.5 H.P. variable speed feed motor delivering feed speeds from 15 to 70 FPMNote: The seller has 20 boxes of various sandpaper belts (80 – 150 grit) that will be included.

SCM TECH Z 30 CNC MACHINING CENTER (W/ATC/BORING): -- Specifications:Working Field "X" axis 120" (3,050 mm); "Y" axis 52.7" (1,340 mm) for routing & 44" (1,118 mm) for boring; "Z" axis stroke 7.8" (200 mm); max. material thickness 3.9" (100 mm). -- Positioning Speed:"X" & "Y" Axes are 197 FPM (60 MPM); "Z" axis is 72 FPM (22 MPM).Axes positioning by: AC Brushless motors and YASKAWA drives; high precision ball screw drive system in "X", "Y". "Z" Axes;All axes ride on prismatic guideways & sliding blocks. -- Worktable:(6) "TV" Tubeless mobile support rails, (2) vacuum pods per rail; (4) pneumatic lifter rails for heavy panels.(6) Pneumatic pop-up backstops, (6) pneumatic pop-up front stops; (2) pneumatic pop-up side stops.LED Display positioning assistance for the support rails & vacuum pods; (2) independent working fields. -- Boring Head:3 HP (2.2 kW) motor - 4,000 RPM; (15) independent vertical spindles: (8) Spindles in "X" & (7) spindles in "Y".(6) Horizontal spindles (2 + 2) in "X" & (1 + 1) in "Y-axis".(1) X-axis grooving saw with 100 mm dia. blade - 6,000 RPM. -- Machining:(1) 10 HP (7.5 kW) Electro-spindle router with: HSK F63 Adaptor; variable speed from 1,000 - 24,000 RPM, max. torque achieved at 12,000 RPM.Static inverter for stepless speed & rapid shutdown rotation.(1) 6-Position ATC tool plate mounted on the on the machine for "on the fly" ATC; max. tool weight is 8 kG (17.6 Lbs). -- Operator & Machine Control:PC Front-End with: SCM "UNIVERSAL K2" + "Xilog Plus" + Windows "XP" Pro Operating System; 15" CRT color display, CELERON 2 GHz processor, enclosed in air-conditioned cabinet. -- Complete with:(1) 100 m³/Hr Vacuum Pump; automatic lubrication system; "BUMP STOP" safety system. -- Actual Model is SCM TECH Z30 R6