VIET S1 223 2620 1350 mm (53.15") 2-Head Wide Belt Sander, with Combination HeadSpecifications: -- For wood, veneer, & sealing. -- Thickness cap. 3 mm - 160 mm (0.12" - 6.30"). -- Variable feed speeds 3 - 16 MPM (10 - 52 FPM).Equipped with: -- 1st Head: Grooved rubber-covered steel contact roll, 25 HP Motor with Brake & Inverter, Quick set abrasive thickness setting, Electro-pneumatic "on/off" movement. -- 2nd Head: "KOMBI KRT" Combination head, with Grooved rubber-covered steel contact roll, Electro-pneumatic "On/Off" movement, Electronic segmented platen with 42-Section Reading beam at infeed, & 15 HP Motor with Brake & Inverter. -- Segmented rubber infeed hold-down roll, Segmented rubber hold-down roll between heads, & Segmented rubber outfeed hold-down roll. -- 1,380 mm x 2,620 mm (54.33" x 103.15") Abrasive belts. -- 54"; W Vacuum feed belt, 2 HP Feed motor with Inverter, 4-Roll Infeed & outfeed extensions, & 3 HP Blower. -- Control, with Touchpad, LCD Display, & (2) Motor load meters.EQUIPMENT NOTE: Seller states belt sensor is faulty and needs to be replaced and contact rolls have some wear spots. Potential buyers are welcome to inspect under power.

Biesse Viet S1 223 RKRT VN ( S1 223 2620) Sander2 Head 53" width cap Drum, Combiation ( Platen ) HeadHead configuration1st Head -- Steel Roller, Quick Set abrasive Thickness setting, Electro-pneumatic, "On/Off" movement2nd Head -- Kombi Drum/Pneumatic Sectional Platen -- Front roller on this combo head has Electro-pneumatic "On/Off" movement -- Electronic Segmented Platen controlled by reading bar at front of machine Equipped with & Features -- Inverter controlled. -- Can be used for wood, veneer and as a sealer sander -- Linear belt cleaner (Pneumatic) Feed Belt (54' wide) -- Vacuum Table with 3hp vac blowe -- Touch Screen control

VIRUTEX - EB 25: Hot Air EdgebanderFor preglued PVC, veneer and melamine laminate coil stock; 0.4 - 1.0 mm edge thickness; up to 65 mm panel thickness cap.; automatic coil & single edge strip feed.Equipped with: -- Thermostatically controlled hot air blower; 3,300 Watts for up to 500° C temperature; (2 - 3) Min heat up time. -- Guillotine type front & rear end trim (with fast speed, flying knife); top & bottom flush trims with single motor drive to cutterheads. -- Overhead belt type feeder; 15 FPM feed speed. -- Mounted on machine base with panel support table.Includes: Used tooling on the machine.

For pre-glued PVC, veneer, & melamine laminate coil stock; 0.4 - 1.2 mm edge thickness; up to 35 mm panel thickness cap., automatic coil feed. -- Equipped with: Electronically controlled temperature setting for hot air blower; 3,000 Watts for up to 650° F temperature; (1) Min heat up time. -- Guillotine type front & rear end trim (with fast speed, flying knife); top & bottom flush trims with single motor drive to cutterheads. -- Overhead belt type feeder; 16 FPM feed speed. -- Mounted on machine base with panel support table.

VITAP BLITZ CNC BORE, GLUE & DOWEL INSERTER: -- Specifications:(1) CNC Controlled head assembly with rapid (side-to-side) traverse, assembly with boring, gluing & insertion unit, This Flexible machine is IDEAL for JIT or high production runs. -- Working Area:Useable working area "X" axis 36.2" (920 mm), "Y" axis 3.14" (80 mm), "Z" axis up to 1.57" (40 mm) material thickness with digital readouts -- BG & D Unit(1) 1 HP - 6,000 RPM horizontal drill motor; 0.47" (12 mm) Maximum drill bit dia. (1) Glue injector & (1) dowel Inserter with 1.57" (40 mm) Max. dowel lengthMachine is capable of processing dowel diameters from 6 mm dia x 25 mm long - 10 mm dia x 40 mm long dowels (currently setup for 8 mm dia dowels); -- Operator & Machine Control:CNC "Color Touch-Screen" Controller for function & simple part programming and program storage. -- Complete with: (1) 12" Dia. vibratory feed hopper, totally sealed electronically metered glue system with "Automatic" injector flushing; (1) 4.75 G (18 L) Glue tank & (1) 2.37 G (9 L) water tank;(4) Inclined vertical pneumatic hold-down clamps; Function selector control for boring only or doweling; Anti-slip table surface, Rack & pinion drive and centralized dust collection manifold.

VITAP - BLITZ: CNC Bore, Glue & Dowel Inserter -- Specifications(1) CNC Controlled head assembly with: Rapid (side-to-side) traverse; assembly with boring, gluing & insertion unit This "flexible" machine is IDEAL for JIT or high production runs. -- Working AreaUsable working area: "X" Axis 36.2" (920 mm); "Y" axis 3.14" (80 mm); "Z" axis up to 1.57" (40 mm) material thickness with digital readouts. -- BGD Unit(1) 1 HP - 6,000 RPM Horizontal drill motor; 0.47" (12 mm) max. drill bit dia.; (1) glue injector & (1) dowel Inserter with: 1.57" (40 mm) Max. dowel length.Machine capable of processing dowel diameters from: 6 mm Dia. x 25 mm long - 10 mm dia. x 40 mm long dowels (currently setup for 8 mm dia. dowels). -- Operator InterfaceCNC "Color Touchscreen" Controller for: Function & simple part programming and program storage. -- Complete with: (1) 12" Dia. vibratory feed hopper; totally sealed electronically metered glue system with: "Automatic" injector flushing; (1) 4-3/4 G (18 L) Glue Tank & (1) 2.37 G (9 L) water tank.(4) Inclined vertical pneumatic holddown clamps; function selector control for boring only or doweling; anti-slip table surface; rack & pinion drive; centralized dust collection manifold.

VITAP ALFA 21 CONSTRUCTION/LINE BORER21-Spindle boring head on 32 mm centers. -- Specifications: drills vertically from bottom up and head rotates to horizontal position for edge boring, head rotation is pneumatic with switch control. -- 2-3/4" Max. drilling depth, 2.5 HP - 2,800 RPM motor, pneumatic drill head advance with speed control; head height adjustment with mechanical digital readout; 34" x 20" table size, max. workpiece width 31-1/2". -- Equipped with: Left & right side fences for construction boring, (2) pneumatic holddown clamps, line boring fence w/flip stops, pneumatic foot pedal control, magnetic starter & overload protection, and (1) set of quick-change chucks.

VALPATO LBK-150-ST 1 Feed Through Profile SanderTECHNICAL FEATURES: An added small needle type drum sander can be fitted with drum sanding aggregates of 25, ­30, ­35,­40, ­45 ­50 mm diameters which can be used for tighter curves and smaller radius sanding requirements. Storage compartments (2 in total) are located on each machine extremities, these are easily accessible and can be used for sanding belts and various tooling storage. Sanding belt motor power: 3 Kw Abrasive head motor power: 1.5 Kw Oscillation motor power: 0.38 Kw Feed motor power: 0.75 Kw Motor power for electrical adjustment of sanding group: 0.19 Kw Machine voltage: 480/3/60 Full Load Amps @ 480V: 15A Compressed air: Not required Dust collection requirement one (1) only 6" (150mm) port: 950 CFM Sanding belt speed: 14 Mt/sec Variable speed of the belt: from 5 to 25 m/min Sanding belt dimensions: 150 x 2640 mm Height of working table: 930 mm Dimensions of front working table: 1980 x 250 mm Machine dimensions: 2500 x 900 x 1600 mm Net weight: 1000 KMAIN FEATURES: User friendly PLC touch screen control panel is accessible from 360° by the operator, the control panel is centrally located on the infeed end of the machine. Factory installed variable feed drive (VFD), enables machine to run from 5 M/Min to 25M/min (+/­ 80 ft/Min). The entire sanding plenum rise and fall is motorized, it can be adjusted vertically in height to utilise the full height/width of the sanding belt. An oiling unit ensure long life of sanding plenum rise and fall master cylinder.

VOORWOOD M 15A CNC Round End Tenoner & Mortiser for 45° Door --The "M15A" Miter Machine is designed to rapidly make mortise and tenon cuts at 0°, 45° Only, . Parts can be up to 1.5"; thick and up to 4"; wide, and of ANY length. --A primary application for this machine is for miter cabinet door frames. Parts can be quickly transferred from left to right. They are mortised on the left side of the machine and tenoned on the right. The machine can also mill the slots. --Specifications & Equipped with: -- The mortise station has (3) servo-controlled axes (X, Y, and Z) that are coordinated by the machine controller to achieve complex CNC motion. It is equipped with a collet-style router spindle for cutting. The tenon station uses the same X- and Y-servo-controlled axes as the mortise station and is configured for pneumatically actuated in-and-out movement along the Z-axis. The tenon station is equipped with a direct drive shaper spindle for cutting. -- Pneumatic clamping assemblies with non-marring urethane pads are mounted to the hold-down assembly to secure the parts during cutting and these can be adjusted to various locations over the cutting surface. -- M15 Miter Machine operator interface consists of a colored touch screen. For simplicity, the entire calibration, setup, and monitoring of the machine are accomplished using only four touchscreen displays. The program designs the depth and location of both the mortise and the tenon. When the design is complete, it is saved in a recipe format. Once this recipe is opened, the operation is as simple and boils down to feeding the substrate into the machine. -- The full-color touchscreen panel is located on the front of the machine to provide easy access for setting up or operating the machine. Clamping and shaping operations are controlled by operating lighted pushbutton switches.