RONNING ENGINEERING Single Pass 10.5' X 40' Dryer/Cooling Drum;Complete with the following components: -- Like new condition, used approximately 1000 hours. -- Trunnion bases with Wheels & Drum Guide Idler. -- Gearbox/base (no motor). -- Insulation -- Endplates. -- This is a hi-performance design with full panel flighting originally set up as a cooling drum. The heat exchange surface is greatly increased with the addition of the panel flighting for which other standard single pass coolers/dryers would need to be much larger to compete with. -- Originally, this was set up has a cooling drum, but by simply reversing the air flow would make it an equally hi performance single pass dryer.

For dumping (1) load at a time. Hoist is fabricated from steel tubing with a box cradle that pivots at the top. The cradle holds the box as it is pivoted up to 135° to the final dumping position. The cradle is pivoted with a hydraulic cylinder driven by a 3 HP hydraulic pump. The cylinder is manually energized via operator foot-switches. -- System includes all mechanical equipment, electric powered hydraulic pump, and (2) foot switches. All wiring and controls by others. ~ Accepts a standard 96" long X 60" wide X 60" high box.

For dumping (1) load of fingerjoint blocks at a time. Hoist is fabricated from steel tubing with a box cradle that pivots at the top. -- 3-Sided cradle will hold the box or pallet when it is pivoted up to 135° to the final dumping position; cradle opening is 88" long X 48" wide X 50" high. -- A pair of replaceable forks hold pallets in place in the cradle. The cradle is pivoted by a hydraulic cylinder driven by a 3 HP hydraulic pump. The hydraulic cylinder is manually energized by the fingerjointer operator with foot switches. -- Scope of supply includes all mechanical equipment, electric powered hydraulic pump, and two foot switches. All wiring by others.

For dumping (1) load of fingerjoint blocks at a time. Hoist is fabricated from steel tubing with a box cradle that pivots at the top. -- 3-Sided cradle will hold the box, pallet, OR unit when it is pivoted up to 135° to the final dumping position; cradle opening is 88" long X 48" wide X 50" high . -- A pair of replaceable forks hold pallets in place in the cradle. The cradle is pivoted by a hydraulic cylinder driven by a 3 HP hydraulic pump. The hydraulic cylinder is manually energized by the fingerjointer operator with foot switches. -- Scope of supply includes all mechanical equipment, electric powered hydraulic pump, and two foot switches. All wiring by others.

ROSE GBUB-80 Glue-Bound Unit Breaker. Machine breaks the glue bond in a staggered stack of finger jointed material - see picture of material with the checkerboard end pattern. --Features -- Equalized Hydraulic squeeze, provides uniform load compression. --Hydraulic length change. Air operated Locking Pins on the Backstop Platen. --Backstop platen position indicator. --Simple manual controls for load length adjustment and crushing stroke on the control panel. --Heavy Duty Structural Steel Construction, Ease of Maintenance and Simple Operation (no cables).Does not use cables!Specifications: --Maximum opening is 16’-10"; for a single 4' x 4' x 16' unit. --Backstop Platen locks at 12" increments (2' minimum load length) --Pressure Platen, hydraulic actuated with 18" stroke. --Platen size 5' x 5' --5 HP Hydraulic Unit with a Pressure Compensated Pump (approx. 1 minute squeeze time) --Overall size approximately 5' x 25' x 7' high --480 VAC, 60 hertz, 3 phase, 30 ampsOptions: --10 HP hydraulic unit with approx. 30 second squeeze time, add $4,200 --Double unit capacity; crushes (2) 4' x 4' loads with 5' x 10' platen, add $19,700 --Automated Control Package with 2 Remote Controls for initiation of Pressing Stroke; Automatic open and hydraulic shut down; PLC Controls, automated load length adjustment with lighted indicators, add $ 7,400

ROSE BPUDH BOX, PALLET & UNIT DUMPING HOISTDescription: --Box, Pallet & Unit Dumping Hoist, for dumping one load at a time. --The hoist will be fabricated from steel tubing with a box cradle that pivots at the top. The three sided cradle will hold the box, pallet, or unit when it is pivoted up 135 degrees to the final dumping position. --A pair of replaceable forks hold pallets in place in the cradle. --The cradle will be pivoted by a hydraulic cylinder driven by a 3 HP hydraulic pump. The hydraulic cylinder is manually energized by the operator with foot switches. --Manufacture will supply all mechanical equipment, electric powered hydraulic pump, and two foot switches. --Cradle opening is: 168";L x 60";W x 60";H.Payment Terms: --50% with order, 40% prior to shipment, and the balance 10% net 30 days after receipt of equipment. Delivery is subject to the order file at the time the order is placed.Lead Time: --Delivery can be made in 12 weeks ARO at this time.Conditions: --The fabricated frames and appropriate parts of the items in this quotation will be painted with one coat of industrial grade Shady Lane Green enamel. Guards and appropriate moving parts will be painted Safety Orange. All gear-motors, mechanical equipment, limit switches, sensors or photoelectric devices as required for each item of this quotation, will be supplied and mounted. All pneumatic cylinders or other pneumatic power devices and their valves will be supplied and mounted. They will have connecting hoses and fittings installed. Filter/Regulator units will be supplied, mounted and connected by hose to the valves. Compressed air service to equipment is by others.Exclusions: --This proposal describes the machinery to be provided by Rose Machinery Inc. to the Buyer. The equipment supplied by Rose Machinery Inc. is specifically limited to the items actually described in the itemized detail pages of this quotation. Unless specifically mentioned herein, all other items and services are the responsibility of the Buyer. We do not include any state or local sales taxes, or any permit or other fees that may be required. All field wiring, plumbing, and installation is not included. Warranty: --Rose Machinery Inc. d.b.a. Complete Millwright Services, warrants all products of its manufacture to be free of defects in material, and workmanship, for a period of one year from date of shipment. Equipment provided by other manufacturers and incorporated within equipment manufactured by Rose Machinery will be warranted to the extent of the warranty provided by the respective manufacturer. Rose Machinery agrees to repair, or replace, at its option, any component found to be defective provided the purchaser promptly notifies Rose Machinery of the defect. Rose Machinery shall not be liable for incidental or consequential damages arising from said defective material. No other warranty written or implied is offered beyond that stated above unless specifically written and signed by an authorized a

ROSE MACHINERY BDH/LC/LCFT Automated Infeed SystemAutomated, high speed Infeed System for Gang Rip Saws of all makes and models and other similar machines. -- 5-Arm Breakdown Hoist - Electric hoist accepts loads 4' wide x 4' high x 4' - 24' long; 10 HP gear motor (with brake) powers the hoist and holds the load. -- Hoist actuated through foot switches for up & down; limit switches provide max. up & down positions; (5) lifting arms tilt load at 50° allowing layers to spill onto the takeaway conveyor; 16,000 Lbs. max. lift cap. -- Landing Chain - Features: (6) Strands of roller chain; powered by a 5 HP gear motor at 60 FPM nominal rate. -- Tail end constructed with integral slide, stock transits from Breakdown Hoist; head shaft & gear motor supported by tubular steel frame with bolts to allow for leveling at installation. -- Material stops at the head end so the operator can flip & grade each piece. -- Chain races fabricated from steel, UHMW PE wear strips on the top race and on the return race; conveyor is 42' long. -- Magnetic motor starter with foot switch for operator to start & stop of the chain. -- Lateral Chain Feed Table "LCF2013-20": Feeds material 3" - 10" wide x 4' to 24' long x 1" to 3" thick; variable 50 - 200 FPM Feed rate; adjustable fence throughout 3/4" range for alignment with the Rip Saw (or other machines). -- (6) 30" long, low friction steel flattop infeed chains for long life non-marking transport; 1 HP gear motor. -- (3) Powered smooth steel & non-marking feed rolls, 2 HP gear motor; rolls & chains controlled by variable speed drives. -- (3) Overhead pinch rollers, 5" dia., urethane covered; 1st (2) pinch rollers powered by individual 2-1/2" bore air cylinders to singulate pieces onto a 2' bridge; 3rd roller keeps the board moving on the bridge; pinch rolls triggered by photoelectric cells. -- Note: Fabricated frames and appropriate parts of the items in this quotation will be painted with (1) coat of industrial grade Shady Lane Green enamel; guards and appropriate moving parts painted with Safety Orange. -- All gear motors, mechanical equipment, limit switches, sensors or photoelectric devices, as required for each item of this quotation, are supplied and mounted; all pneumatic cylinders or other pneumatic power devices and their valves supplied and mounted; connecting hoses & fittings installed. -- Filter/Regulator units supplied, mounted, and connected by hose to the valves; Note: Compressed air service to equipment is by others.

Ripsaw Feeder with 32" wide feed rolls on 18" thru 28" roll centers; will feed 3' thru 16' lumber. With 24" of in-out fence travel; feed speeds from 50 to 150 FPM; 3/4 HP feed roll drive and 3/4 HP fence drive via gear motor with brake. -- Fabricated frame of structural steel with boots that allow +/- 1" elevation adjustment. 3-1/2" dia. steel feed rolls driven by a variable frequency drive for speed adjustment; rolls are canted to aid in holding stock against the fence. -- Powered fence with 24" fence travel is easily shifted via joystick control for stock alignment with the sawblades. -- With pneumatic powered gate to keep material from feeding until the operator initiates the feed sequence. -- Urethane covered idler pinch roll is attached to the fence and is powered down at the start of the feed sequence. When a photocell detects the board is clear of the gate, the pinch roll and gate will return to their normal position. Electrical control panel ready for connection to the power supply.

ROSE MACHINERY HBR Horizontal Band RE-RIP SawThe Horizontal Band Re-Rip Saw is an effective and efficient means of ripping short blocks into as many as six (6) set rip widths. Rip widths are easily adjustable, as well as the setting for stock thickness.Advantages of the system: -- Compact, efficient use of floor space. -- Accurate cutting of rips with minimum tear-out. -- Short blocks, 4" minimum length, without taper problems. -- Straight through feed design, good for sorting. -- Minimum dust collection required. -- Single point scrap collection. -- One saw drive motor, requires less power. -- Safety, no kickback problems.Specifications: -- Five (5) rip widths - (6) optional -- 20 HP bandsaw drive -- 30" diameter band wheels, 2" wide face -- (2) 3/4 HP feed works drives -- 1-1/2 HP feed belt drive -- 1" to 6" rip width (independently adjustable in each lane) -- 10" maximum board width at maximum rip -- 4" maximum waste piece width -- 3/4" to 2" stock thickness (all lanes adjust together) -- 4" minimum stock length -- 36" maximum stock length -- 80 FPM feed speed -- 52" to 58" pass line height -- Motor starters and push buttons included, wired for 440 volt, 3 phase, 60 Hz (uses standard mag starters) -- An automatic band lubrication system is includedOptional Equipment: -- For SIX (6) LANES, add ...$5,600 (SORTER increases $3,700) -- Automatic machine grease lubrication system, add ...$ 9,200 -- Ergonomic overhead stock slide, add ...$ 5,600 -- Output conveyor and sorter for 5-LANEsingle side discharge, add ...$47,300 -- Output conveyor and sorter for 6-LANE single side discharge, add ...$51,100 -- Operator's platform, add ...$ 7,900 -- Optional voltage configuration: 220/380/440V, 50HZ, add ...$2,900 -- Start-up and training, add $1,000 per day plus expenses at costHorsepower Requirements: -- (1) @ 20 HP -- (1) @ 1-1/2 HP -- (2) @ 3/4 HPDust Collection: -- (2) outlets, 6" diameter, 5,200 FPM velocity @ 2,300 CFMCompressed Air Required: -- 90 PSI @ 1.4 CFM

2022 CNC controller! Under power & ready to demo! 3-Axis CNC Vertical Milling Machine - Seller has outgrown and upgraded to larger capacity CNC Machining Center. - Table size 10" x 50" x 38” H - Travels: X-Axis: 31", Y-Axis: 17", Z-Axis: 23-1/2" - Quill travel 5" - Quill diameter 100 mm (3.94") - No. 40 Spindle taper - Variable spindle speeds 80 - 4,000 RPM - Rapid traverse 150 IPM - Distance from spindle nose to table (Maximum part height) 23-1/2" - Distance from spindle center to column face 19" - Maximum weight of workpiece 1,320 Lbs. - Maximum work capacities: 1" Drilling & Tapping mild steel & Milling (Metal removal rate/mild steel) 5 cu. in./min. - 5 HP Spindle motor - 560 in-oz Continuous torque D.C. servo motors & Precision ground ball screws for X, Y, & Z-Axes - YEONG DIEN Automatic lubrication unit Includes: - 2022 "PROTOTRAK SMX3" 3-Axis CNC Control/3-Axis Digital Readout (Control defines tool path based upon user defined part geometry), with Pentium PC-processor with 512 MB RAM, 10.4? Color active-matrix screen, Touchpad, (4) USB connectors, MICROSOFT "WINDOWS" Operating system, Program feedrate override & Tool path graphics - ALL MACHINE PARTS "MAXI TORQUE-RITE" Pneumatic drawbar, with 40 - 50 ft. Lbs. of torque - EKSTROM CARLSON "MISTIC MIST 1ST-2LC" 1 Gallon Capacity Coolant Mist Generator, with Adjustable air & Liquid control valve - WALDMANN "ROCIA.FOCUS" 600 Lumen 5,000 K Sealed Housing LED Work Light

SPEC AIR Model R120-26RD-OC Baghouse Filter Auto Shaker Type Dust Collector Loaded with features. -- Capacity of approx.15,500 CFM and the following features and components: -- EB-26, 60 HP SPEC AIR, Air Handling Fan , 15.500 CFM @ 16" SP mounted in a negative pressure configuration (clean air side) with return air and with automatic 26" dia. Abort Gate Damper according to NFPA-68-69 CODE. 110 volt actuated by the Spark Detection System. -- HANSENTEK AN104 Spark Detection/Suppressions system Per NFPA 64-68 and c/w BPS-9X4 Booster Pump & FLEXCON P2P20 Tank. -- 1,961 sq. ft. of filter area using (97) high efficiency Polyester bags. Operating at 7.9 to 1 ACR (Air to cloth ratio). -- 26"; Diameter Inlet & outlet duct. -- Tangential inlet with Backflow Damper, according to NFPA-68 CODE. -- Top mounted motorized bag shaker. mechanism powered by 1.5 HP. -- Rotary Air Lock with 96" clearance. (4) leg support steel frame & Safety access ladder. -- Explosion Venting Doors, according to NFPA-68 CODE. -- Filter Bag size approx. 9" dia. x 9' long, -- Inline 26" dia. Silencer muffler on return air duct. -- Ground mounted Belt Driven Fan complete with TEFC motor and inspection door. -- Features: 60 HP Soft Start Controller. -- ENGINEERED ELECTRIC Control Panel with starters and controls. -- Manometer gauge to monitor differential pressure (life) of filter media. -- Housing/Support Steel dimensions: 120" long x 120" wide x 32' high. Approx. 13, 500 Lbs. -- Some pictured pipe is included.

SPEC AIR Model R-44SQ Dust Collector with Shaker Bag Cleaning, Abort Gate, Spark Detection, Rotary Air Locks and Relay Fan in a closed loop configuration. -- Overall Data: 46,000 CFM with approx. 6170 sq. ft. of cloth area consisting of (286) filter bags operating at 7.4:1 Air-to-Cloth Ratio (ACR). 'Can velocity' (upward) is 211 FPM. Polyester filter bags are 9" dia. x 110" long. -- Fan:/Motor: SPEC-AIR EB-44 Clean Air Fan with approx 44" dia. inlet/outlet, ground- mounted in an upblast arrangement. Fan can deliver 46,000 CFM @ 16" SP. Inspection door, and belt guard. Belt-driven by a TOSHIBA 200 HP High Efficiency (Inverter Duty), TEFC motor, 447T frame at 1780 RPM. -- Bag Cleaning: Via (2) Shaker motors with a lattice of tie-rods inter-connected to each row of bags. Bags are accessed from the top clean air plenum.Timer relay from low voltage controls for bag cleaning. -- Comes with: (2) Tapered hoppers separating the large particles, large access door, Backdraft Dampers adapted to (2) 32" filter inlets, lower hopper bottom each with Rotary Air Lock. Discharge from both RAL's is connected to a Material Handling Transfer/Relay fan into an enclosed container (not included) for continuous collection of waste. A return pipe from container makes this a closed loop configuration. Explosion doors. Safety ladder to top return air plenum.. Magnehelic differential pressure gage to monitor the condition of the filter bags. -- Construction: Heavy gage construction with reinforcing ribs and Flange-bolted in the middle easily allows units to transport into two units, ie 120" x 141".Return Air starts from filter outlet with adaptor to 44" dia. fan inlet. Discharge Silencer of fan outlet has a 44" Abort Gate returns air into building. -- Features: HANSENTEK Spark Detection system. Main electrical panel with pushbottons and controls. -- Includes: Filter housing and outside pipe is fully covered with insulation to minimize heat loss & reduce plant heating cost. -- Overall dimensions: 282"; Long x 120"; Wide x 317"; High. Weight approx. 20,000. Lbs. -- Note: Unit was moved in 2020 to current location and refurbished for new installation.

SPEEDAIRE - 4B228D, ...Portable CompressorSpecifications: -- 6 HP Reciprocating Air Compressor; Pump # 4B247A; 10.3 SCFM @ 90 PSI; 9.1 SCFM @ 135 PSI. -- Max. pressure rating: 135 PSI; 26-Gallon horizontal air receiver on (2) wheels; motor and flywheel guard.6 HP Motor, wired for single-phase, 240 Volts, 15 Amp. -- Complete with: -- Single-stage Compressor head; air pressure regulator gauge, and tank pressure gauge; start-stop auto or manual cycle controls; pressure relief valve. -- (1) Air discharge port with quick disconnect.

SPROUT Rotary Drum Dryer with Gas Burner;Complete with the following components: -- 7.5 Ft. x 24 Ft. Steel Rotary Dryer Drum. -- Natural Gas Burner (may be converted to LP) with 13.5 Ft. Refractory Lined Furnace Tube. -- Belt Drive with Gear Reducer and Electric Motor. -- Trunnion Bases complete with Forged Trunnion Wheels. -- Forged Trunnion Tracks (weld-on style) ...look like new. -- Vertical drop material Inlet Transition with Side Access Door. -- Rated for approx. 2 TPH water evaporation or about 4.5 TPH wood sawdust input. -- OPTIONAL ITEMS: &#9679 Receiving Bin with Airlock and Screw discharge Conveyor. &#9679 Material Input Screw Conveyor. &#9679 Main Fan.

SQUARE D - 75T3H, ...75 KVA, 480 - 208 V, 3-Phase Autotransformer Specifications: -- Intended for power, heating, and lighting applications. -- Enclosure Rating: NEMA 2. -- Multi-Tap (432 - 504 V) Primary 480 V (Delta); Secondary 208Y / 120 V @ 60 Hz ventilated. -- Aluminum windings. -- cULus Listed. (2) Available; price per unit. - Make offer for both!

SSI - M-70-E, ...Dual Shaft, Low-Speed, High Torque ShredderEffective in bulky item reductio; product destruction or preconditioning (primary shredding) where output particle size variation is acceptable. Output consists of strips the width of the cutters (usually 1" - 3").Equipped with: -- 60 HP Drive motor; cutting chamber 29" x 40"; hopper opening 55" x 67"; cutting disc diameter 14.4"; cutting disc thickness 1-1/2". -- Auto reversal protects components; advanced bearing protection system assures longevity. -- Suitable for: Wood, plastics, electronic scrap, medical waste, textiles, and tires.

SSI Model - 1000-E, Slow Speed, High Torque ShredderSpecifications: -- 50 HP Motor; twin shafts; 40" x 25" ChamberIncludes: -- Stand, feed hopper; controls

2019 STANZA - PM-251, ...Lateral Outfeed Transfer : Demo unitWorking Machine Parameters:Workpiece length: 3’ Min. - 9’ max.Workpiece width: 1/2" Min - 8" max.Speeds: 30 - 150 FPM.Number of dropdown rolls: 10.Number of crossbelts : 4Crossbelt spacing: 20" on Center.This is a Demo unit in "Like New" condition. - Great for parts up to 9 ft. long feeding into your next operation.

STAR V MACHINERY SCG-1600 AUTOMATIC CROSS GROOVER + TIGERSTOP TS08 STOP/PUSHER: -- Specifications:(1) Spindle with 7.5 HP - 3,600 RPM motor, 60" max. crosscut cap., material thickness 0.25" - 1.125"; head up & down movement via pneumatic cylinder with linear rail & linear bearings, depth fine adjustment with special threaded adjustable unit. -- Carriage cross-travel powered by a 3 HP hydraulic motor (4GPM), driven ball screw with linear rail & linear bearings; feed rate from 0 - 40 FPM; Heavy Duty welded frame construction. -- Complete with:Safety guards and cutter guards; pneumatic support fence; heavy-duty in-feed & out-feed roller tables. -- Options Include:&#9679 TigerStop TS08, 8' (96") long, NC controlled stop/pusher system, mounted to the LH side of the machine. &#9679 (4) manual flip-stops with Pro-Scale digital readouts, for 60″ of scaled capacity, mounted to the RH side of the machine. &#9679 Reciprocating taping machine is built directly in front of the bed of the cutting area eliminating the need for taping by hand -- Actual Model is STAR V MACHINERY SCG-1600 AUTOMATIC CROSS GROOVER + TIGERSTOP TS08 STOP/PUSHER.

STAR V MACHINERY SLG-2000 36 LINEAR V-GROOVER: -- Specifications:Working table dimensions are 120" long x 36" wide; Working width from 4" - 36"; Working length from 20" - infinite; Working thickness from 0.25" - 1.2".Maximum throat clearance for linear & cross-cuts is 15". -- Equipped with: (2) Independent, 12 HP-3,600 RPM Saw Motors with "servo" control adjustment in "Y" axis & manual "Z" axis adjustment.30 mm Dia. Arbor x 4" clamping length to accommodate wider cove back splash, triple-fold profiles, or using it for hogging and finish cut; 9.5" max. cutter-head dia.1-Saw motor is mounted on the front & 1-Saw motor is mounted on the back of the 8" x 12" x 1/2" heat-treated steel heavy-duty overhead support beam.Side to side head travel via linear rails & bearings, manual head height adjustment via linear rails & bearings. -- Feeding System:(1) 3 HP Variable speed drive belt system with "servo" height adjustment; Feed rate from 0 - 60 FPM, belt feeder moves workpiece on a precision "stainless-steel" roller table; -- Tape Applicator: (2) Automatic Tape Applicators with "servo" adjustment, according to the Saw motor position in "Y" axis. -- Operator Interface:10" HDMl Touch Screen Display for Start/Stop, On/Off, Feed Speed & Axis Position. -- Complete with:; Safety guards and Cutter guards. Anti-Kick-back Device. Emergency Shutoff line. Dust collection requirements 4,200 CFM, collector outlets on cutter guards 5" in dia.. -- Options Include:&#9679 Increased Working Width Capacity from standard 36" to 40" (1,016 mm) &#9679 Modify Feeder System to allow 2" Thick Material to pass. &#9679 Increased Cutter Guarding & Motor Shafts to accept tooling & process 2" Thick Material &#9679 (1) 10'x30" (3mx76cm) lnfeed Conveyor &#9679 (1) 10'x30" (3mx76cm) Omni Directional Ball Transfer Table &#9679 (2) Brazed Carbide 90 Degree V Groove Cutter for up to 1" Thick Material &#9679 (2) Rolls of 2" (50mm) wide V-Groove Tape. -- Actual model# is STAR V MACHINERY SLG-2000 40-2".