TWIN FLOW Air Make-Up Unit 7,000 CFM. Vertical mount with Remote Control Panel: -- CFM: 7,000 CFM @ 1.75" ESP, 5HP/575v/3ph/60Hz TEFC motor -- BTU: 0.68 MBTUH -- Burner: MAXON burner -- Temperature Control: 80º F temperature rise in spray cycle -- Mounting: Vertical, outdoor/indoor mounted -- Fuel required: Natural gas, 0.3 PSI pressure -- Intake/Discharge: Vertical, screened, air intake with vertical discharge -- Filter Sections: V-Bank style with 1’’ cleanable air intake disposable type filters -- Gas Control: Control cabinet and pre-piped gas combustion system mounted on burner section to FM, Electronic Modulation -- Specifications includes: Digital Temperature Controller, ON/OFF & Summer/Winter Switch, pressure regulator, metering valve, pilot pressure regulator & pilot gas valve, flame rod, high limit switch, air flow switch, power transformer, ignition transformer and spark plug -- Electrical Control cabinet includes: main breaker disconnects, magnetic motor starters with adjustable overload protection for air makeup, motor fuse protection -- Motor Control: Control cabinet includes: main breaker disconnects, magnetic motor starters with adjustable overload protection for air makeup, motor fuse protection -- Enclosure Design: Framed, with 18 ga. metal walls and 1" insulation -- Note: Available in Horizontal and Vertical mount. Please inquire.

TYLER 703 Power Pod Cold PressTyler Air Pod Press with a Platen dimension of 40″ Wide X 87-1/2" Long. -- The Maximum Daylight Opening is 49.5″, and the pods will extend 9.5″ for a minimum opening of 40″. -- The top and bottom plates are dent free. -- The press is rated to 100 PSI and has (1) pod short of 100% pod coverage (being that the center bags are staggered). -- There are spring loaded bed rollers to aid in loading and unloading. .This machine has been cleaned and checked and there are no air leaks.

--In Auctions; https://exfactoryauctions.com/Detail/DL-230113/event/A122024$1 - NO RESERVE -- TYLER French-Type Dovetail Machine Equipped with: (2) 14-1/2” x 17” Tables. (2) 2 HP Routing heads for mounting of drawer sides. (1) 2 HP Grooving head for drawer bottom dado, (2) 2-Spindle Vertical boring heads for drawer hardware. (2) Pneumatic hold-down clamps

TYLER - 2400: Slat-Wall Machine -- SpecificationsProduces T-slots "Slat-Wall" for architectural/store fixture panels.48" x 97" Max. panel capacity., 24" x 24" min. cap., panel thickness 1/2" to 1-1/2". Machine capable of processing up to (40) panels/Hr; depending on material density, thickness, and the slot profile. -- Equipped with:Machine is currently setup with: (18) Router spindles on 3" centers.Spindles are driven in groups of (3) with: (6) 7-1/2 HP - 3,450 RPM Motors that drive the (18) router spindles; all router spindles rotate @ 15,400 RPM.Machine can accept up to (21) router spindles & the additional spindles can be activated by adding (1) additional 7-1/2 HP - 3,450 RPM motor. -- Machine Operating SequencePanels remain stationary on top, pneumatically clamped in place while the bottom mounted router bank traverses the full length of the panel with a high-speed return,Variable feed speed control, router assembly traverses on ground & polished rails with chain drive.Panels are positioned along the 8' rear edge fence line; distance from the panel edge to the centerline of the 1st cut can be adjusted from 0.0" - 3" (1 router spindle pitch). -- Operator & Machine ControlALLEN-BRADLEY Electrical controls for the machine cycle; "setup" mode of operation.Machine cutting cycle is initiated by: 2-Hand Operator safety buttons located on the right front of machine. -- Complete with:Overhead holddown assembly with: (2) Large air cylinders; (6) arms with spring loaded clamping pads hold the panel in place.Panels are loaded from the 8' front and exit to the side for easy unloading. -- Options Include: Assortment of used "Diamond Tooling" (diamond router bits) Assortment of extra motors Spare parts Service manual & docs. -- Actual Model: TYLER 2400

UAS -BHT (CALCOR) MIB-11-T19- SVA Pulse Jet baghouse dust collector. MIB is Modular Industrial Baghouse. -- Has qty (18) each of filter cartridge # 04007500 (6.125 x 75") and qty (18) each of filter cartridge # 0400000249 (6.125 x 41.6250"), for a total 1,896 sq. ft with pleated Spunbonded Polyester w/PPTFE filter bags. -- OEM rated for 5,000 ACFM @ 11" SP, resulting in a 2.64 Air-to-cloth ratio. -- 20 HP Siemens motor, on a large floor-mounted blower -- Comes with DPC and Timer board for Pulse Cleaning Control. Allen Brady Starter and air quality motoring. -- Discharges thru Pyramid hopper into a 55 Gallon Drum. Includes dome style explosion vent.. -- Housing dimensions: 60" x 60" x 232" high. Total weight with filters: 3800 Lbs. -- Looks like its brand new. -- Last used for a CNC Laser Cutter.

UHLING HP 4000 Case ClampOne of the most versatile, quick, and easy-to-use Case Clamps on the market!Specifications: -- 100" x 50" x 24" Clamping cap. that's UHLING's most versatile Clamp ever. -- (3) Counterweight balanced, fully adjustable horizontal dual air pod pressure bars and (2) vertical, easy adjustable dual air pod pressure bars. -- 3-1/2" Stroke with individual controls for each air pod pair. -- Roller bearing mounted carriage with pneumatic locks (considered to be the fastest 2-axis Clamp on the market). -- Single lever lock-or-unlock control and front/rear pressure selection. -- Solid panel counter support that is opposite the pressure bars. -- Easy access operator's control panel that's mounted on the vertical beam. -- Approximately (30) Sec or less changeover time. -- Options: Additional dual pod pressure bar assembly for vertical or horizontal.

UHLING HP-3000 CASE CLAMP (SINGLE-BAY): --Specifications:Clamping Capacity: 55" L x 96" H x 24" D; large enough for multiple boxes. Offers versatility, quick 30-second setup or changeover. -- Pressure Elements:(4) Dual air pod pressure bars that are pneumatically activated; counterweight balanced; position them effortlessly and let go. The counterweight keeps them in place; no need to secure them! -- Air Pod Stroke:3-1/2" Stroke of air pod with 0 - 120 PSI pressure adjustment. -- Vertical Beam:Moves easily on roller bearings with pneumatic carriage locks; (4) small air cylinders from (1) control point. -- Operator Control Panel:Mounted on vertical beam, so it is always where it is needed; single-lever lock-or-unlock control & front/rear pressure selection. -- Counter Support by:Solid laminated panel opposite to pressure bars.

UHLING HP2000 Case Clamp (Pneumatic)Offers a compact, quick and easy-to-use Case Clamp.Specifications: -- 50" x 42" x 24" Clamping cap. that can handle 80% - 90% of your case good needs. -- (2) Counterweight balanced, fully adjustable horizontal dual air pod pressure bars. -- 3-1/2" Stroke with individual controls for each air pod pair. -- Roller bearing mounted carriage with pneumatic locks. -- Single lever lock or unlock control and front/rear pressure selection. -- Solid panel counter support opposite to pressure bars. -- Easy Access operator's control panel that is mounted on the vertical beam.

UHLING HP-4000 ... is a versatile, quick and easy-to-use Case Clamp.Specifications: -- 100" x 50" x 24" Clamping cap. that's UHLING's most versatile Clamp ever. -- (3) Counterweight balanced, fully adjustable horizontal dual air pod pressure bars and (2) vertical, easy adjustable dual air pod pressure bars. -- 3-1/2" Stroke with individual controls for each air pod pair. -- Roller bearing mounted carriage with pneumatic locks (considered to be the fastest 2-axis Clamp on the market). -- Single lever lock-or-unlock control and front/rear pressure selection. -- Solid panel counter support that is opposite the pressure bars. -- Easy access operator's control panel that's mounted on the vertical beam. -- Approximately (30) Sec or less changeover time. -- Options: Additional dual pod pressure bar assembly for vertical or horizontal.

UHLING HP-3000 Case Clamp ... offers versatility, quick (30) second set-up or changeover. -- Clamping Capacity, 55"- L x 96"- H x 24"- D, that's large enough for multiple boxes. -- Pressure Elements, (4) horizontal @ with (3) individual air pods, counter-weight balanced, position them effortlessly and let go, the counter-weight will keep them in place, no need to secure them! -- Air Pod Stroke, 3-1/2" with individual controls for each air pod set. -- Vertical Beam, moves easily on roller bearings with pneumatic carriage locks. -- Operator Control Panel, mounted on vertical beam, so it is always where it is needed, single lever lock-or-unlock control & front/rear pressure selection. -- Counter Support, by solid laminated panel opposite to pressure bars. OPTIONAL: Top Clamping, removable top pressure element for applications such as a vertical center partition or similar needs, removes easily if not needed. Add $ 1,000.00 to standard machine price.CUSTOM:HP-3000 F, ... comes with a "Solid Floor" for easy clamping of upper cabinets, add $ 1,000.00 to standard machine price.HP-3000 M, ... clamping capacity, 60"- L x 96"- H x 36"- D, that's large enough for deep commercial Case Goods. Please call for pricing.

UHLING - HP-3000: Case Clamp (Single-Bay) -- SpecificationsClamping capacity: 72" L x 74" H x 24" D; Large enough for multiple boxes; offers versatility, quick 30-Sec setup or changeover. -- Pressure Elements(4) Dual air pod pressure bars that are pneumatically activated; counterweight balanced; just position them effortlessly and let go: Counterweight will keep them in place; no need to secure them! -- Air Pod Stroke3-1/2" Stroke of air pod with 0 - 120 PSI pressure adjustment. -- Vertical BeamMoves easily on roller bearings; pneumatic carriage locks with: (4) Small air cylinders from (1) control point. -- Operator Control Panel:Mounted on vertical beam so it is always where it is needed; single lever lock-or-unlock control & front/rear pressure selection. -- Counter SupportBy solid laminated panel opposite to pressure bars. -- Actual Model is: UHLING HP-3000

UHLING - HP 2000: Case Clamp (Pneumatic) Specifications: -- Offers a compact, quick, and easy-to-use Case Clamp. -- 50" x 42" x 24" Clamping cap. that handles ...80% - 90% of your case good needs. -- (2) Counterweight-balanced, fully adjustable horizontal dual air pod pressure bars. -- 3-1/2" Stroke with: Individual controls for each air pod pair. -- Roller bearing mounted carriage with: Pneumatic locks. -- Single-lever lock or unlock control; front/rear pressure selection. -- Solid panel counter support opposite to pressure bars. -- Easy Access Operator's Control Panel that is mounted on the vertical beam.

UHLING - HP 4000, ...Case Clamp (Semi-Automatic) -- Specifications100" Wide x 50" high x 24" deep clamping cap. and built with a Heavy wall steel frame construction. - Super "easy & quick" manual positioning of vertical side pressure carriage and top pressure beam. -- Includes: Push button release, pneumatic locking and "counterbalanced" movement of horizontal top pressure beam; vertical side pressure carriage with single lever release & lock; locks in place with (4) air cylinders and rides on bearings for quick & easy positioning. -- Vertical & horizontal pressure beam equipped with: (5) Adjustable "dual" ram air pod pressure shoes (3 on the top horizontal beam & 2 on the side vertical beam); 3-1/2" clamping stroke; features individual air pod selection. -- Since the pressure bar is positioned over the joint (or shelf), it will automatically compensate for sizing inaccuracy. -- Independent controls for top & side pressure and timer for clamping cycle; solid bottom & back support for any size case. -- Air flow pressure controls & pressure gauges built into traveling vertical carriage (always close to the Operator). -- Overall dimensions: 143" x 90" x 30".

ULTRA GL-630H Feed Through Moulder: 6-Head (B-T-R/L-T-B), "Flooring" working capacity of 12" x 6".Specifications: -- Head sequence: Bottom 25 HP, top 30 HP, right 20 HP/left 20 HP (opposing), top 25 HP, and bottom 25 HP motor. -- Spindle dia. of 1-13/16" with cutterhead speed of 6,000 RPM; all spindles with high prevision bearings. -- Auto. positioning of the left & top spindles radially; all additional spindles with digital readouts, including chipbreaker & pressure elements. -- Pneumatics on all chipbreakers, pressure elements, and holddown rollers. -- Horizontal spindles with HydroLock outboard bearings on #1, #2, #5 & #6. -- Straight jointer on spindles #5 & #6; Profile Jointers on spindles #3, #4, #5 & #6. Equipped with: -- Inverter controlled feed drive, variable speed of 26 - 260 FPM. -- Infeed table 1.2 M (4') with all table plates & fences hard chromed to RC 70. -- Machine table includes: (5) Table rollers for smooth through feed; short stick attachment for through feed on pieces down to 230 mm. -- Electrical cabinet & pedestal for machine controls separate from machine, Heavy Duty sound enclosure. -- Includes Startup training and Warranty!

UMP - BP 450 A: 450 kG/Hr Briquette PressSpecifications: -- Cap. 450 kG/Hr (992 Lbs). -- Max. pressure: 1,700 kG/cbm (24,175 PSI). -- Max. chip moisture content: 15%. -- Max. chip size: 15 mm (0.59"). -- Wood shaving to briquette ratio: 10 to 1 (using mahogany). -- Briquette configuration: Rectangular. -- Briquette length: 40 - 105 mm (1.57" - 4.13"); Briquette width 150 mm (5.91"); Briquette height: 60 mm (2.36"). -- Briquette heat energy: 4,200 kCal/kG (7,558 BTU/Lbs). -- Hopper size: 31"; x 36"; x 36"; with: 1-Side sloping so cutaway from cube of 18"; x 36";; mounting flange at top allows additional capacity to be added.Equipped with: -- Automatic material density adjustment. -- Automatic hopper shutoff. -- SIEMENS PLC Control.

UNIMAK 160-S 5-Foot Wide Single-Sided Hot Melt Glue Spreader for Hot Melt Glue including PURHot Melt Glue Spreader for PUR and other Hot Melt Adhesives. Panel Types: MDF, particleboard, door spar, XPS, and polystyrene sandwich panels. All kinds of panels that adhesive application is required.Glue Types: Polyurethane hot melt (PUR) glue. Unfilled EVA,Pressure Sensitive Foil Types: As roll: PVC, P.P., finish foils and CPL foils As sheet Stock: Veneer, PVC, laminate, acrylic plates and door surfacesWorking Speed: 5 - 25 meter/Min (16.4 - 82 FPM)Technical Specifications: -- Max. External Working Temperature: 180 ° C (365° F) - chromed roller. -- Working Width: 200 - 1,600 mm (7-7/8" - 63"). -- Board Thickness: 4 - 40 mm (1/8" - 1-5/8"). -- Upper Spreader Roller, Silicone Coated and Ø 240 MM (9-1/2"). -- Upper Dosing Roller: Ø 215 MM – Chromed (8-1/2"). -- Lower Transport Roller: Ø 240 MM – Silicone coated. -- Total Power: 15 kWMelter and Hose are not Included, they are optional and can be quoted separately.

UNIMAK GS140-S Single Sided Hot Melt Glue Laminator4-Foot Wide Hot Melt Glue Spreader for PUR and other Hot Melt Adhesives. Panel Types: MDF, Particleboard, door spar, XPS and Polystyrene sandwich panels. All kinds of panels where adhesive application is required.Glue Types: Polyurethane Hotmelt (PUR) glue. Unfilled EVA.Pressure Sensitive Foil Types: As roll material - PVC, P.P., finish foils and CPL foils. As sheet Stock - Veneer, PVC, laminate, acrylic sheets and door surfaces. Working Speed : 5 - 25 m/Min (16.4 - 82 FPM).Technical Specifications: -- Max. External Working Temperature: 180 ° C (365° F), Chromed Roller. -- Working Width: 200 - 1,400 mm (7-7/8" - 55"). -- Board Thickness: 4 - 210 mm (1/8" - 2-1/4"). -- Upper Spreader Roller - 240 mm (9-1/2") diameter, Silicone Coated. -- Upper Dosing Roller: 215 mm (8-1/2") dia., Chromed. -- Lower Transport Roller: 240 mm (9-1/2") diam., Silicone coated. -- Total Power: 15 kWMelter and Hose are not Included, they are optional and can be quoted separately or purchased locally.

UNIQUE 313 Automatic Cope and Dowel Door MachineMiters the end and drills for dowels of (2) cabinet door rails on each pass, automatic cycle for accurate & easy alignment of mitered corners.Equipped with: -- (2) 5 HP Dual-motor set for shaping w/1-1/4" spindles; (2) 1/3 HP dowel alignment drills. -- Automatic cycle with dowel hole boring for accurate alignment of mitered door corners in (15) Seconds per cycle, -- 1" Material thickness capacity, 4" max. material width, 5" max. cutter diameter. Features: -- (2) Pneumatic clamps holds material during operation for safe machining of parts, Adjustable stops for dowel drilling, Air over oil rod-less cylinder driven table. -- Staggered tables with angled fences allow (2) 1" thick parts to be machined simultaneously; digital position indicator. -- Dust Collection: (2) 5" Dust ports require approx. 1,000 CFM per spindle.Includes - Standard Finger joint shaper heads to cut miters and drill bits for doweling.

UNIQUE 2753 Arch Shaper with Sanding HeadThe Unique Model 2753 Is A Single End Machine Designed For High Quality, High Production, Cabinet And Passage Door Arching Of Top Rails And Panels. Its Two Counter-Rotating Spindle Motors are Easily Programmed For Multiple Cuts With Hogging And Finishing Cutters To Eliminate Tear-Our And Extend Tool Life. A Sanding Station Provides A Multi-Pass Sanding Finish On Arched Door Panel Profiles. Unique “ArchPro"; Software Guarantees High-Speed Measuring And Fully Dynamic Programming Abilities.• Shaper Motor: (2) 10 HP Himmel Direct Drive , 440V - 39.2A, 3PH Motor• 5" Stack Height • Compressed Air Requirements: 90 PSI - 2 CFM• Dust Collection: (2) 5" Diameter 1200 CFM each (1) 4" Diameter 800 CFM each• Work Height: 3’6"• Machine Footprint: 113" Width X 78" DepthIncludes - Safety Mats, Dust Collection Manifold, and Owner's Manual

UNIQUE - 313, ...Automatic Cope & Dowel Door MachineMiters the end & drills for dowels of (2) cabinet door rails on each pass; automatic cycle for accurate & easy alignment of mitered corners.Equipped with: -- (2) 5 HP Dual motor set for shaping w/1-1/4" spindles; (2) 0.33 HP dowel alignment drills. -- Automatic cycle with: Dowel hole boring for accurate alignment of mitered door corners in (15) Sec/cycle. -- 1" Material thickness cap., 4" max. material width, 5" max. cutter diameter. Features: -- (2) Pneumatic clamps hold material during operation for safe machining of parts; adjustable stops for dowel drilling; air over oil rodless cylinder driven table. -- Staggered tables with angled fences allow: (2) 1" Thick parts to be machined simultaneously; digital position indicator. -- Dust Collection: (2) 5" Dust ports require approx. 1,000 CFM per spindle.